收藏本站
参数资料
型号： TMS320C6416TBZLZD1
厂商： Texas Instruments
文件页数： 87/146页
文件大小： 0K
描述： IC FIXED-POINT DSP 532-FCBGA
标准包装： 60
系列： TMS320C6414T/15T/16T
类型： 定点
接口： 主机接口，McBSP，PCI，UTOPIA
时钟速率： 1.0GHz
非易失内存： 外部
芯片上RAM： 1.03MB
电压 - 输入/输出： 3.30V
电压 - 核心： 1.20V
工作温度： -40°C ~ 90°C
安装类型： 表面贴装
封装/外壳： 532-BFBGA，FCBGA
供应商设备封装： 532-FCBGA（23x23）
包装： 托盘
配用： 701891-ND - KIT STARTER DSP FOR C6416T
TMDXEVM6452-ND - TMDXEVM6452
296-23038-ND - DSP STARTER KIT FOR TMS320C6416
TMS320C6414T, TMS320C6415T, TMS320C6416T
FIXEDPOINT DIGITAL SIGNAL PROCESSORS
SPRS226M NOVEMBER 2003 REVISED APRIL 2009
45
POST OFFICE BOX 1443
HOUSTON, TEXAS 772511443
Terminal Functions (Continued)
SIGNAL
TYPE
IPD/
DESCRIPTION
NAME
NO.
TYPE
IPD/
IPU
DESCRIPTION
HOST-PORT INTERFACE (HPI) [C64x] or PERIPHERAL COMPONENT INTERCONNECT (PCI) [C6415T or C6416T devices only]
(CONTINUED)
PCBE0
W3
I/O/Z
PCI command/byte enable 0 (I/O/Z). When PCI is disabled (PCI_EN = 0), this pin is tied-off.
For the C6414T device this pin is “Reserved (leave unconnected, do not connect to power or
ground).”
XSP_CS
AD1
O
IPD
PCI serial interface chip select (O). When PCI is disabled (PCI_EN = 0), this pin is tied-off.
For the C6414T device this pin is “Reserved (leave unconnected, do not connect to power or
ground).”
CLKX2/
XSP_CLK§
AC2
I/O/Z
IPD
McBSP2 transmit clock (I/O/Z) [default] or PCI serial interface clock (O).
DR2/XSP_DI§
AB3
I
IPU
McBSP2 receive data (I) [default] or PCI serial interface data in (I). In PCI mode, this pin is
connected to the output data pin of the serial PROM.
DX2/XSP_DO§
AA2
O/Z
IPU
McBSP2 transmit data (O/Z) [default] or PCI serial interface data out (O). In PCI mode, this pin
is connected to the input data pin of the serial PROM.
GP15/PRST§
G3
General-purpose input/output (GPIO) 15 pin (I/O/Z) or PCI reset (I). No function at default.
GP14/PCLK§
F2
GPIO 14 pin (I/O/Z) or PCI clock (I). No function at default.
GP13/PINTA§
G4
GPIO 13 pin (I/O/Z) or PCI interrupt A (O/Z). No function at default.
GP12/PGNT§
J3
I/O/Z
GPIO 12 pin (I/O/Z) or PCI bus grant (I). No function at default.
GP11/PREQ§
F1
I/O/Z
GPIO 11 pin (I/O/Z) or PCI bus request (O/Z). No function at default.
GP10/PCBE3§
L2
GPIO 10 pin (I/O/Z) or PCI command/byte enable 3 (I/O/Z). No function at default.
GP9/PIDSEL§
M3
GPIO 9 pin (I/O/Z) or PCI initialization device select (I). No function at default.
EMIFA (64-bit) CONTROL SIGNALS COMMON TO ALL TYPES OF MEMORY||k
ACE3
L26
O/Z
IPU
EMIFA memory space enables
ACE2
K23
O/Z
IPU
EMIFA memory space enables
Enabled by bits 28 through 31 of the word address
ACE1
K24
O/Z
IPU
Enabled by bits 28 through 31 of the word address
Only one pin is asserted during any external data access
ACE0
K25
O/Z
IPU
Only one pin is asserted during any external data access
ABE7
T23
O/Z
IPU
ABE6
T24
O/Z
IPU
ABE5
R25
O/Z
IPU
EMIFA byte-enable control
Decoded from the low-order address bits. The number of address bits or byte enables
ABE4
R26
O/Z
IPU
EMIFA byte-enable control
Decoded from the low-order address bits. The number of address bits or byte enables
used depends on the width of external memory.
ABE3
M25
O/Z
IPU
used depends on the width of external memory.
Byte-write enables for most types of memory
ABE2
M26
O/Z
IPU
Byte-write enables for most types of memory
Can be directly connected to SDRAM read and write mask signal (SDQM)
ABE1
L23
O/Z
IPU
Can be directly connected to SDRAM read and write mask signal (SDQM)
ABE0
L24
O/Z
IPU
APDT
M22
O/Z
IPU
EMIFA peripheral data transfer, allows direct transfer between external peripherals
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground
IPD = Internal pulldown, IPU = Internal pullup. (These IPD/IPU signal pins feature a 30-k IPD or IPU resistor. To pull up a signal to the opposite
supply rail, a 1-k
resistor should be used.)
§ For the C6415T and C6416T devices, these pins are multiplexed pins. For more details, see the Device Configurations section of this data sheet.
The C6414T device does not support the PCI or UTOPIA peripherals; therefore, these muxed peripheral pins are standalone peripheral functions
for this device.
|| These C64x devices have two EMIFs (64-bit EMIFA and 16-bit EMIFB). The prefix “A” in front of a signal name indicates it is an EMIFA signal
whereas a prefix “B” in front of a signal name indicates it is an EMIFB signal. Throughout the rest of this document, in generic EMIF areas of
discussion, the prefix “A” or “B” may be omitted from the signal name.
kTo maintain signal integrity for the EMIF signals, serial termination resistors should be inserted into all EMIF output signal lines.
相关PDF资料
PDF描述
GMA50DTBH CONN EDGECARD 100PS R/A .125 SLD
TPSB336K010A0500 CAP TANT 33UF 10V 10% 1210
MAX6501UKP065+T IC TEMP SWITCH SOT23-5
VE-BNY-CY-F3 CONVERTER MOD DC/DC 3.3V 33W
TPSB336K010A0425 CAP TANT 33UF 10V 10% 1210
相关代理商/技术参数
参数描述
TMS320C6416TGLZ1 制造商:TI 制造商全称:Texas Instruments 功能描述:FIXED-POINT DIGITAL SIGNAL PROCESSORS
TMS320C6416TGLZ6 制造商:Rochester Electronics LLC 功能描述:FIXED-POINT DIGITAL SIGNAL PROCESSOR - Bulk 制造商:Texas Instruments 功能描述:
TMS320C6416TGLZ7 制造商:Rochester Electronics LLC 功能描述:FIXED-POINT DIGITAL SIGNAL PROCESSOR - Bulk 制造商:Texas Instruments 功能描述:
TMS320C6416TGLZ8 制造商:Rochester Electronics LLC 功能描述: 制造商:Texas Instruments 功能描述:
TMS320C6416TGLZA6 制造商:Rochester Electronics LLC 功能描述:FIXED-POINT DIGITAL SIGNAL PROCESSOR - Bulk 制造商:Texas Instruments 功能描述:
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*