- 您现在的位置：买卖IC网 > PDF目录19987 > TPS23757PW (Texas Instruments)IC CTRLR POE PD IEEE 20TSSOP PDF资料下载
参数资料
| 型号： | TPS23757PW |
| 厂商： | Texas Instruments |
| 文件页数： | 18/39页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR POE PD IEEE 20TSSOP |
| 标准包装： | 70 |
| 类型： | 以太网供电开关（PoE） |
| 应用： | 远程外设（工业控制，相机，数据访问） |
| 内部开关： | 是 |
| 电流限制： | 465mA |
| 电源电压： | 0 V ~ 57 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 20-TSSOP |
| 包装： | 管件 |
| 产品目录页面： | 1012 (CN2011-ZH PDF) |
| 其它名称： | 296-24949-5 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页
TPS23757
SLVS948D – JULY 2009 – REVISED NOVEMBER 2013
www.ti.com
Inrush and Startup
The TPS23757 provides a 140 mA inrush limit that is compatible with both type 1 and type 2 PSEs. The
TPS23757’s internal softstart permits control of the converter startup preventing the converter from exceeding the
PSE output limitations. APb becomes valid within t APb after converter switching starts, or if an adapter is plugged
in while the PD is operating from a PSE.
Maintain Power Signature
The MPS is an electrical signature presented by the PD to assure the PSE that it is still present after operating
voltage is applied. A valid MPS consists of a minimum dc current of 10 mA (or a 10 mA pulsed current for at
least 75 ms every 325 ms) and an ac impedance lower than 26.3 k ? in parallel with 0.05 μ F. The ac impedance
is usually accomplished by the minimum operating C IN requirement of 5 μ F. When either APD or DEN is used to
force the hotswap switch off, the dc MPS will not be met. A PSE that monitors the dc MPS will remove power
from the PD when this occurs. A PSE that monitors only the ac MPS may remove power from the PD.
Startup and Converter Operation
The internal PoE UVLO (Under Voltage Lock Out) circuit holds the hotswap switch off before the PSE provides
full voltage to the PD. This prevents the converter circuits from loading the PoE input during detection and
classification. The converter circuits will discharge C IN , C VC , and C VB while the PD is unpowered. Thus V VDD -V RTN
will be a small voltage just after full voltage is applied to the PD, as seen in Figure 20 . The PSE drives the PI
voltage to the operating range once it has decided to power up the PD. When V VDD rises above the UVLO turn-
on threshold (V UVLO-R , ~35 V) with RTN high, the TPS23757 enables the hotswap MOSFET with a ~140 mA
(inrush) current limit as seen in Figure 21 . Converter switching is disabled while C IN charges and V RTN falls from
V VDD to nearly V VSS , however the converter startup circuit is allowed to charge C VC (the bootstrap startup
capacitor). Additional loading applied between V VDD and V RTN during the inrush state may prevent successful PD
and subsequent converter start up. Converter switching is allowed if the PD is not in inrush, converter OTSD
(over-temperature shutdown) is not active, and the V C UVLO permits it. Once the inrush current falls about 10%
below the inrush current limit, the PD current limit switches to the operational level (~450 mA). Continuing the
startup sequence shown in Figure 21 , V VC continues to rise until the startup threshold (V CUV , ~9 V) is exceeded,
turning the startup source off and enabling switching. The V B regulator is always active, powering the internal
converter circuits as V VC rises. There is a slight delay between the removal of charge current and the start of
switching as the softstart ramp sweeps above the V ZDC threshold. V VC falls as it powers both the internal circuits
and the switching MOSFET gates. If the converter control bias output rises to support V VC before it falls to V CUV –
V CUVH ( ~5.5 V), a successful startup occurs. APb in Figure 21 becomes active within t APb from the start of
switching, indicating that an adapter is plugged in.
V APb RTN
10 V/div
100 mA/div
10 V/div
2 V/div
50 V/div
-V
I PI
V VC - V RTN
V OUT
V VDD - V RTN
Inrush
PI Powered
Switching Starts
t - Time - 10 ms/div
Figure 21. Power Up and Start
18
Submit Documentation Feedback
Copyright ? 2009–2013, Texas Instruments Incorporated
相关PDF资料 |
PDF描述 |
|---|---|
| R2S8-0509/P | CONV DC/DC 2W 5VIN 9VOUT SMD |
| 5650090-1 | AMP .050 CL CEC 56 DUAL POS |
| GRM188R71H471KA01D | CAP CER 470PF 50V 10% X7R 0603 |
| VE-J5V-CY-B1 | CONVERTER MOD DC/DC 5.8V 50W |
| ISL9021AIRUKZ-T7A | IC REG LDO 2.85V .25A 6UTDFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TPS23757PWR | 功能描述:热插拔功率分布 Hi Eff PoE Interface & DC/DC Controller RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| TPS2375D | 功能描述:热插拔功率分布 IEEE 802.3af PoE Pwr Device Cntrler RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| TPS2375D | 制造商:Texas Instruments 功能描述:POWER OVER ETHERNET ((NW)) |
| TPS2375DG4 | 功能描述:热插拔功率分布 IEEE 802.3af PoE Pwr Device Cntrler RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| TPS2375DR | 功能描述:热插拔功率分布 IEEE 802.3af PoE Pwr Device Cntrler RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。