- 您现在的位置：买卖IC网 > PDF目录19987 > TPS23757PW (Texas Instruments)IC CTRLR POE PD IEEE 20TSSOP PDF资料下载
参数资料
| 型号： | TPS23757PW |
| 厂商： | Texas Instruments |
| 文件页数： | 20/39页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR POE PD IEEE 20TSSOP |
| 标准包装： | 70 |
| 类型： | 以太网供电开关（PoE） |
| 应用： | 远程外设（工业控制，相机，数据访问） |
| 内部开关： | 是 |
| 电流限制： | 465mA |
| 电源电压： | 0 V ~ 57 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 20-TSSOP |
| 包装： | 管件 |
| 产品目录页面： | 1012 (CN2011-ZH PDF) |
| 其它名称： | 296-24949-5 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页当前第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页
TPS23757
SLVS948D – JULY 2009 – REVISED NOVEMBER 2013
www.ti.com
Converter Controller Features
The TPS23757 dc/dc controller implements a typical current-mode control as shown in the Functional Block
Diagram. Features include oscillator, overcurrent and PWM comparators, current-sense blanker, dead-time
control, softstart, and gate driver. In addition, an internal slope-compensation ramp generator, frequency
synchronization logic, thermal shutdown, and startup current source with control are provided.
The TPS23757 is optimized for isolated converters, and does not provide an internal error amplifier. Instead, the
optocoupler feedback is directly fed to the CTL pin which serves as a current-demand control for the PWM.
There is an offset of V ZDC (~1.5 V) and 2:1 resistor divider between the CTL pin and the PWM. A V CTL below
V ZDC will stop converter switching, while voltages above (V ZDC + (2 × V CSMAX )) will not increase the requested
peak current in the switching MOSFET. Optocoupler biasing design is eased by this limited control range.
Bootstrap Topology
The internal startup current source and control logic implement a bootstrap-type startup as discussed in Startup
and Converter Operation . The startup current source charges C VC from V DD1 when the converter is disabled
(either by the PD control or the V C control) to store enough energy to start the converter. Steady-state operating
power must come from a converter (bias winding) output or other source. Loading on V C and V B must be minimal
while C VC charges, otherwise the converter may never start. The optocoupler will not load V B when the converter
is off for most situations, however care should be taken in ORing topologies where the output is powered when
PoE is off.
The converter will shut off when V C falls below its lower UVLO. This can happen when power is removed from
the PD, or during a fault on a converter output rail. When one output is shorted, all the output voltages fall
including the one that powers V C . The control circuit discharges V C until it hits the lower UVLO and turns off. A
restart will initiate as described in Startup and Converter Operation if the converter turns off and there is sufficient
V DD1 voltage. This type of operation is sometimes referred to as hiccup mode which provides robust output short
protection by providing time-average heating reduction of the output rectifier.
The bootstrap control logic disables most of the converter controller circuits except the V B regulator and internal
reference. Both GATE and GAT2 (assuming GAT2 is enabled) will be low when the converter is disabled. FRS,
BLNK, and DT will be at ARTN while the V C UVLO disables the converter. While the converter runs, FRS, BLNK,
and DT will be about 1.25 V.
The startup current source transitions to a resistance as (V VDD1 – V VC ) falls below 7 V, but will start the converter
from adapters within t ST . The lower test voltage for t ST was chosen based on an assumed adapter tolerance, but
is not meant to imply a hard cutoff exists. Startup takes longer and eventually will not occur as V DD1 decreases
below the test voltage. The bootstrap source provides reliable startup from widely varying input voltages, and
eliminates the continual power loss of external resistors. The startup current source will not charge above the
maximum recommended V VC if the converter is disabled and there is sufficient V DD1 to charge higher.
Current Slope Compensation and Current Limit
Current-mode control requires addition of a compensation ramp to the sensed inductive (transformer or inductor)
current for stability at duty cycles near and over 50%. The TPS23757 has a maximum duty cycle limit of 78%,
permitting the design of wide input-range flyback and active clamp converters with a lower voltage stress on the
output rectifiers. While the maximum duty cycle is 78%, converters may be designed that run at duty cycles well
below this for a narrower, 36 V to 57 V PI range. The TPS23757 provides a fixed internal compensation ramp
that suffices for most applications.
The TPS23757 provides internal, frequency independent, slope compensation (150 mV, V SLOPE ) to the PWM
comparator input for current-mode control-loop stability. This voltage is not applied to the current-limit comparator
whose threshold is 0.55 V (V CSMAX ). If the provided slope is not sufficient, the effective slope may be increased
by addition of R S per Figure 26 . The additional slope voltage is provided by (I SL-EX × R S ). There is also a small dc
offset caused by the ~2.5 μ A pin current. The peak current limit does not have duty cycle dependency unless R S
is used. This makes it easier to design the current limit to a fixed value. See Current Slope Compensation for
more information.
The internal comparators monitoring CS are isolated from the IC pin by the blanking circuits while GATE is low,
and for a short time (blanking period) just after GATE switches high. A 440 ? (max) equivalent pull down on CS
is applied while GATE is low.
20
Submit Documentation Feedback
Copyright ? 2009–2013, Texas Instruments Incorporated
相关PDF资料 |
PDF描述 |
|---|---|
| R2S8-0509/P | CONV DC/DC 2W 5VIN 9VOUT SMD |
| 5650090-1 | AMP .050 CL CEC 56 DUAL POS |
| GRM188R71H471KA01D | CAP CER 470PF 50V 10% X7R 0603 |
| VE-J5V-CY-B1 | CONVERTER MOD DC/DC 5.8V 50W |
| ISL9021AIRUKZ-T7A | IC REG LDO 2.85V .25A 6UTDFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TPS23757PWR | 功能描述:热插拔功率分布 Hi Eff PoE Interface & DC/DC Controller RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| TPS2375D | 功能描述:热插拔功率分布 IEEE 802.3af PoE Pwr Device Cntrler RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| TPS2375D | 制造商:Texas Instruments 功能描述:POWER OVER ETHERNET ((NW)) |
| TPS2375DG4 | 功能描述:热插拔功率分布 IEEE 802.3af PoE Pwr Device Cntrler RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| TPS2375DR | 功能描述:热插拔功率分布 IEEE 802.3af PoE Pwr Device Cntrler RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。