参数资料
型号: TPS23757PW
厂商: Texas Instruments
文件页数: 23/39页
文件大小: 0K
描述: IC CTRLR POE PD IEEE 20TSSOP
标准包装: 70
类型: 以太网供电开关(PoE)
应用: 远程外设(工业控制,相机,数据访问)
内部开关:
电流限制: 465mA
电源电压: 0 V ~ 57 V
工作温度: -40°C ~ 125°C
安装类型: 表面贴装
封装/外壳: 20-TSSOP(0.173",4.40mm 宽)
供应商设备封装: 20-TSSOP
包装: 管件
产品目录页面: 1012 (CN2011-ZH PDF)
其它名称: 296-24949-5

TPS23757
www.ti.com
SLVS948D – JULY 2009 – REVISED NOVEMBER 2013
Several examples will demonstrate the limitations inherent in ORing solutions. Diode ORing a 48 V adapter with
PoE (option 1) presents the problem that either source might be higher. A blocking switch would be required to
assure which source was active. A second example is combining a 12 V adapter with PoE using option 2. The
converter will draw approximately four times the current at 12 V from the adapter than it does from PoE at 48 V.
Transition from adapter power to PoE may demand more current than can be supplied by the PSE. The
converter must be turned off while C IN capacitance charges, with a subsequent converter restart at the higher
voltage and lower input current. A third example is use of a 12 V adapter with ORing option 1. The PD hotswap
would have to handle four times the current, and have 1/16 the resistance (be 16 times larger) to dissipate equal
power. A fourth example is that MPS is lost when running from the adapter, causing the PSE to remove power
from the PD. If ac power is then lost, the PD will stop operating until the PSE detects and powers the PD.
APPLICATION INFORMATION
The TPS23757 will support many power supply topologies that require a single PWM gate drive or two
complementary gate drives and will operate with current-mode control. Figure 1 provides an example of a flyback
with a driven output synchronous rectifier. The TPS23757 may be used in topologies that do not require GAT2,
which may be disabled to reduce its idling loss.
Selecting a converter topology along with a design procedure is beyond the scope of this applications section.
Examples to help in programming the TPS23757 are shown below. Additional special topics are included to
explain the ORing capabilities, frequency dithering, and other design considerations.
For more specific converter design examples refer to the following application notes:
?
?
?
?
Designing with the TPS23753 Powered Device and Power Supply Controller, SLVA305
Understanding and Designing an Active Clamp Current Mode Controlled Converter Using the UCC2897A.
SLUA535
Advanced Adapter ORing Solutions using the TPS23753, SLVA306A
TPS23757EVM: Evaluation Module for TPS23757, SLVU318
Input Bridges and Schottky Diodes
Using Schottky diodes instead of PN junction diodes for the PoE input bridges and D VDD will reduce the loss of
this function by about 30%. There are however some things to consider when using them.
The IEEE standard specifies a maximum backfeed voltage of 2.8 V . A 100 k ? resistor is placed between the
unpowered pairs and the voltage is measured across the resistor. Schottky diodes often have a higher reverse
leakage current than PN diodes, making this a harder requirement to meet. Use conservative design for diode
operating temperature, select lower-leakage devices where possible, and match leakage and temperatures by
using packaged bridges to help with this.
Schottky diode leakage current and lower dynamic resistance can impact the detection signature. Setting
reasonable expectations for the temperature range over which the detection signature is accurate is the simplest
solution. Increasing R DEN slightly may also help meet the requirement.
Schottky diodes have proven less robust to the stresses of ESD transients, failing as a short or becoming leaky.
Care must be taken to provide adequate protection in line with the exposure levels. This protection may be as
simple as ferrite beads and capacitors.
A general recommendation for the input rectifiers are 1 A or 2 A, 100 V rated discrete or bridge diodes.
Protection, D1
A TVS, D 1 , across the rectified PoE voltage per Figure 24 must be used. An SMAJ58A, or a part with equal to or
better performance, is recommended for general indoor applications. If an adapter is connected from V DD1 to
RTN, as in ORing option 2 above, voltage transients caused by the input cable inductance ringing with the
internal PD capacitance can occur. Adequate capacitive filtering or a TVS must limit this voltage to be within the
absolute maximum ratings. Outdoor transient levels or special applications require additional protection.
Copyright ? 2009–2013, Texas Instruments Incorporated
Submit Documentation Feedback
23
相关PDF资料
PDF描述
R2S8-0509/P CONV DC/DC 2W 5VIN 9VOUT SMD
5650090-1 AMP .050 CL CEC 56 DUAL POS
GRM188R71H471KA01D CAP CER 470PF 50V 10% X7R 0603
VE-J5V-CY-B1 CONVERTER MOD DC/DC 5.8V 50W
ISL9021AIRUKZ-T7A IC REG LDO 2.85V .25A 6UTDFN
相关代理商/技术参数
参数描述
TPS23757PWR 功能描述:热插拔功率分布 Hi Eff PoE Interface & DC/DC Controller RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube
TPS2375D 功能描述:热插拔功率分布 IEEE 802.3af PoE Pwr Device Cntrler RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube
TPS2375D 制造商:Texas Instruments 功能描述:POWER OVER ETHERNET ((NW))
TPS2375DG4 功能描述:热插拔功率分布 IEEE 802.3af PoE Pwr Device Cntrler RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube
TPS2375DR 功能描述:热插拔功率分布 IEEE 802.3af PoE Pwr Device Cntrler RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube