收藏本站
参数资料
型号： TPS24713DGSR
厂商： TEXAS INSTRUMENTS INC
元件分类： 电源管理
英文描述： POWER SUPPLY SUPPORT CKT, PDSO10
封装： GREEN, PLASTIC, MSOP-10
文件页数： 19/34页
文件大小： 2148K
代理商： TPS24713DGSR
GATE
ISS
VCC
t
C
I
C
V
D
=
-
÷
è
Partof
TPS2471x
M
1
ToLoad
GND
GATE
FromSource
R
GATE
1k
C
GATE
S0509-02
I
30 A
GATE
TPS24710, TPS24711
TPS24712, TPS24713
SLVSAL2C
– JANUARY 2011 – REVISED MAY 2011
www.ti.com
(14)
Figure 36. Gate Capacitor (dV/dt) Control Inrush Mode.
ADDITIONAL DESIGN CONSIDERATIONS
Use of PG/PGb
Use the PG/PGb pin to control and coordinate a downstream dc/dc converter. If this is not done, then a long time
delay is needed to allow COUT to fully charge before the converter starts. An undesirable latch-up condition can
be created between the TPS24710/11/12/13 output characteristic and the dc/dc converter input characteristic if
the converter starts while COUT is still charging; the PG/PGb pin is one way to avoid this
Output Clamp Diode
Inductive loads on the output may drive the OUT pin below GND when the circuit is unplugged or during a
current-limit event. The OUT pin ratings can be satisfied by connecting a diode from OUT to GND. The diode
should be selected to control the negative voltage at the full short-circuit current. Schottky diodes are generally
recommended for this application.
Gate Clamp Diode
The TPS24710/11/12/13 has a relatively well-regulated gate voltage of 12 V to 15.5 V with a supply voltage VVCC
higher than 4 V. A small clamp Zener from gate to source of M1 is recommended if VGS of M1 is rated below 12
V. A series resistance of several hundred ohms or a series silicon diode is recommended to prevent the output
capacitance from discharging through the gate driver to ground.
High-Gate-Capacitance Applications
Gate voltage overstress and abnormally large fault current spikes can be caused by large gate capacitance. An
external gate clamp Zener diode is recommended to assist the internal Zener if the total gate capacitance of M1
exceeds about 4000 pF. When gate capacitor dV/dt control is used, a 1-k
Ω resistor in series with CGATE is
recommended (see Figure 36). If the series R-C combination is used for MOSFETs with CISS less than 3000 pF,
then a Zener diode is not necessary.
26
Submit Documentation Feedback
Copyright
2011, Texas Instruments Incorporated
Product Folder Link(s): TPS24710 TPS24711 TPS24712 TPS24713
相关PDF资料
PDF描述
TC151A3112EOA713 0.25 A SWITCHING REGULATOR, 50 kHz SWITCHING FREQ-MAX, PDSO8
TC151A5431EOA723 0.25 A SWITCHING REGULATOR, 50 kHz SWITCHING FREQ-MAX, PDSO8
TC151B5433EOA713 0.25 A SWITCHING REGULATOR, 50 kHz SWITCHING FREQ-MAX, PDSO8
TC151A4634EOA723 0.25 A SWITCHING REGULATOR, 50 kHz SWITCHING FREQ-MAX, PDSO8
TC151A3537EOA713 0.25 A SWITCHING REGULATOR, 50 kHz SWITCHING FREQ-MAX, PDSO8
相关代理商/技术参数
参数描述
TPS24720EVM-001 功能描述:电源管理IC开发工具 TPS24720 Eval Mod RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V
TPS24720RGTR 功能描述:热插拔功率分布 2.5-18V Hi Eff Adj Ltd Hot-Swap Cntrlr RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube
TPS24720RGTT 功能描述:热插拔功率分布 2.5-18V Hi Eff Adj Ltd Hot-Swap Cntrlr RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube
TPS24740EVM-596 功能描述:IC CTRLR HOT SWAP 2.5-18V 16QFN 制造商:texas instruments 系列:- 零件状态:在售 主要用途:电源管理，热交换控制器 嵌入式:- 使用的 IC/零件:TPS24740 主要属性:- 辅助属性:- 所含物品:板 标准包装:1
TPS24740RGET 功能描述:Hot Swap Controller, OR Controller 1 Channel General Purpose 24-VQFN (4x4) 制造商:texas instruments 系列:- 包装:剪切带（CT） 零件状态:有效 类型:热交换控制器，OR 控制器 通道数:1 内部开关:无 应用:通用 特性:闭锁故障，UVLO 可编程特性:限流，故障超时，OVP，开启电压 电压 - 电源:2.5 V ~ 18 V 电流 - 输出（最大值）:- 工作温度:-40°C ~ 125°C 电流 - 电源:4.2mA 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商器件封装:24-VQFN（4x4） 功能引脚:ENHS，ENOR，FLTb，FSTP，IMON，IMONBUF，OV，PGHS，PLIM，RVSNP，RVSNM，SENM，SET，STAT，TFLT，TINR 标准包装:1
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*