- 您现在的位置：买卖IC网 > PDF目录136952 > TPS24713DGSR (TEXAS INSTRUMENTS INC) POWER SUPPLY SUPPORT CKT, PDSO10 PDF资料下载
参数资料
| 型号： | TPS24713DGSR |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 电源管理 |
| 英文描述： | POWER SUPPLY SUPPORT CKT, PDSO10 |
| 封装： | GREEN, PLASTIC, MSOP-10 |
| 文件页数： | 32/34页 |
| 文件大小： | 2148K |
| 代理商： | TPS24713DGSR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页当前第32页第33页第34页
SLVSAL2C
– JANUARY 2011 – REVISED MAY 2011
PIN FUNCTIONS (continued)
PINS
NAME
I/O
DESCRIPTION
TPS24710/11 TPS24712/13
Active-high, open-drain power good indicator. Status is determined by the voltage
PG
-
1
across the MOSFET.
O
Active-low, open-drain power good indicator. Status is determined by the voltage
PGb
1
-
across the MOSFET.
Power-limiting programming pin. A resistor from this pin to GND sets the maximum
PROG
3
I
power dissipation for the FET.
SENSE
8
I
Current sensing input for resistor shunt from VCC to SENSE.
TIMER
4
I/O
A capacitor connected from this pin to GND provides a fault timing function.
VCC
9
I
Input-voltage sense and power supply
DETAILED PIN DESCRIPTIONS
The following description relies on the typical application diagram on the front page of this data sheet, as well as
the functional block diagram in Figure 4.
EN: Applying a voltage of 1.35 V or more to this pin enables the gate driver. The addition of an external resistor
divider allows the EN pin to serve as an undervoltage monitor. Cycling EN low and then back high resets the
TPS24710/11/12/13 that has latched off due to a fault condition. This pin should not be left floating.
FLT: FLT is assigned for TPS24712/13. This active-high open-drain output assumes high-impedance when
TPS24712/13 has remained in current limit long enough for the fault timer to expire. The behavior of the FLT pin
depends on the version of the IC. The TPS24712 operates in latch mode and the TPS24713 operates in retry
mode. In latch mode, a fault timeout disables the external MOSFET and holds FLT in open drain condition. The
latched mode of operation is reset by cycling EN or VCC. In retry mode, a fault timeout first disables the external
MOSFET, next waits sixteen cycles of TIMER charging and discharging, and finally attempts a restart. This
process repeats as long as the fault persists. In retry mode, the FLT pin goes open-drain whenever the external
MOSFET is disabled by the fault timer. In a sustained fault, the FLT waveform becomes a train of pulses. The
FLT pin does not assert if the external MOSFET is disabled by EN, overtemperature shutdown, or UVLO. This
pin can be left floating when not used.
FLTb: FLTb is assigned for TPS24710/11. This active-low open-drain output pulls low when TPS24710/11/12/13
has remained in current limit long enough for the fault timer to expire. The behavior of the FLTb pin depends on
the version of the IC. The TPS24710 operates in latch mode and the TPS24711 operates in retry mode. In latch
mode, a fault timeout disables the external MOSFET and holds FLTb low. The latched mode of operation is reset
by cycling EN or VCC. In retry mode, a fault timeout first disables the external MOSFET, next waits sixteen
cycles of TIMER charging and discharging, and finally attempts a restart. This process repeats as long as the
fault persists. In retry mode, the FLTb pin is pulled low whenever the external MOSFET is disabled by the fault
timer. In a sustained fault, the FLTb waveform becomes a train of pulses. The FLTb pin does not assert if the
external MOSFET is disabled by EN, overtemperature shutdown, or UVLO. This pin can be left floating when not
used.
GATE: This pin provides gate drive to the external MOSFET. A charge pump sources 30
A to enhance the
external MOSFET. A 13.9-V clamp between GATE and VCC limits the gate-to-source voltage, because VVCC is
very close to VOUT in normal operation. During start-up, a transconductance amplifier regulates the gate voltage
of M1 to provide inrush current limiting. The TIMER pin charges timer capacitor CT during the inrush. Inrush
current limiting continues until the V(GATE – VCC) exceeds the Timer Activation Voltage (6 V for VVCC = 12 V). Then
the TPS24710/11/12/13 enters into circuit-breaker mode. The Timer Activation Voltage is defined as a threshold
voltage. When V(GATE-VCC) exceeds this threshold voltage, the inrush operation is finished and the TIMER stops
sourcing current and begins sinking current. In the circuit-breaker mode, the current flowing in RSENSE is
compared with the current-limit threshold derived from the MOSFET power-limit scheme (see PROG). If the
current flowing in RSENSE exceeds the current limit threshold, then MOSFET M1 is turned off. The GATE pin is
disabled by the following three conditions:
1. GATE is pulled down by an 11-mA current source when
– The fault timer expires during an overload current fault (VSENSE > 25 mV)
– VEN is below its falling threshold
Copyright
2011, Texas Instruments Incorporated
7
相关PDF资料 |
PDF描述 |
|---|---|
| TC151A3112EOA713 | 0.25 A SWITCHING REGULATOR, 50 kHz SWITCHING FREQ-MAX, PDSO8 |
| TC151A5431EOA723 | 0.25 A SWITCHING REGULATOR, 50 kHz SWITCHING FREQ-MAX, PDSO8 |
| TC151B5433EOA713 | 0.25 A SWITCHING REGULATOR, 50 kHz SWITCHING FREQ-MAX, PDSO8 |
| TC151A4634EOA723 | 0.25 A SWITCHING REGULATOR, 50 kHz SWITCHING FREQ-MAX, PDSO8 |
| TC151A3537EOA713 | 0.25 A SWITCHING REGULATOR, 50 kHz SWITCHING FREQ-MAX, PDSO8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TPS24720EVM-001 | 功能描述:电源管理IC开发工具 TPS24720 Eval Mod RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| TPS24720RGTR | 功能描述:热插拔功率分布 2.5-18V Hi Eff Adj Ltd Hot-Swap Cntrlr RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| TPS24720RGTT | 功能描述:热插拔功率分布 2.5-18V Hi Eff Adj Ltd Hot-Swap Cntrlr RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| TPS24740EVM-596 | 功能描述:IC CTRLR HOT SWAP 2.5-18V 16QFN 制造商:texas instruments 系列:- 零件状态:在售 主要用途:电源管理，热交换控制器 嵌入式:- 使用的 IC/零件:TPS24740 主要属性:- 辅助属性:- 所含物品:板 标准包装:1 |
| TPS24740RGET | 功能描述:Hot Swap Controller, OR Controller 1 Channel General Purpose 24-VQFN (4x4) 制造商:texas instruments 系列:- 包装:剪切带（CT） 零件状态:有效 类型:热交换控制器，OR 控制器 通道数:1 内部开关:无 应用:通用 特性:闭锁故障，UVLO 可编程特性:限流，故障超时，OVP，开启电压 电压 - 电源:2.5 V ~ 18 V 电流 - 输出（最大值）:- 工作温度:-40°C ~ 125°C 电流 - 电源:4.2mA 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商器件封装:24-VQFN（4x4） 功能引脚:ENHS，ENOR，FLTb，FSTP，IMON，IMONBUF，OV，PGHS，PLIM，RVSNP，RVSNM，SENM，SET，STAT，TFLT，TINR 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。