参数资料
| 型号： | TPS54260DRCR |
| 厂商： | Texas Instruments |
| 文件页数： | 11/52页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK ADJ 2.5A 10SON |
| 标准包装： | 3,000 |
| 系列： | SWIFT™, Eco-Mode™ |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 0.8 V ~ 58 V |
| 输入电压： | 3.5 V ~ 60 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 100kHz ~ 2.5MHz |
| 电流 - 输出： | 2.5A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 150°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-VFDFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 10-SON 裸露焊盘（3x3） |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页
www.ti.com
SLVSA86A – MARCH 2010 – REVISED DECEMBER 2010
OVERVIEW
The TPS54260 device is a 60-V, 2.5-A, step-down (buck) regulator with an integrated high side n-channel
MOSFET. To improve performance during line and load transients the device implements a constant frequency,
current mode control which reduces output capacitance and simplifies external frequency compensation design.
The wide switching frequency of 100kHz to 2500kHz allows for efficiency and size optimization when selecting
the output filter components. The switching frequency is adjusted using a resistor to ground on the RT/CLK pin.
The device has an internal phase lock loop (PLL) on the RT/CLK pin that is used to synchronize the power
switch turn on to a falling edge of an external system clock.
The TPS54260 has a default start up voltage of approximately 2.5V. The EN pin has an internal pull-up current
source that can be used to adjust the input voltage under voltage lockout (UVLO) threshold with two external
resistors. In addition, the pull up current provides a default condition. When the EN pin is floating the device will
operate. The operating current is 138 m A when not switching and under no load. When the device is disabled, the
supply current is 1.3 m A.
The integrated 200m ? high side MOSFET allows for high efficiency power supply designs capable of delivering
2.5 amperes of continuous current to a load. The TPS54260 reduces the external component count by
integrating the boot recharge diode. The bias voltage for the integrated high side MOSFET is supplied by a
capacitor on the BOOT to PH pin. The boot capacitor voltage is monitored by an UVLO circuit and will turn the
high side MOSFET off when the boot voltage falls below a preset threshold. The TPS54260 can operate at high
duty cycles because of the boot UVLO. The output voltage can be stepped down to as low as the 0.8V
reference.
The TPS54260 has a power good comparator (PWRGD) which asserts when the regulated output voltage is less
than 92% or greater than 109% of the nominal output voltage. The PWRGD pin is an open drain output which
deasserts when the VSENSE pin voltage is between 94% and 107% of the nominal output voltage allowing the
pin to transition high when a pull-up resistor is used.
The TPS54260 minimizes excessive output overvoltage (OV) transients by taking advantage of the OV power
good comparator. When the OV comparator is activated, the high side MOSFET is turned off and masked from
turning on until the output voltage is lower than 107%.
The SS/TR (slow start/tracking) pin is used to minimize inrush currents or provide power supply sequencing
during power up. A small value capacitor should be coupled to the pin to adjust the slow start time. A resistor
divider can be coupled to the pin for critical power supply sequencing requirements. The SS/TR pin is discharged
before the output powers up. This discharging ensures a repeatable restart after an over-temperature fault,
UVLO fault or a disabled condition.
The TPS54260, also, discharges the slow start capacitor during overload conditions with an overload recovery
circuit. The overload recovery circuit will slow start the output from the fault voltage to the nominal regulation
voltage once a fault condition is removed. A frequency foldback circuit reduces the switching frequency during
startup and overcurrent fault conditions to help control the inductor current.
Copyright ? 2010, Texas Instruments Incorporated
Product Folder Link(s): TPS54260
11
相关PDF资料 |
PDF描述 |
|---|---|
| TPS54326RGTT | IC REG BUCK SYNC ADJ 3A 16QFN |
| TPS54478RTER | IC REG BUCK SYNC ADJ 4A 16WQFN |
| TPS54550PWPG4 | IC REG BUCK SYNC ADJ 6A 16HTSSOP |
| TPS54678RTER | IC REG BUCK SYNC ADJ 6A 16WQFN |
| TPS54900PWRG4 | IC REG BUCK ADJ .1A QUAD 16TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TPS54260DRCT | 功能描述:直流/直流开关转换器 3.5V-60Vin,2.5A,2.5 MHz Step Down SWIFT RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| TPS54260EVM-597 | 功能描述:电源管理IC开发工具 2.5A,10.8-13.2Vin SWIFT Conv Eval Mod RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| TPS54260MDGQTEP | 功能描述:IC REG BUCK ADJ 2.5A 10MOSP 制造商:texas instruments 系列:Eco-Mode? 包装:剪切带（CT） 零件状态:在售 功能:降压 输出配置:正 拓扑:降压 输出类型:可调式 输出数:1 电压 - 输入（最小值）:3.5V 电压 - 输入（最大值）:60V 电压 - 输出（最小值/固定）:0.8V 电压 - 输出（最大值）:60V 电流 - 输出:2.5A 频率 - 开关:100kHz ~ 2.5MHz 同步整流器:无 工作温度:-40°C ~ 150°C（TJ） 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 供应商器件封装:10-MSOP-PowerPad 标准包装:1 |
| TPS54260MDRCTEP | 功能描述:IC REG BUCK ADJ 2.5A 10VSON 制造商:texas instruments 系列:Eco-Mode? 包装:剪切带（CT） 零件状态:在售 功能:降压 输出配置:正 拓扑:降压 输出类型:可调式 输出数:1 电压 - 输入（最小值）:3.5V 电压 - 输入（最大值）:60V 电压 - 输出（最小值/固定）:0.8V 电压 - 输出（最大值）:60V 电流 - 输出:2.5A 频率 - 开关:100kHz ~ 2.5MHz 同步整流器:无 工作温度:-40°C ~ 150°C（TJ） 安装类型:表面贴装 封装/外壳:10-VFDFN 裸露焊盘 供应商器件封装:10-VSON（3x3） 标准包装:1 |
| TPS54260-Q1 | 制造商:TI 制造商全称:Texas Instruments 功能描述:3.5 V to 60 V STEP DOWN CONVERTER WITH ECO-MODEa?￠ |
发布紧急采购，3分钟左右您将得到回复。