收藏本站
参数资料
型号： TPS65072TRSLRQ1
厂商： TEXAS INSTRUMENTS INC
元件分类： 电源管理
英文描述： POWER SUPPLY SUPPORT CKT, PQCC48
封装： 6 X 6 MM, 0.4 MM PITCH, PLASTIC, QFN-48
文件页数： 32/90页
文件大小： 1375K
代理商： TPS65072TRSLRQ1
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
SLVSAP7 – JANUARY 2011
www.ti.com
Table 3. TSC Equations
MEASUREMENT
CHANNEL
EQUATION
X Plate resistance
AD_IN14
Rx = VTSREF/ [(VADC / 22k) × 150]
Y plate resistance
AD_IN14
Ry = VTSREF / [(VADC / 22k) × 150]
X position
AD_IN14
Xpos = Rx2 / (Rx1 + Rx2) = Rx2 / Rx
Rx2 = VADC x Rx/ VTSREF; Rx1 = Rx – Rx2
Xpos = ADRESULT / 1024
Y position
AD_IN14
Ypos = Ry2 / (Ry1 + Ry2) = Ry2 / Ry
Ry2 = VADC x Ry/ VTSREF; Ry1 = Ry – Ry2
Ypos = ADRESULT / 1024
Pressure
AD_IN14
Rc = R – Rx1//Rx2 – Ry1//Ry2
R = VTSREF/ [(VADC / 22k) × 150]
Rx1//Rx2 = Rx × Xpos × (1 – Xpos)
Ry1//Ry2 = Ry × Ypos × (1 – Ypos)
Performing Measurements Using the Touch Screen Controller
In order to take measurements with the touch screen controller, the ADC has to be enabled and configured for
use with the touch screen controller (TSC) first. In case the TSC is planned to be operated interrupt driven, the
TSC needs to be in TSC standby mode per default. Only in TSC standby mode an interrupt is generated based
on a touch of the screen. The TSC should therefore be in this mode until a touch is detected. Afterwards, the
TSC has to be configured for x-position measurement followed by y-position measurement. Now, the TSC can be
set to TSC standby again to wait for the next touch of the screen. For a non-interrupt driven sequence, see
TSCMODE. Register Address: 08h (page 50) in the Registers section. A typical interrupt driven sequence is
given below:
Set TSCMODE to 101 to set TSC to TSC standby, so an interrupt is generated when the screen is touched
Set Bit AD enable = 1 to provide power to the ADC
Set input select for the ADC in register ADCONFIG to 1110 (AD_IN14 selected)
In register INT, set MASK TSC = 1 to unmask the interrupt on a touch of the touch screen
Read Bit TSC INT as it will be set after the TSC has been configured. Reading clears the interrupt.
After a touch was detected, an interrupt is generated by INT pin going LOW
Read Bit TSC INT to clear the interrupt
Set TSCMODE to 000 to select x-position measurement
Start an ADC conversion by setting CONVERSION START =1; wait until END OF CONVERSION = 1
Read register ADRESULT_1 and AD_RESULT_2
Set TSCMODE to 001 to select y-position measurement
Start an ADC conversion by setting CONVERSION START =1; wait until END OF CONVERSION = 1
Read register ADRESULT_1 and AD_RESULT_2
Set TSCMODE to 101 to set TSC to TSC standby again
38
Submit Documentation Feedback
Copyright 2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
相关PDF资料
PDF描述
TC151B4217EOA723 0.25 A SWITCHING REGULATOR, 50 kHz SWITCHING FREQ-MAX, PDSO8
TC151B2419EOA713 0.25 A SWITCHING REGULATOR, 50 kHz SWITCHING FREQ-MAX, PDSO8
TC151A5721EOA723 0.25 A SWITCHING REGULATOR, 50 kHz SWITCHING FREQ-MAX, PDSO8
TC151B1528EOA723 0.25 A SWITCHING REGULATOR, 50 kHz SWITCHING FREQ-MAX, PDSO8
TC151B5830EOA723 0.25 A SWITCHING REGULATOR, 50 kHz SWITCHING FREQ-MAX, PDSO8
相关代理商/技术参数
参数描述
TPS650731EVM-430 功能描述:电源管理IC开发工具 TPS650731 Eval Mod RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V
TPS650731RSLR 功能描述:PMIC 解决方案 5Ch Pwr Mgmt IC RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel
TPS650731RSLT 功能描述:PMIC 解决方案 5Ch Pwr Mgmt IC RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel
TPS650732EVM-430 功能描述:电源管理IC开发工具 TPS650732 Eval Mod RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V
TPS650732RSLR 功能描述:PMIC 解决方案 5Ch Pwr Mgmt IC RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*