- 您现在的位置：买卖IC网 > PDF目录365968 > TSB14AA1 FPGA (Field-Programmable Gate Array) PDF资料下载
参数资料
| 型号： | TSB14AA1 |
| 英文描述： | FPGA (Field-Programmable Gate Array) |
| 中文描述： | 电机及电子学工程师联合会1394-1995。 3.3。 1-port.50/100Mbps。底板PHY |
| 文件页数： | 29/35页 |
| 文件大小： | 224K |
| 代理商： | TSB14AA1 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页当前第29页第30页第31页第32页第33页第34页第35页
6
–
9
6.2.6
Backplane Timing Definitions
Logic Skew
—
The skew between data and strobe within the physical layer itself due to internal skews
between data and strobe logic.
Spatial Skew
—
The skew between data and strobe due to differences in propagation delays along the
transmission line from the arbiter to the transceiver.
Package Skew
—
The propagation delay difference through the transceiver between the data and strobe
channels.
Backplane Skew
—
The skew along the backplane itself due to impedance and/or mismatched data and
strobe line length.
Receive Setup/Hold
—
The setup and hold time needed to latch the incoming data within the PHY arbiter,
based on the recovered clock from Data_Rx and Strb_Rx.
Total Transmit Skew
—
The total skew between data and strobe in transmitting data from the PHY out to the
bus. This is given by the following equation:
Total Transmit Skew = Transmit Package Skew + Spatial Skew + Logic Skew
Total Receive Skew
—
The total skew between data and strobe in receiving data from the bus into the PHY.
This is given by the following equation:
Total Receive Skew = Receive Package Skew + Spatial Skew + Receive Setup + Receive Hold
Skew Margin
—
The bit cell period minus all skews. This is given by the following equation:
Skew Margin = Bit Cell Period
–
Total Transmit Skew
–
Backplane Skew
–
Total Receive Skew
Transmit Edge Separation
—
The minimum time required between any two consecutive transitions of the
bus signals to ensure proper operation of data-strobe bit level encoding. Transmit edge separation is
measured from the midpoint of the signal transition to the midpoint of the next signal transition out on the
bus. Minimum transmit edge separation is the minimum bit cell period less the maximum total transmit skew.
Receive Edge Separation
—
The minimum time required between any two consecutive transitions of the bus
signals to ensure proper operation of data-strobe bit level decoding. Receive edge separation is measured
from the midpoint of the signal transition to the midpoint of the next signal transition out on the bus. This
is the minimum bit cell period reduced by the amount of maximum total transmit skew and maximum
backplane skew.
6.2.7
Gap Timing
A gap is a period of time during which the bus is idle (Data_Rx and Strb_Rx are unasserted). There are three types
of gaps:
Acknowledge Gap
—
Appears between the end of a packet and an acknowledge, as well as between
isochronous transfers. A node should detect the occurrence of an acknowledge gap after the bus has been
in an unasserted state for 4 arbitration clock times (approximately 81.38 ns) but should not assert the bus
until a total of 8 arbitration clock times (approximately 182.76 ns) have occurred. This requirement ensures
that a node is given adequate time to detect the acknowledge gap before the bus is asserted by another
node upon detecting an acknowledge gap. This includes the minimum time required to detect a Bus_Idle
(4 arbitration clock times), as well as the maximum delay between the arbitration state machine within any
two nodes on the bus (another 4 arbitration clock times).
Subaction Gap
—
Appears before asynchronous transfers within a fairness interval. A node should detect
the occurrence of a subaction gap after the bus has been in an unasserted state for at least 16 arbitration
clock times (approximately 325.52 ns), but should not assert the bus until a total of 20 arbitration clock times
(approximately 406.9 ns) have occurred. This requirement ensures that a node is given adequate time to
相关PDF资料 |
PDF描述 |
|---|---|
| TSB14AA1I | FPGA (Field-Programmable Gate Array) |
| TSB14AA1T | FPGA (Field-Programmable Gate Array) |
| TSB14C01MHV | IC APEX 20KE FPGA 160K 484-FBGA |
| TSB14C01HV | 5-V IEEE 1394-1995 BACKPLANE TRANSCEIVER/ARBITER |
| TSB21LV03MHV | IC APEX 20KE FPGA 200K 484-FBGA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TSB14AA1A | 制造商:TI 制造商全称:Texas Instruments 功能描述:3.3 V IEEE 1394-1995 BACKPLANE PHY |
| TSB14AA1AI | 制造商:TI 制造商全称:Texas Instruments 功能描述:3.3 V IEEE 1394-1995 BACKPLANE PHY |
| TSB14AA1AIPFB | 功能描述:1394 接口集成电路 IEEE139419953.3V1prt 50/100Mbps BkplnPHY RoHS:否 制造商:Texas Instruments 类型:Link Layer Controller 工作电源电压: 封装 / 箱体:LQFP 封装:Tray |
| TSB14AA1AIPFBG4 | 功能描述:1394 接口集成电路 3.3V 1-port 50/100 Mbps Backplane PHY RoHS:否 制造商:Texas Instruments 类型:Link Layer Controller 工作电源电压: 封装 / 箱体:LQFP 封装:Tray |
| TSB14AA1APFB | 功能描述:1394 接口集成电路 3.3V 1-port 50/100 Mbps Backplane PHY RoHS:否 制造商:Texas Instruments 类型:Link Layer Controller 工作电源电压: 封装 / 箱体:LQFP 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。