- 您现在的位置：买卖IC网 > PDF目录98302 > TSC2300IPAGRG4 (TEXAS INSTRUMENTS INC) SPECIALTY CONSUMER CIRCUIT, PQFP64 PDF资料下载
参数资料
| 型号： | TSC2300IPAGRG4 |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 消费家电 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PQFP64 |
| 封装： | GREEN, PLASTIC, TQFP-64 |
| 文件页数： | 10/83页 |
| 文件大小： | 1268K |
| 代理商： | TSC2300IPAGRG4 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页
www.ti.com
Z
2–Position
Touch
X+
X–
Y+
Y–
X-Position
Touch
Measure X-Position
Measure Z1-Position
X+
X–
Z-Position
Touch
Y+
Y–
X+
X–
Y+
Y–
Measure Z2-Position
TSC2300
SLAS372 — NOVEMBER 2002
Figure 46. Pressure Measurement
When the touch panel is pressed or touched, and the drivers to the panel are turned on, the voltage across the touch
panel often overshoots and then slowly settles (decay) down to a stable dc value. This is due to mechanical bouncing,
which is caused by vibration of the top layer sheet of the touch panel when the panel is pressed. This settling time
must be accounted for, or else the converted value is in error. Therefore, a delay must be introduced between the time
the driver for a particular measurement is turned on, and the time measurement is made.
In some applications, external capacitors may be required across the touch screen for filtering noise picked up by the
touch screen, i.e. noise generated by the LCD panel or back-light circuitry. The value of these capacitors provides a
low-pass filter to reduce the noise, but causes an additional settling time requirement when the panel is touched.
Several solutions to this problem are available in the TSC2300. A programmable delay time is available which sets the
delay between turning the drivers on and making a conversion. This is referred to as the panel voltage stabilization
time, and is used in some of the modes available in the TSC2300. In other modes, the TSC2300 can be commanded
to turn on the drivers only without performing a conversion. Time can then be allowed before the command is issued to
perform a conversion.
The TSC2300 touch screen interface can measure position (X,Y) and pressure (Z). Determination of these coordinates
is possible under three different modes of the A/D converter: conversion controlled by the TSC2300, initiated by
detection of a touch; conversion controlled by the TSC2300, initiated by the host responding to the PENIRQ signal; or
conversion completely controlled by the host processor.
A/D CONVERTER
The analog inputs of the TSC2300 are shown in Figure 47. The analog inputs (X, Y, and Z touch panel coordinates,
battery voltage monitors, chip temperature and auxiliary inputs) are provided via a multiplexer to the successive
approximation register (SAR) analog-to-digital (A/D) converter. The A/D architecture is based on capacitive
redistribution architecture which inherently includes a sample/hold function.
A unique configuration of low on-resistance switches allows an unselected ADC input channel to provide power and an
accompanying pin to provide ground for driving the touch panel. By maintaining a differential input to the converter and
a differential reference input architecture, it is possible to negate errors caused by the driver switch on-resistances.
The A/D is controlled by an A/D converter control register. Several modes of operation are possible, depending upon
the bits set in the control register. Channel selection, scan operation, averaging, resolution, and conversion rate may
all be programmed through this register. These modes are outlined in the sections below for each type of analog input.
The results of conversions made are stored in the appropriate result register.
18
相关PDF资料 |
PDF描述 |
|---|---|
| TSC2301IPAGR | SPECIALTY CONSUMER CIRCUIT, PQFP64 |
| TSC2301IPAG | SPECIALTY CONSUMER CIRCUIT, PQFP64 |
| TSC2301IGQZR | SPECIALTY CONSUMER CIRCUIT, PBGA120 |
| TSC2301IGQZ | SPECIALTY CONSUMER CIRCUIT, PBGA120 |
| TSC2301IZQZR | SPECIALTY CONSUMER CIRCUIT, PBGA120 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TSC2301 | 制造商:TI 制造商全称:Texas Instruments 功能描述:PROGRAMMABLE TOUCH SCREEN CONTROLLER WITH STEREO AUDIO CODEC |
| TSC2301EVM | 功能描述:触摸传感器开发工具 TSC2301 Eval Mod RoHS:否 制造商:Cypress Semiconductor 工具用于评估: 接口类型: 工作电压: 最大工作温度: |
| TSC2301IGQZ | 功能描述:触摸屏转换器和控制器 Prog 4-Wire w/20-Bit Stereo Audio Codec RoHS:否 制造商:Microchip Technology 类型:Resistive Touch Controllers 输入类型:3 Key 数据速率:140 SPS 分辨率:10 bit 接口类型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 电源电压:2.5 V to 5.25 V 电源电流:17 mA 工作温度:- 40 C to + 85 C 封装 / 箱体:SSOP-20 |
| TSC2301IGQZR | 功能描述:触摸屏转换器和控制器 Prog 4-Wire w/20-Bit Stereo Audio Codec RoHS:否 制造商:Microchip Technology 类型:Resistive Touch Controllers 输入类型:3 Key 数据速率:140 SPS 分辨率:10 bit 接口类型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 电源电压:2.5 V to 5.25 V 电源电流:17 mA 工作温度:- 40 C to + 85 C 封装 / 箱体:SSOP-20 |
| TSC2301IPAG | 功能描述:触摸屏转换器和控制器 Prog 4-Wire w/20-Bit Stereo Audio Codec RoHS:否 制造商:Microchip Technology 类型:Resistive Touch Controllers 输入类型:3 Key 数据速率:140 SPS 分辨率:10 bit 接口类型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 电源电压:2.5 V to 5.25 V 电源电流:17 mA 工作温度:- 40 C to + 85 C 封装 / 箱体:SSOP-20 |
发布紧急采购，3分钟左右您将得到回复。