- 您现在的位置：买卖IC网 > PDF目录98302 > TSC2301IZQZR (TEXAS INSTRUMENTS INC) SPECIALTY CONSUMER CIRCUIT, PBGA120 PDF资料下载
参数资料
| 型号： | TSC2301IZQZR |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 消费家电 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PBGA120 |
| 封装： | GREEN, PLASTIC, VFBGA-120 |
| 文件页数： | 14/95页 |
| 文件大小： | 1322K |
| 代理商： | TSC2301IZQZR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页
www.ti.com
TSC2301
SLAS371D – SEPTEMBER 2002 – REVISED AUGUST 2004
Reference
The TSC2301 has an internal voltage reference that can be set to 1.2 V or 2.5 V, through the reference control
register. This reference can also be set to automatically power down between conversions to save power, or
remain on to reduce settling time.
The internal reference voltage is only used in the single-ended mode for battery monitoring, temperature
measurement, and for utilizing the auxiliary inputs. Optimal touch screen performance is achieved when using a
ratiometric conversion, thus all touch screen measurements are done automatically in the differential mode.
An external reference can also be applied to the VREFIN pin, and the internal reference can be turned off.
Variable Resolution
The TSC2301 provides three different resolutions for the ADC: 8, 10, or 12 bits. Lower resolutions are often
practical for measurements such as touch pressure. Performing the conversions at lower resolution reduces the
amount of time it takes for the ADC to complete its conversion process, which lowers power consumption.
Conversion Clock and Conversion Time
The TSC2301 contains an internal 8-MHz clock, which is used to drive the state machines inside the device that
perform the many functions of the part. This clock is divided down to generate the actual ADC conversion clock.
The division ratio for this clock is set in the ADC control register. The ability to change the conversion clock rate
allows the user to choose the optimal value for resolution, speed, and power. If the 8-MHz clock is used directly,
the ADC is limited to 8-bit resolution; using higher resolutions at this speed does not result in accurate
conversions. Using a 4-MHz conversion clock is suitable for 10-bit resolution; 12-bit resolution requires that the
conversion clock run at 1 or 2 MHz.
Regardless of the conversion clock speed, the internal clock runs nominally at 8 MHz. The conversion time of the
TSC2301 is dependent upon several functions. While the conversion clock speed plays an important role in the
time it takes for a conversion to complete, a certain number of internal clock cycles is needed for proper
sampling of the signal. Moreover, additional times, such as the panel voltage stabilization time, can add
significantly to the time it takes to perform a conversion. Conversion time can vary depending upon the mode in
which the TSC2301 is used. Throughout this data sheet, internal and conversion clock cycles are used to
describe the times that many functions take. In considering the total system design, these times must be taken
into account by the user.
Touch Detect
The pen interrupt (PENIRQ) output function is detailed in Figure 49. While in the touch screen monitoring mode,
the Y- driver is ON and connected to GND, the X+ input is connected through a pullup resistor to VDD, and the
PENIRQ output reflects the state of the X+ input. When the panel is touched, the X+ input is pulled to ground
through the touch screen and PENIRQ output goes LOW due to the current path through the panel to GND,
initiating an interrupt to the processor. During the measurement cycles for X- and Y-position, the X+ input is
disconnected from PENIRQ to eliminate any leakage current from the pullup resistor that might flow through the
touch screen, thus causing no errors.
21
相关PDF资料 |
PDF描述 |
|---|---|
| TSC2301IZQZ | SPECIALTY CONSUMER CIRCUIT, PBGA120 |
| TSC2301IPAGG4 | SPECIALTY CONSUMER CIRCUIT, PQFP64 |
| TSC2301IPAGRG4 | SPECIALTY CONSUMER CIRCUIT, PQFP64 |
| TSC2302IRGZRG4 | SPECIALTY CONSUMER CIRCUIT, PQCC48 |
| TSDC4872IJT | 1 W, 1 CHANNEL, AUDIO AMPLIFIER, PBGA8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TSC2301PAG | 制造商:TI 制造商全称:Texas Instruments 功能描述:PROGRAMMABLE TOUCH SCREEN CONTROLLER WITH STEREO AUDIO CODEC |
| TSC2301PAGR | 制造商:TI 制造商全称:Texas Instruments 功能描述:PROGRAMMABLE TOUCH SCREEN CONTROLLER WITH STEREO AUDIO CODEC |
| TSC2302 | 制造商:BB 制造商全称:BB 功能描述:PROGRAMMABLE TOUCH SCREEN CONTROLLER WITH STEREO AUDIO CODEC |
| TSC2302IRGZ | 功能描述:触摸屏转换器和控制器 Prog 4-Wire w/20-Bit Stereo Audio Codec RoHS:否 制造商:Microchip Technology 类型:Resistive Touch Controllers 输入类型:3 Key 数据速率:140 SPS 分辨率:10 bit 接口类型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 电源电压:2.5 V to 5.25 V 电源电流:17 mA 工作温度:- 40 C to + 85 C 封装 / 箱体:SSOP-20 |
| TSC2302IRGZG4 | 功能描述:触摸屏转换器和控制器 Prog 4-Wire w/20-Bit Stereo Audio Codec RoHS:否 制造商:Microchip Technology 类型:Resistive Touch Controllers 输入类型:3 Key 数据速率:140 SPS 分辨率:10 bit 接口类型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 电源电压:2.5 V to 5.25 V 电源电流:17 mA 工作温度:- 40 C to + 85 C 封装 / 箱体:SSOP-20 |
发布紧急采购，3分钟左右您将得到回复。