- 您现在的位置：买卖IC网 > PDF目录16985 > TWR-ELEV (Freescale Semiconductor)TOWER ELEVATOR BOARDS HARDWARE PDF资料下载
参数资料
| 型号： | TWR-ELEV |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 4/48页 |
| 文件大小： | 0K |
| 描述： | TOWER ELEVATOR BOARDS HARDWARE |
| 其它有关文件： | TWR-ELEV Dummy Schematic TWR-ELEV Functional Schematic |
| 产品培训模块： | MCF51CN Family - Ultimate Ethernet Solutions Tower System |
| 特色产品： | The Tower System |
| 标准包装： | 1 |
| 系列： | ColdFire® |
| 附件类型： | 2 个升降机板 |
| 适用于相关产品： | Freescale 电源塔系统 |
| 产品目录页面： | 734 (CN2011-ZH PDF) |
| 相关产品： | TWR-SER-ND - TOWER SERIAL I/O HARDWARE TWR-MCF51CN-ND - KIT TOWER BOARD TWR-MCF51CN-KIT-ND - KIT TOWER BOARD/SERIAL/ELEVATOR |
第1页第2页第3页当前第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页
MCF51CN128 ColdFire Microcontroller Data Sheet, Rev. 4
Electrical Characteristics
Freescale Semiconductor
12
3.2
Parameter Classification
The electrical parameters shown in this supplement are guaranteed by various methods. To give the customer a better
understanding the following classification is used and the parameters are tagged accordingly in the tables where appropriate:
NOTE
The classification is shown in the column labeled “C” in the parameter tables where
appropriate.
3.3
Absolute Maximum Ratings
Absolute maximum ratings are stress ratings only, and functional operation at the maxima is not guaranteed. Stress beyond the
limits specified in Table 4 may affect device reliability or cause permanent damage to the device. For functional operating
conditions, refer to the remaining tables in this section.
This device contains circuitry protecting against damage due to high static voltage or electrical fields; however, it is advised
that normal precautions be taken to avoid application of any voltages higher than maximum-rated voltages to this
high-impedance circuit. Reliability of operation is enhanced if unused inputs are tied to an appropriate logic voltage level (for
instance, either VSS or VDD) or the programmable pull-up resistor associated with the pin is enabled.
Table 3. Parameter Classifications
P
These parameters are guaranteed during production testing on each individual device.
C
These parameters are achieved by the design characterization by measuring a statistically relevant sample
size across process variations.
T
These parameters are achieved by design characterization on a small sample size from typical devices
under typical conditions unless otherwise noted. All values shown in the typical column are within this
category.
D
These parameters are derived mainly from simulations.
Table 4. Absolute Maximum Ratings
Rating
Symbol
Value
Unit
Supply voltage
VDD
–0.3 to +3.8
V
Maximum current into VDD
IDD
120
mA
Digital input voltage
VIn
–0.3 to VDD +0.3
V
Instantaneous maximum current
Single pin limit (applies to all port pins)1, 2, 3
1
Input must be current limited to the value specified. To determine the value of the required
current-limiting resistor, calculate resistance values for positive (VDD) and negative (VSS) clamp
voltages, then use the larger of the two resistance values.
2 All functional non-supply pins are internally clamped to V
SS and VDD.
3 Power supply must maintain regulation within operating V
DD range during instantaneous and
operating maximum current conditions. If positive injection current (VIn > VDD) is greater than
IDD, the injection current may flow out of VDD and could result in external power supply going
out of regulation. Ensure external VDD load will shunt current greater than maximum injection
current. This will be the greatest risk when the MCU is not consuming power. Examples are: if
no system clock is present, or if the clock rate is very low (which would reduce overall power
consumption).
ID
± 25
mA
Storage temperature range
Tstg
–55 to 150
°C
相关PDF资料 |
PDF描述 |
|---|---|
| 2-1589449-6 | STRIP CON |
| 2-1589448-3 | STRIP CON |
| OPAMPEVM-SOIC | UNIV EVAL MOD FOR SOP PKG |
| 2-1589448-0 | STRIP CON |
| HFI-100505-2N2S | INDUCTOR 1.0X0.5X0.5MM 2.2NH |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TWR-ELEV | 制造商:Freescale Semiconductor 功能描述:Tower System - Elevator Boards |
| TWR-FRAM | 功能描述:存储器 IC 开发工具 Freescale Tower FRAM Daughter Card RoHS:否 制造商:STMicroelectronics 产品:Reference Boards 工具用于评估:M24LR64-R 存储容量:64 kbit 存储类型:EEPROM 工作电源电压:1.8 V to 5.5 V |
| TWR-HW | 功能描述:WIRELESS RELAY 120/277 HARD WIRE 制造商:thomas research products 系列:ZenNet 零件状态:过期 配件类型:无线继电器 配套使用产品/相关产品:* 标准包装:1 |
| TWR-IND-IO | 功能描述:界面开发工具 IND CTRL Tower IO RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| TWR-K20D50M | 功能描述:开发板和工具包 - ARM PK20DX128VLH5 EvBrd RoHS:否 制造商:Arduino 产品:Development Boards 工具用于评估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口类型:DAC, ICSP, JTAG, UART, USB 工作电源电压:3.3 V |
发布紧急采购，3分钟左右您将得到回复。