- 您现在的位置：买卖IC网 > PDF目录11806 > TXS02326RGER (Texas Instruments)IC SIM CARD MUX 2:1 24VQFN PDF资料下载
参数资料
| 型号： | TXS02326RGER |
| 厂商： | Texas Instruments |
| 文件页数： | 34/35页 |
| 文件大小： | 0K |
| 描述： | IC SIM CARD MUX 2:1 24VQFN |
| 产品培训模块： | Voltage Level Translation |
| 标准包装： | 1 |
| 应用： | 移动电话 |
| 接口： | I²C |
| 电源电压： | 1.7 V ~ 3.3 V |
| 封装/外壳： | 24-VFQFN 裸露焊盘 |
| 供应商设备封装： | 24-VQFN 裸露焊盘（4x4） |
| 包装： | 标准包装 |
| 安装类型： | 表面贴装 |
| 其它名称： | 296-27948-6 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页当前第34页第35页
SCES795C
– SEPTEMBER 2010 – REVISED FEBRUARY 2011
Table 10. Device Control Register (0Eh)(1)
Clock Control Register
Bits(s)
Type (R/W)
Description
‘0’ OE is not used to control the data
direction on the selected SIM I/O and the
OE Control
0
R/W
base band I/O
‘1’ OE controls the data direction, see below
‘0’ OE input = ‘0’ data direction Base band
-
> SIM
OE input =
‘1’ data direction SIM -> base
band
OE Direction Control
1
R/W
‘1’ OE input = ‘0’ data direction SIM -> base
band
OE input =
‘1’ data direction Base band ->
SIM
‘0’ Battery removal interrupt disabled
‘1’ Battery removal detected causes interrupt
Battery Removal Interrupt
2
R/W
on IRQ (interrupt sets b3 in the status
register)
BSI detection level
BSI Level Detection
3
R/W
‘0’ 1.2V
‘1’ 1.65V
BSI detection behavior
‘0’ Battery not present causes automatic
BSI Detection Control
4
R/W
power down of both SIM interfaces
‘1’ Battery not present doesn’t cause
automatic power down
‘0’ SDN detection interrupt disabled
SDN Detection Interrupt
5
R/W
‘1’ SDN detected causes interrupt on IRQ
(interrupt sets b1 in the status register)
SDN input active level
‘0’ SDN is active low
i.e. automatic shutdown occurs when
SDN Detection Level
6
R/W
debounced SDN is low.
‘1’ SDN is active high
i.e. automatic shutdown occurs when
debounced SDN is high
Disable automatic power down upon SDN
detection
‘0’ SDN detection causes automatic power
SDN Detection Control
7
R/W
down of SIM2 interface
‘1’ SDN detection doesn’t cause automatic
power down of SIM2 interface
(1)
Reset value: 00h
Table 11. General Purpose Register (15h)(1)
Function
Bit(s)
Type (R/W)
Description
'0' SDN input pull-up enabled
SDN pull-up control
0
R/W
'1' SDN input pull-up disabled
'0' SDN pull-down disabled
SDN pull-down control
1
R/W
'1' SDN pull-down enabled
RFU
7:2
R/W
(1)
The RFU bits shall allow for the write operation to complete but shall read as
'0'. The SW should write '0' into these locations, reset
value.
8
2010–2011, Texas Instruments Incorporated
Product Folder Link(s): TXS02326
相关PDF资料 |
PDF描述 |
|---|---|
| MS3114E12-8PW | CONN RCPT 8POS JAM NUT W/PINS |
| MS3114E12-8P | CONN RCPT 8POS JAM NUT W/PINS |
| MS3100A32-1P | CONN RCPT 5POS WALL MNT W/PINS |
| MS27497E12A4P | CONN RCPT 4POS WALL MNT W/PINS |
| D38999/20MB98PB | CONN RCPT 6POS WALL MNT W/PINS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TXS02612 | 制造商:TI 制造商全称:Texas Instruments 功能描述:SDIO PORT EXANDER WITH VOLTAGE-LEVEL TRANSLATION |
| TXS02612_10 | 制造商:TI 制造商全称:Texas Instruments 功能描述:SDIO PORT EXANDER WITH VOLTAGE-LEVEL TRANSLATION |
| TXS02612RTWR | 功能描述:转换 - 电压电平 SDIO Port Expander RoHS:否 制造商:Micrel 类型:CML/LVDS/LVPECL to LVCMOS/LVTTL 传播延迟时间:1.9 ns 电源电流:14 mA 电源电压-最大:3.6 V 电源电压-最小:3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:MLF-8 |
| TXS02612ZQSR | 功能描述:接口 - 专用 SDIO Port Expander RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
| TXS02AB00-04AI | 制造商:TE Connectivity 功能描述:TXS02AB00-04AI |
发布紧急采购，3分钟左右您将得到回复。