- 您现在的位置：买卖IC网 > PDF目录68428 > W25Q80BLSNIG (WINBOND ELECTRONICS CORP) 8M X 1 SPI BUS SERIAL EEPROM, PDSO8 PDF资料下载
参数资料
| 型号： | W25Q80BLSNIG |
| 厂商： | WINBOND ELECTRONICS CORP |
| 元件分类： | PROM |
| 英文描述： | 8M X 1 SPI BUS SERIAL EEPROM, PDSO8 |
| 封装： | 3.81 MM, GREEN, PLASTIC, SOIC-8 |
| 文件页数： | 32/75页 |
| 文件大小： | 2267K |
| 代理商： | W25Q80BLSNIG |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页当前第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页
W25Q80BL
- 38 -
9.2.19 Continuous Read Mode Bits (M7-0)
The “Continuous Read Mode” bits are used in conjunction with “Fast Read Dual I/O”, “Fast Read Quad
I/O”, “Word Read Quad I/O” and “Octal Word Read Quad I/O” instructions to provide the highest random
Flash memory access rate with minimum SPI instruction overhead, thus allow true XIP (execute in place)
to be performed on serial flash devices.
M7-0 need to be set by the Dual/Quad I/O Read instructions. M5-4 are used to control whether the 8-bit
SPI instruction code (BBh, EBh, E7h or E3h) is needed or not for the next command. When M5-4 = (1,0),
the next command will be treated same as the current Dual/Quad I/O Read command without needing
the 8-bit instruction code; when M5-4 do not equal to (1,0), the device returns to normal SPI mode, all
commands can be accepted. M7-6 and M3-0 are reserved bits for future use, either 0 or 1 values can be
used.
9.2.20 Continuous Read Mode Reset (FFh or FFFFh)
Continuous Read Mode Reset instruction can be used to set M4 = 1, thus the device will release the
Continuous Read Mode and return to normal SPI operation, as shown in figure 18.
/CS
Mode Bit Reset
for Dual I/O
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Mode 3
Mode 0
Mode Bit Reset
for Quad I/O
FFh
Don’t Care
IO
3
CLK
IO
0
IO
1
IO
2
/CS
Mode Bit Reset
for Dual I/O
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Mode 3
Mode 0
Mode Bit Reset
for Quad I/O
FFh
Don’t Care
IO
3
CLK
IO
0
IO
1
IO
2
Figure 18. Continuous Read Mode Reset for Fast Read Dual/Quad I/O
Since W25Q80BL does not have a hardware Reset pin, so if the controller resets while W25Q80BL is set
to Continuous Mode Read, the W25Q80BL will not recognize any initial standard SPI instructions from
the controller. To address this possibility, it is recommended to issue a Continuous Read Mode Reset
instruction as the first instruction after a system Reset. Doing so will release the device from the
Continuous Read Mode and allow Standard SPI instructions to be recognized.
To reset “Continuous Read Mode” during Quad I/O operation, only eight clocks are needed. The
instruction is “FFh”. To reset “Continuous Read Mode” during Dual I/O operation, sixteen clocks are
needed to shift in instruction “FFFFh”.
相关PDF资料 |
PDF描述 |
|---|---|
| W25Q80BVZPAG | 8M X 1 SPI BUS SERIAL EEPROM, PDSO8 |
| W25Q80BVSNIP | 8M X 1 SPI BUS SERIAL EEPROM, PDSO8 |
| W25X10AVDIAZ | 128K X 8 FLASH 2.7V PROM, PDIP8 |
| W25X16AVDAIG | 2M X 8 FLASH 2.7V PROM, PDIP8 |
| W25X16BVZPIG | 256K X 16 FLASH 2.7V PROM, PDSO8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| W25Q80BLSNIP | 制造商:WINBOND 制造商全称:Winbond 功能描述:2.5V 8M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI |
| W25Q80BLSSIG | 制造商:WINBOND 制造商全称:Winbond 功能描述:2.5V 8M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI |
| W25Q80BLSSIP | 制造商:WINBOND 制造商全称:Winbond 功能描述:2.5V 8M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI |
| W25Q80BLSVIG | 制造商:Winbond Electronics Corp 功能描述:8MB SERIAL FLASH MEMORY |
| W25Q80BLZPIG | 制造商:Winbond Electronics Corp 功能描述:FLASH |
发布紧急采购，3分钟左右您将得到回复。