- 您现在的位置：买卖IC网 > PDF目录140419 > W25X40BVSNIG (WINBOND ELECTRONICS CORP) 4M X 1 FLASH 2.7V PROM, PDSO8 PDF资料下载
参数资料
| 型号： | W25X40BVSNIG |
| 厂商： | WINBOND ELECTRONICS CORP |
| 元件分类： | PROM |
| 英文描述： | 4M X 1 FLASH 2.7V PROM, PDSO8 |
| 封装： | 0.150 INCH, GREEN, PLASTIC, SOIC-8 |
| 文件页数： | 17/51页 |
| 文件大小： | 1632K |
| 代理商： | W25X40BVSNIG |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页
W25X10BV/20BV/40BV
- 24 -
9.2.11
Continuous Read Mode Bits (M7-0)
The “Continuous Read Mode” bits are used in conjunction with the “Fast Read Dual I/O” instruction to
provide the highest random Flash memory access rate with minimum SPI instruction overhead, thus
allow true XIP (execute in place) to be performed on serial flash devices.
M7-0 need to be set by the Dual I/O Read instruction. M5-4 are used to control whether the 8-bit SPI
instruction code BBh is needed or not for the next command. When M5-4 = (1,0), the next command
will be treated same as the current Dual I/O Read command without needing the 8-bit instruction
code; when M5-4 do not equal to (1,0), the device returns to normal SPI mode, all commands can be
accepted. M7-6 and M3-0 are reserved bits for future use, either 0 or 1 values can be used.
9.2.12
Continuous Read Mode Reset (FFFFh)
Continuous Read Mode Reset instruction can be used to set M4 = 1, thus the device will release the
Continuous Read Mode and return to normal SPI operation, as shown in figure 12.
1
02
/CS
Mode 0
Mode 3
46
810
12
Mode 0
Mode 3
CLK
IO0
IO
Mode Bit Reset
for Dual I/O
Don’t Care
FFFFh
/CS
Mode 0
Mode 3
CLK
IO0
IO
Don’t Care
13
57
911
13
14
15
Figure 12. Continuous Read Mode Reset for Fast Read Dual I/O
Since W25X10BV/20BV/40BV does not have a hardware Reset pin, so if the controller resets while
W25X10BV/20BV/40BV are set to Continuous Mode Read, the W25X10BV/20BV/40BV will
not recognize any initial standard SPI instructions from the controller. To address this possibility, it is
recommended to issue a Continuous Read Mode Reset instruction as the first instruction after a
system Reset. Doing so will release the device from the Continuous Read Mode and allow Standard
SPI instructions to be recognized.
To reset “Continuous Read Mode” during Dual I/O operation, sixteen clocks are needed to shift in
instruction “FFFFh”.
相关PDF资料 |
PDF描述 |
|---|---|
| W3EG72126S202AJD3MF | 128M X 72 DDR DRAM MODULE, 0.75 ns, DMA184 |
| W3EG72126S335AJD3MG | 128M X 72 DDR DRAM MODULE, 0.7 ns, DMA184 |
| W3H128M72ER2-667SBM | 128M X 72 DDR DRAM, 0.5 ns, PBGA255 |
| W7NCF01GH10CS6BG | 64M X 16 FLASH 3.3V PROM CARD, 150 ns, UUC |
| W7NCF01GH10IS7AG | 64M X 16 FLASH 3.3V PROM CARD, 150 ns, UUC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| W25X40BVSSIG | 功能描述:IC SPI FLASH 4MBIT 8SOIC RoHS:是 类别:集成电路 (IC) >> 存储器 系列:SpiFlash® 标准包装:1,000 系列:- 格式 - 存储器:EEPROMs - 串行 存储器类型:EEPROM 存储容量:4K (512 x 8) 速度:400kHz 接口:I²C，2 线串口 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.173"，4.40mm 宽） 供应商设备封装:8-MFP 包装:带卷 (TR) |
| W25X40BVSSIG TR | 制造商:Winbond Electronics Corp 功能描述:SPIFLASH, 4M-BIT, 4KB UNIFORM 制造商:Winbond 功能描述:SPIFLASH, 4M-BIT, 4KB UNIFORM |
| W25X40BVZPIG | 功能描述:IC SPI FLASH 4MBIT 8WSON RoHS:是 类别:集成电路 (IC) >> 存储器 系列:SpiFlash® 标准包装:2,000 系列:- 格式 - 存储器:RAM 存储器类型:SRAM - 异步 存储容量:256K (32K x 8) 速度:15ns 接口:并联 电源电压:3 V ~ 3.6 V 工作温度:-40°C ~ 85°C 封装/外壳:28-TSSOP（0.465"，11.8mm 宽） 供应商设备封装:28-TSOP 包装:带卷 (TR) 其它名称:71V256SA15PZGI8 |
| W25X40CLDAIG | 制造商:Winbond Electronics Corp 功能描述:IC FLASH 4MBIT 104MHZ 制造商:Winbond Electronics Corp 功能描述:IC FLASH 4MBIT 104MHZ 8DIP |
| W25X40CLSNIG | 功能描述:IC FLASH SPI 4MBIT 8SOIC RoHS:是 类别:集成电路 (IC) >> 存储器 系列:SpiFlash® 标准包装:2,000 系列:- 格式 - 存储器:RAM 存储器类型:SRAM - 异步 存储容量:256K (32K x 8) 速度:15ns 接口:并联 电源电压:3 V ~ 3.6 V 工作温度:-40°C ~ 85°C 封装/外壳:28-TSSOP（0.465"，11.8mm 宽） 供应商设备封装:28-TSOP 包装:带卷 (TR) 其它名称:71V256SA15PZGI8 |
发布紧急采购，3分钟左右您将得到回复。