- 您现在的位置：买卖IC网 > PDF目录276884 > W29GL032CB7A (WINBOND ELECTRONICS CORP) 2M X 16 FLASH 3V PROM, 80 ns, PBGA48 PDF资料下载
参数资料
| 型号： | W29GL032CB7A |
| 厂商： | WINBOND ELECTRONICS CORP |
| 元件分类： | PROM |
| 英文描述： | 2M X 16 FLASH 3V PROM, 80 ns, PBGA48 |
| 封装： | GREEN, VFBGA-48 |
| 文件页数： | 7/65页 |
| 文件大小： | 650K |
| 代理商： | W29GL032CB7A |
第1页第2页第3页第4页第5页第6页当前第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页
W29GL032C
Publication Release Date: January 19, 2011
9
Preliminary - Revision B
7.2.9
Erasing the Memory Array
Sector Erase and Chip Erase are the two possible types of erase operations executed on the memory
array. Sector Erase operation erases one or more selected sectors and this can be simultaneous. Chip
Erase operation erases the entire memory array, except for any protected sectors.
7.2.9.1
Sector Erase
The sector erase operation returns all selected sectors in memory to the “1” state, effectively clearing
all data. This action requires six instruction cycles to commence the erase operation. The unlock
sequence is the first two cycles, followed by the configuration cycle, the fourth and fifth are
also ”unlock cycles”, and the Sector Erase instruction is the sixth cycle. An internal 50s time-out
counter is started once the sector erase instruction sequence has been completed. During this time,
additional sector addresses and Sector Erase commands may be issued, thus allowing for multiple
sectors to be selected and erased simultaneously. Once the 50s time-out counter has reached its
limit, no additional command instructions will be accepted and the embedded sector erase algorithm
will commence.
Note, that the 50s time-out counter restarts after every sector erase instruction sequence. The device
will abort and return to Read mode, if any instruction other than Sector Erase or Erase Suspend is
attempted during the time-out period.
Once the embedded sector erase algorithm begins, all instructions except Erase Suspend or
Hardware Reset will be ignored. The hardware reset will abort the erase operation and return the
device to the Read mode.
The embedded sector erase algorithm status can be verified by the following:
Status
DQ7
DQ6
DQ5
DQ3
1
DQ2
RY/#BY
2
Time-out period
0
Toggling
0
Toggling
0
In progress
0
Toggling
0
1
Toggling
0
Exceeded time limit
0
Toggling
1
Toggling
0
Table 7-4
Polling During Embedded Sector Erase Operation
Note:
1.
The DQ3 status bit is the 50s time-out indicator. When DQ3=0, the 50s time-out counter has not yet reached zero
and the new Sector Erase instruction maybe issued to specify the address of another sector to be erased. When
DQ3=1, the 50s time-out counter has expired and the Sector Erase operation has already begun. Erase Suspend is
the only valid instruction that maybe issued once the embedded erase operation is underway.
2.
RY/#BY is an open drain output pin and should be connected to VCC through a high value pull-up resistor.
3.
When an attempt is made to erase only protected sector(s), the erase operation will abort thus preventing any data
changes in the protected sector(s). DQ7 will output “0” and DQ6 will toggle briefly (100s or less) before aborting and
returning the device to Read mode. If unprotected sectors are also specified, however, they will be erased normally
and the protected sector(s) will remain unchanged.
4.
DQ2 is a localized indicator showing a specified sector is undergoing erase operation or not. DQ2 toggles when user
reads at the addresses where the sectors are actively being erased (in erase mode) or to be erased (in erase
suspend mode).
相关PDF资料 |
PDF描述 |
|---|---|
| W29GL032CB7S | 2M X 16 FLASH 3V PROM, 80 ns, PDSO48 |
| WV3HG2128M64EEU665D4SG | 256M X 64 DDR DRAM MODULE, 0.45 ns, ZMA200 |
| WF128K32-120HSC5A | 512K X 8 FLASH 5V PROM MODULE, 120 ns, CHIP66 |
| WF512K32-90G4I5 | 512K X 32 FLASH 5V PROM MODULE, 90 ns, CQFP68 |
| WPS512K8LB-70GI | 512K X 8 STANDARD SRAM, 70 ns, PDSO32 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| W29GL032CB7ATR | 制造商:Winbond Electronics Corp 功能描述:PF, 32M-BIT, 4KB UNIFORM SECTO |
| W29GL032CB7B | 制造商:Winbond Electronics Corp 功能描述:IC FLASH 32MBIT 70NS 64LFBGA |
| W29GL032CB7S | 功能描述:IC FLASH 32MBIT 70NS 48TSOP RoHS:是 类别:集成电路 (IC) >> 存储器 系列:- 标准包装:2,500 系列:- 格式 - 存储器:EEPROMs - 串行 存储器类型:EEPROM 存储容量:1K (128 x 8) 速度:100kHz 接口:UNI/O?（单线） 电源电压:1.8 V ~ 5.5 V 工作温度:-40°C ~ 85°C 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MSOP 包装:带卷 (TR) |
| W29GL032CH7B | 制造商:Winbond Electronics Corp 功能描述:IC FLASH 32MBIT 70NS 64LFBGA |
| W29GL032CH7T | 制造商:Winbond Electronics Corp 功能描述:IC FLASH 32MBIT 70NS 56TSOP |
发布紧急采购，3分钟左右您将得到回复。