- 您现在的位置：买卖IC网 > PDF目录68450 > W29GL032CT7B (WINBOND ELECTRONICS CORP) 2M X 16 FLASH 3V PROM, 80 ns, PBGA64 PDF资料下载
参数资料
| 型号： | W29GL032CT7B |
| 厂商： | WINBOND ELECTRONICS CORP |
| 元件分类： | PROM |
| 英文描述： | 2M X 16 FLASH 3V PROM, 80 ns, PBGA64 |
| 封装： | 11 X 13 MM, GREEN, FBGA-64 |
| 文件页数： | 8/65页 |
| 文件大小： | 650K |
| 代理商： | W29GL032CT7B |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页
W29GL032C
10
7.2.9.2
Chip Erase
The Chip Erase operation returns all memory locations containing a bit state of “0” to the “1” state,
effectively clearing all data. This action requires six instruction cycles to commence the erase
operation. The unlock sequence is the first two cycles, followed by the configuration cycle, the fourth
and fifth are also ”unlock cycles”, and the sixth cycle initiates the chip erase operation.
Once the chip erase algorithm begins, no other instruction will be accepted. However, if a hardware
reset is executed or the operating voltage is below acceptable levels, the chip erase operation will be
terminated and automatically returns to Read mode.
The embedded chip erase algorithm status can be verified by the following:
Status
DQ7
DQ6
DQ5
DQ2
RY/#BY
1
In progress
0
Toggling
0
Toggling
0
Exceeded time limit
0
Toggling
1
Toggling
0
Table 7-5
Polling During Embedded Chip Erase Operation
Note:
1.
RY/#BY is an open drain pin and should be connected to VCC through a high value pull-up resistor.
7.2.10
Erase Suspend/Resume
If there is a sector erase operation in progress, an Erase Suspend instruction is the only valid
instruction that may be issued. Once the Erase Suspend instruction is executed during the 50s time-
out period following a Sector Erase instruction, the time-out period will terminate right away and the
device will enter Erase-Suspend Read mode. If an Erase Suspend instruction is executed after the
sector erase operation has started, the device will not enter Erase-Suspended Read mode until
approximately 20s (5s typical) time has elapsed. To determine the device has entered the Erase-
Suspend Read mode, use DQ6, DQ7 and RY/#BY status to verify the state of the device.
Once the device has entered Erase-Suspended Read mode, it is possible to read or program any
sector(s) except those being erased by the erase operation. Only the contents of the status register is
present when attempting to read a sector that has been scheduled to erase or be programmed when
in the suspend mode. A resume instruction must be executed and recommend checking DQ6 toggle
bit status, before issuing another erase instruction.
The status register bits can be verified to determine the current status of the device:
Status
DQ7
DQ6
DQ5 DQ3 DQ2 DQ1RY/#BY
Erase suspend read in erase suspended sector
1
No toggle 0
N/A Toggle N/A
1
Erase suspend read in non-erase suspended sector
Data
DataData Data Data
1
Erase suspend program in non-erase suspended sector DQ7# Toggle
0
N/A
0
Table 7-6
Polling During Embedded Erase Suspend
Instruction sets such as read silicon ID, sector protect verify, program, CFI query and erase resume
can also be executed during Erase-Suspend mode, except sector and chip erase.
7.2.11 Sector Erase Resume
Only in the Erase-Suspended Read mode can the Sector Erase Resume instruction be a valid
command. Once erase resumes, another Erase Suspend instruction can be executed, but allow a
400s interval between Erase Resume and the next Erase Suspend instruction.
相关PDF资料 |
PDF描述 |
|---|---|
| W29GL064CL9B | 64M X 1 FLASH 3V PROM, 100 ns, PBGA64 |
| W29GL064CH9T | 64M X 1 FLASH 3V PROM, 100 ns, PDSO56 |
| W29L040T-25B | 512K X 8 FLASH 3.3V PROM, 250 ns, PDSO32 |
| W29L040-20B | 512K X 8 FLASH 3.3V PROM, 200 ns, PDIP32 |
| W3013BCL-TR | TELECOM, CELLULAR, RF AND BASEBAND CIRCUIT, PDSO20 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| W29GL032CT7S | 功能描述:IC FLASH 32MBIT 70NS 48TSOP RoHS:是 类别:集成电路 (IC) >> 存储器 系列:- 标准包装:2,500 系列:- 格式 - 存储器:EEPROMs - 串行 存储器类型:EEPROM 存储容量:1K (128 x 8) 速度:100kHz 接口:UNI/O?（单线） 电源电压:1.8 V ~ 5.5 V 工作温度:-40°C ~ 85°C 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MSOP 包装:带卷 (TR) |
| W29GL064C | 制造商:WINBOND 制造商全称:Winbond 功能描述:64M-BIT 3.0-VOLT PARALLEL FLASH MEMORY WITH PAGE MODE |
| W29GL064CB7A | 功能描述:IC FLASH 64MBIT 70NS 48TFBGA RoHS:是 类别:集成电路 (IC) >> 存储器 系列:- 标准包装:1 系列:- 格式 - 存储器:闪存 存储器类型:闪存 - NAND 存储容量:4G（256M x 16） 速度:- 接口:并联 电源电压:2.7 V ~ 3.6 V 工作温度:0°C ~ 70°C 封装/外壳:48-TFSOP（0.724"，18.40mm 宽） 供应商设备封装:48-TSOP I 包装:Digi-Reel® 其它名称:557-1461-6 |
| W29GL064CB7B | 制造商:Winbond Electronics Corp 功能描述:IC FLASH 64MBIT 70NS 64LFBGA |
| W29GL064CB7S | 功能描述:IC FLASH 64MBIT 70NS 48TSOP RoHS:是 类别:集成电路 (IC) >> 存储器 系列:- 标准包装:2,500 系列:- 格式 - 存储器:EEPROMs - 串行 存储器类型:EEPROM 存储容量:1K (128 x 8) 速度:100kHz 接口:UNI/O?（单线） 电源电压:1.8 V ~ 5.5 V 工作温度:-40°C ~ 85°C 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MSOP 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。