参数资料
| 型号： | X40021V14I-CT1 |
| 厂商： | Intersil |
| 文件页数： | 11/24页 |
| 文件大小： | 0K |
| 描述： | IC VOLTAGE MONITOR DUAL 14-TSSOP |
| 标准包装： | 2,500 |
| 类型： | 多压监控器 |
| 监视电压数目： | 2 |
| 输出： | 开路漏极或开路集电极 |
| 复位： | 低有效 |
| 复位超时： | 可调节/可选择 |
| 电压 - 阀值： | 1.6V，2.9V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 14-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 14-TSSOP |
| 包装： | 带卷 (TR) |
X40020, 40021
Figure 8. Valid Start and Stop Conditions
SCL
SDA
Start
Serial Acknowledge
Acknowledge is a software convention used to indi-
cate successful data transfer. The transmitting device,
either master or slave, will release the bus after trans-
mitting eight bits. During the ninth clock cycle, the
receiver will pull the SDA line LOW to acknowledge
that it received the eight bits of data. See Figure 9.
The device will respond with an acknowledge after
recognition of a start condition and if the correct
Device Identifier and Select bits are contained in the
Slave Address Byte. If a write operation is selected,
the device will respond with an acknowledge after the
receipt of each subsequent eight bit word. The device
will acknowledge all incoming data and address bytes,
except for the Slave Address Byte when the Device
Identifier and/or Select bits are incorrect.
In the read mode, the device will transmit eight bits of
data, release the SDA line, then monitor the line for an
acknowledge. If an acknowledge is detected and no
stop condition is generated by the master, the device
will continue to transmit data. The device will terminate
further data transmissions if an acknowledge is not
Figure 9. Acknowledge Response From Receiver
Stop
detected. The master must then issue a stop condition
to return the device to Standby mode and place the
device into a known state.
Serial Write Operations
Byte Write
For a write operation, the device requires the Slave
Address Byte and a Word Address Byte. This gives
the master access to any one of the words in the
array. After receipt of the Word Address Byte, the
device responds with an acknowledge, and awaits the
next eight bits of data. After receiving the 8 bits of the
Data Byte, the device again responds with an
acknowledge. The master then terminates the transfer
by generating a stop condition, at which time the
device begins the internal write cycle to the nonvolatile
memory. During this internal write cycle, the device
inputs are disabled, so the device will not respond to any
requests from the master. The SDA output is at high
impedance.
SCL from
Master
1
8
9
Data Output
from
Data Output
from Receiver
Start
11
Acknowledge
FN8112.1
May 17, 2006
相关PDF资料 |
PDF描述 |
|---|---|
| X40035V14I-CT1 | IC VOLTAGE MONITOR TRPL 14-TSSOP |
| X4005S8I-4.5A | IC SUPERVISOR CPU I2C 8-SOIC |
| X40239S16I-BT1 | IC VOLTAGE MON TRPL EE 16-SOIC |
| X40415V8I-CT1 | IC VOLTAGE MON DUAL W/SUP 8TSSOP |
| X40421V14I-CT1 | IC VOLT MON DUAL SUP/SW 14-TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| X400-22FA | 制造商:MOFLASH SIGNALLING 功能描述:BEACON XENON HIGH OUTPUT |
| X4003 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:CPU Supervisor |
| X4003_06 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:CPU Supervisor |
| X40030 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Triple Voltage Monitor with Intergrated CPU Supervisor |
| X40030_06 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Triple Voltage Monitor with Integrated CPU Supervisor |
发布紧急采购，3分钟左右您将得到回复。