参数资料
| 型号： | XC2S200E-6PQG208C |
| 厂商： | Xilinx Inc |
| 文件页数： | 23/108页 |
| 文件大小： | 0K |
| 描述： | IC SPARTAN-IIE FPGA 200K 208PQFP |
| 标准包装： | 24 |
| 系列： | Spartan®-IIE |
| LAB/CLB数： | 1176 |
| 逻辑元件/单元数： | 5292 |
| RAM 位总计： | 57344 |
| 输入/输出数： | 146 |
| 门数： | 200000 |
| 电源电压： | 1.71 V ~ 1.89 V |
| 安装类型： | 表面贴装 |
| 工作温度： | 0°C ~ 85°C |
| 封装/外壳： | 208-BFQFP |
| 供应商设备封装： | 208-PQFP（28x28） |
| 其它名称： | 122-1324 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页当前第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页
DS077-2 (v3.0) August 9, 2013
21
Product Specification
Spartan-IIE FPGA Family: Functional Description
R
— OBSOLETE — OBSOLETE — OBSOLETE — OBSOLETE —
design, thus allowing the most convenient entry method to
be used for each portion of the design.
Design Implementation
The place-and-route tools automatically provide the imple-
mentation flow described in this section. The partitioner
takes the EDIF netlist for the design and maps the logic into
the architectural resources of the FPGA (CLBs and IOBs,
for example). The placer then determines the best locations
for these blocks based on their interconnections and the
desired performance. Finally, the router interconnects the
blocks.
The algorithms support fully automatic implementation of
most designs. For demanding applications, however, the
user can exercise various degrees of control over the pro-
cess. User partitioning, placement, and routing information
is optionally specified during the design-entry process. The
implementation of highly structured designs can benefit
greatly from basic floorplanning.
The implementation software incorporates timing-driven
placement and routing. Designers specify timing require-
ments along entire paths during design entry. The timing
path analysis routines then recognize these user-specified
requirements and accommodate them.
Timing requirements are entered in a form directly relating
to the system requirements, such as the targeted clock fre-
quency, or the maximum allowable delay between two reg-
isters. In this way, the overall performance of the system
along entire signal paths is automatically tailored to
user-generated specifications. Specific timing information
for individual nets is unnecessary.
Design Verification
In addition to conventional software simulation, FPGA users
can use in-circuit debugging techniques. Because Xilinx
devices are infinitely reprogrammable, designs can be veri-
fied in real time without the need for extensive sets of soft-
ware simulation vectors.
The development system supports both software simulation
and in-circuit debugging techniques. For simulation, the
system extracts the post-layout timing information from the
design database, and back-annotates this information into
the netlist for use by the simulator. Alternatively, the user
can verify timing-critical portions of the design using the
static timing analyzer.
For in-circuit debugging, Xilinx offers a download cable,
which connects the FPGA in the target system to a PC or
workstation. After downloading the design into the FPGA,
the designer can read back the contents of the flip-flops,
and so observe the internal logic state. Simple modifica-
tions can be downloaded into the system in a matter of min-
utes.
Configuration
Configuration is the process by which the bitstream of a
design, as generated by the Xilinx development software, is
loaded into the internal configuration memory of the FPGA.
Spartan-IIE devices support both serial configuration, using
the master/slave serial and JTAG modes, as well as
byte-wide configuration employing the Slave Parallel mode.
Configuration File
Spartan-IIE devices are configured by sequentially loading
frames of data that have been concatenated into a configu-
ration file. Table 10 shows how much nonvolatile storage
space is needed for Spartan-IIE devices.
It is important to note that, while a PROM is commonly used
to store configuration data before loading them into the
FPGA, it is by no means required. Any of a number of differ-
ent kinds of under populated nonvolatile storage already
available either on or off the board (for example, hard drives,
FLASH cards, and so on) can be used.
Modes
Spartan-IIE devices support the following four configuration
modes:
Slave Serial mode
Master Serial mode
Slave Parallel mode
Boundary-scan mode
The Configuration mode pins (M2, M1, M0) select among
these configuration modes with the option in each case of
having the IOB pins either pulled up or left floating prior to
the end of configuration. The selection codes are listed in
Configuration through the boundary-scan port is always
available, independent of the mode selection. Selecting the
boundary-scan mode simply turns off the other modes. The
three mode pins have internal pull-up resistors, and default
to a logic High if left unconnected.
Table 10: Spartan-IIE Configuration File Size
Device
Configuration File Size (Bits)
XC2S50E
630,048
XC2S100E
863,840
XC2S150E
1,134,496
XC2S200E
1,442,016
XC2S300E
1,875,648
XC2S400E
2,693,440
XC2S600E
3,961,632
相关PDF资料 |
PDF描述 |
|---|---|
| XC2S200E-6PQ208C | IC FPGA 1.8V 1176 CLB'S 208-PQFP |
| 747275-4 | CONN D-SUB STRAIN RELIEF 9POS |
| XC3S700A-5FTG256C | IC FPGA SPARTAN-3A 256K 256FTBGA |
| XA3S400-4PQG208Q | IC FPGA SPARTAN-3 400K 208-PQFP |
| EEC43DTEF | CONN EDGECARD 86POS .100 EYELET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XC2S200E-6PQG208I | 制造商:XILINX 制造商全称:XILINX 功能描述:Spartan-IIE FPGA |
| XC2S200E-6TQ144C | 制造商:XILINX 制造商全称:XILINX 功能描述:Spartan-IIE 1.8V FPGA Family |
| XC2S200E-6TQ144I | 制造商:XILINX 制造商全称:XILINX 功能描述:Spartan-IIE 1.8V FPGA Family |
| XC2S200E-6TQG144C | 制造商:XILINX 制造商全称:XILINX 功能描述:Spartan-IIE FPGA |
| XC2S200E-6TQG144I | 制造商:XILINX 制造商全称:XILINX 功能描述:Spartan-IIE FPGA |
发布紧急采购，3分钟左右您将得到回复。