参数资料
| 型号： | XCF32PFS48C |
| 厂商： | Xilinx Inc |
| 文件页数： | 32/35页 |
| 文件大小： | 0K |
| 描述： | IC PROM SRL 1.8V 32M 48CSBGA |
| 标准包装： | 108 |
| 可编程类型： | 系统内可编程 |
| 存储容量： | 32Mb |
| 电源电压： | 1.65 V ~ 2 V |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 48-BFBGA，CSPBGA |
| 供应商设备封装： | 48-CSP（8x9） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页当前第32页第33页第34页第35页
Platform Flash In-System Programmable Configuration PROMs
DS123 (v2.18) May 19, 2010
Product Specification
6
R
Boundary-Scan Register
The Boundary-Scan register is used to control and observe
the state of the device pins during the EXTEST,
SAMPLE/PRELOAD, and CLAMP instructions. Each output
pin on the Platform Flash PROM has two register stages which
contribute to the Boundary-Scan register, while each input pin
has only one register stage. The bidirectional pins have a total
of three register stages which contribute to the Boundary-Scan
register. For each output pin, the register stage nearest to TDI
controls and observes the output state, and the second stage
closest to TDO controls and observes the High-Z enable state
of the output pin. For each input pin, a single register stage
controls and observes the input state of the pin. The
bidirectional pin combines the three bits, the input stage bit is
first, followed by the output stage bit and finally the output
enable stage bit. The output enable stage bit is closest to TDO.
See Table 12, page 24 and Table 13, page 26 for the
Boundary-Scan bit order for all connected device pins, or see
the appropriate BSDL file for the complete Boundary-Scan bit
order description under the “attribute
BOUNDARY_REGISTER” section in the BSDL file. The bit
assigned to Boundary-Scan cell 0 is the LSB in the Boundary-
Scan register, and is the register bit closest to TDO.
Identification Registers
IDCODE Register
The IDCODE is a fixed, vendor-assigned value that is used to
electrically identify the manufacturer and type of the device
being addressed. The IDCODE register is 32 bits wide. The
IDCODE register can be shifted out for examination by using
the IDCODE instruction. The IDCODE is available to any
other system component via JTAG. Table 8 lists the IDCODE
register values for the Platform Flash PROMs.
The IDCODE register has the following binary format:
vvvv:ffff:ffff:aaaa:aaaa:cccc:cccc:ccc1
where
v
= the die version number
f
= the PROM family code
a
= the specific Platform Flash PROM product ID
c
= the Xilinx manufacturer's ID
The LSB of the IDCODE register is always read as logic 1
as defined by IEEE Std. 1149.1.
USERCODE Register
The USERCODE instruction gives access to a 32-bit user
programmable scratch pad typically used to supply
information about the device's programmed contents. By
using the USERCODE instruction, a user-programmable
identification code can be shifted out for examination. This
code is loaded into the USERCODE register during
programming of the Platform Flash PROM. If the device is
blank or was not loaded during programming, the
USERCODE register contains FFFFFFFFh.
Customer Code Register
For the XCFxxP Platform Flash PROM, in addition to the
USERCODE, a unique 32-byte Customer Code can be
assigned to each design revision enabled for the PROM.
The Customer Code is set during programming, and is
typically used to supply information about the design
revision contents. A private JTAG instruction is required to
read the Customer Code. If the PROM is blank, or the
Customer Code for the selected design revision was not
loaded during programming, or if the particular design
revision is erased, the Customer Code contains all ones.
Table 6: XCFxxS Instruction Capture Values Loaded into IR as part of an Instruction Scan Sequence
TDI
→
IR[7:5]
IR[4]
IR[3]
IR[2]
IR[1:0]
→ TDO
Reserved
ISC Status
Security
0
0 1
Table 7: XCFxxP Instruction Capture Values Loaded into IR as part of an Instruction Scan Sequence
TDI
→
IR[15:9]
IR[8:7]
IR[6:5]
IR[4]
IR[3]
IR[2]
IR[1:0]
→ TDO
Reserved
ISC Error
ER/PROG
Error
ER/PROG
Status
ISC Status
DONE
0 1
Table 8: IDCODES Assigned to Platform Flash PROMs
Device
IDCODE(1) (hex)
XCF01S
<v>5044093
XCF02S
<v>5045093
XCF04S
<v>5046093
XCF08P
<v>5057093
XCF16P
<v>5058093
XCF32P
<v>5059093
Notes:
1.
The <v> in the IDCODE field represents the device’s revision
code (in hex) and can vary.
相关PDF资料 |
PDF描述 |
|---|---|
| XCR3256XL-7CS280C | IC CPLD 256MCELL 3.3V HP 280CSP |
| XCS10-3VQG100C | IC FPGA 5V C-TEMP 100-VQFP |
| XCV600E-8HQ240C | IC FPGA 1.8V C-TEMP 240-HQFP |
| XCV812E-8FG900C | IC FPGA 1.8V C-TEMP 900-FBGA |
| XE8801AMI000WP | SENSING MACHINE WITH 16 + 10 BIT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XCF32PFS48C0936 | 制造商:Xilinx 功能描述:XLXXCF32PFS48C0936 |
| XCF32PFS48CES | 制造商:Xilinx 功能描述: |
| XCF32PFS48CESB | 制造商:Xilinx 功能描述: |
| XCF32PFSG48C | 功能描述:IC PROM SRL 1.8V 32M 48CSBGA RoHS:是 类别:集成电路 (IC) >> 存储器 - 用于 FPGA 的配置 Proms 系列:- 产品变化通告:Product Discontinuation 28/Jul/2010 标准包装:98 系列:- 可编程类型:OTP 存储容量:300kb 电源电压:3 V ~ 3.6 V 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-TSOP 包装:管件 |
| XCF32PFSG48C4039 | 制造商:Xilinx 功能描述: |
发布紧急采购，3分钟左右您将得到回复。