参数资料
型号: XRT73LC00AIV-F
厂商: Exar Corporation
文件页数: 39/61页
文件大小: 0K
描述: IC LIU STS1/DS3/E3 SGL 44TQFP
标准包装: 160
类型: 线路接口装置(LIU)
驱动器/接收器数: 1/1
规程: DS3,E3,STS-1
电源电压: 3.135 V ~ 3.465 V
安装类型: 表面贴装
封装/外壳: 44-LQFP
供应商设备封装: 44-TQFP(10x10)
包装: 托盘
XRT73LC00A
41
E3/DS3/STS-1 LINE INTERFACE UNIT
REV. 1.0.2
It is useful to disable the DLOS Detector in the XRT73LC00A for debugging purposes. If the XRT73LC00A is
operating in the HOST Mode, the DLOS Detector can be disabled by writing a “1” into the DLOSDIS bit-field in
Command Register 2.
NOTE: Setting both the ALOSDIS and DLOSDIS bit-fields to a “1” disables LOS Declaration in the XRT73LC00A.
3.6.3
Muting the Recovered Data while the LOS is being Declared
In some applications it is not desirable for the XRT73LC00A E3/DS3/STS-1 LIU to recover data and route it to
the Receiving Terminal while the LIU is declaring a LOS condition. The LOS Muting feature, if enabled, causes
the XRT73LC00A to halt transmission of the recovered data to the Receiving Terminal while the LOS condition
is True. In this case, the RPOS and RNEG output pins are forced to “0”. Once the LOS condition has been
cleared, the XRT73LC00A resumes the transmission of the recovered data to the Receiving Terminal. The
XRT73LC00A allows enabling of the Muting Upon LOS feature by either of the following means.
If the XRT73LC00A is Operating in the Hardware Mode:
The Muting Upon LOS feature is enabled by pulling the LOSMUTEN input pin (pin 19) to VDD.
If the XRT73LC00A is Operating in the HOST Mode:
To enable this feature, access the Microprocessor Serial Interface and write a “1” into the LOSMUT bit-field in
Command Register 3.
NOTE: The XRT73LC00A automatically declares an LOS Condition any time it has been configured to operate in either the
Analog Local Loop-Back or Digital Local Loop-Back Modes.
Muting -upon -LOS must be disabled
prior to
configuring the device to operate in either of these local Loop-Back modes.
3.7
Routing the Recovered Timing and Data Information to the Receiving Terminal Equipment
The XRT73LC00A ultimately takes the Recovered Timing and Data information, converts it into CMOS levels
and routes it to the Receiving Terminal Equipment via the RPOS, RNEG, RCLK1 and RCLK2 output pins.
The XRT73LC00A can deliver the recovered data and clock information to the Receiving Terminal in either a
Single-Rail or Dual-Rail format.
Routing Dual-Rail Format Data to the Receiving Terminal Equipment
Whenever the XRT73LC00A delivers Dual-Rail format to the Terminal Equipment it does so via the following
output signals.
n
RPOS
n
RNEG
n
RCLK1
n
RCLK2
Figure 24 illustrates the typical interface for the transmission of data in a Dual-Rail Format from the Receive
Section of the XRT73LC00A to the Receiving Terminal Equipment.
COMMAND REGISTER CR2 (ADDRESS = 0X02)
D4
D3
D2
D1
D0
Reserved ENDECDIS ALOSDIS DLOSDIS REQDIS
X
1
X
COMMAND REGISTER CR3 (ADDRESS = 0X03)
D4
D3
D2
D1
D0
RNRZ
LOSMUT
CLK2DIS RCLK2INV CLK1INV
X
1
X
相关PDF资料
PDF描述
XRT73LC03AIV-F IC LIU E3/DS3/STS-1 3CH 120LQFP
XRT73LC04AIV-F IC LIU E3/DS3/STS-1 4CH 144LQFP
XRT73R06IB-F IC LIU E3/DS3/STS-1 6CH 217BGA
XRT73R12IB-L IC LIU E3/DS3/STS-1 12CH 420TBGA
XRT75L00DIV-F IC LIU E3/DS3/STS-1 SGL 52TQFP
相关代理商/技术参数
参数描述
XRT73LC00AIVTR 功能描述:网络控制器与处理器 IC RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流(最大值):595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray
XRT73LC00AIVTR-F 功能描述:网络控制器与处理器 IC RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流(最大值):595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray
XRT73LC00IV 制造商:EXAR 制造商全称:EXAR 功能描述:E3/DS3/STS-1 LINE INTERFACE UNIT
XRT73LC03A 制造商:EXAR 制造商全称:EXAR 功能描述:3 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT
XRT73LC03A_08 制造商:EXAR 制造商全称:EXAR 功能描述:3 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT