参数资料
| 型号： | XRT82L24AIV-F |
| 厂商： | Exar Corporation |
| 文件页数： | 20/39页 |
| 文件大小： | 0K |
| 描述： | IC LIU E1 QAUD 100TQFP |
| 标准包装： | 90 |
| 类型： | 线路接口装置（LIU） |
| 驱动器/接收器数： | 4/4 |
| 规程： | E1 |
| 电源电压： | 3.135 V ~ 3.465 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 100-LQFP |
| 供应商设备封装： | 100-TQFP（14x14） |
| 包装： | 托盘 |
| 其它名称： | XRT82L24AIV-F-ND |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页当前第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页
á
XRT82L24A
QUAD E1 LINE TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR
REV. 1.1.2
25
TABLE 10: COMMAND CONTROL REGISTER 0
COMMAND CONTROL REGISTER 0
PARALLEL PORT ADDRESS: 0000
BIT NO.NAME
FUNCTION
REGISTER
TYPE
RESET
VALUE
7
SR/DR
Single/Dual Rail:
Writing a "1" to this bit selects transmit and receive data format in
single-rail mode. In this mode, HDB3/B8ZS/AMI encoder and
decoder are available.
Writing a "0" selects dual-rail mode.
R/W
0
6RZData
RZ Data:
Writing a “1” to this bit selects receive data to pass to the output
after the slicers without re-timing. In this mode, PLL clock recov-
ery, jitter attenuator, decoder and remote loop-back functions are
disabled.
R/W
0
5RCLKE
RxClk Clock Edge:
Writing a "1" to this bit selects receive output data to be updated
on positive edge of RxClk.
Writing a "0" to this bit selects the negative edge of RxClk.
R/W
0
4TCLKE
TxClk Clock Edge:
Writing a "1" to this bit selects positive edge of TxClk to sample
input data.
Write "0" to select negative edge.
R/W
0
3DATAP
DATA Polarity:
Writing a "0" to this bit selects transmit input and receive output
data to be active-high.
Write "1" to select active-low.
R/W
0
2CODES
Coding/Decoding Select:
This bit is used in conjunction with SR/DR bit 1. If SR/DR is "1",
writing a "0" to this bit selects HDB3 coding. Writing a "1" to this
bit position selects AMI code.
R/W
0
1GIE
Global Interrupt Enable:
Writing a "0" to this bit globally disables interrupt generation
caused by any alarm generated within the line interface. Write a
"1" to enable interrupt generation.
R/W
0
SRESET
Software Reset:
Writing a "1" to this bit longer than 10s initiates a device reset
through the microprocessor interface. All internal circuits are
placed in the reset state with this bit set to a "1" except the micro-
processor register bits.
R/W
0
NOTE: Register Type Abrbreviation:
R = Read Only, R/W = Read or Write, RUR = Reset Upon Read
相关PDF资料 |
PDF描述 |
|---|---|
| XRT83D10IW | IC LIU T1/E1 SGL 28SOJ |
| XRT83L30IV-F | IC LIU LH/SH T1/E1 SGL 64TQFP |
| XRT83L314IB-L | IC LIU T1/E1/J1 14CH 304TBGA |
| XRT83L34IV-F | IC LIU T1/E1/J1 QUAD 128TQFP |
| XRT83L38IB-F | IC LIU T1/E1/J1 OCTAL 225BGA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XRT82L24ES | 功能描述:界面开发工具 Evaluation Board for XRT82L24 Series RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| XRT82L24IV | 制造商:EXAR 制造商全称:EXAR 功能描述:QUAD E1 LINE TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR |
| XRT82L34IV | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Interface IC |
| XRT83D10 | 制造商:EXAR 制造商全称:EXAR 功能描述:SINGLE CHANNEL DS1/CEPT LINE INTERFACE UNIT |
| XRT83D10ES | 功能描述:外围驱动器与原件 - PCI 1 CHT1/E1LIUSH RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。