参数资料
| 型号： | XRT83SL30IV-F |
| 厂商： | Exar Corporation |
| 文件页数： | 48/76页 |
| 文件大小： | 0K |
| 描述： | IC LIU T1/E1/J1 SGL 64TQFP |
| 标准包装： | 160 |
| 类型： | 线路接口装置（LIU） |
| 驱动器/接收器数： | 1/1 |
| 规程： | T1，E1，J1 |
| 电源电压： | 3.135 V ~ 3.465 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 64-LQFP |
| 供应商设备封装： | 64-TQFP（10x10） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页当前第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页
XRT83SL30
49
SINGLE-CHANNEL T1/E1/J1 SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR
REV. 1.0.1
TABLE 21: MICROPROCESSOR REGISTER #3 BIT DESCRIPTION
REGISTER ADDRESS
00011
FUNCTION
REGISTER
TYPE
RESET
VALUE
BIT #
NAME
D7
NLCDE1
Network Loop Code Detection Enable bit 1:
This bit together with NLCDE0, Control the Loop-Code detection
according to the following table:
When NLCDE1=”0” and NCLDE0=”1”, or NLCDE1=”1” and
NLCDE0=”0”, the chip is manually programed to monitor the
receive data for the Loop-Up or Loop-Down code respectively.
When the presence of the “00001” or “001” pattern is detected for
more than 5 seconds, the status of the NLCD bit is set to “1” and
if the NLCD interrupt is enabled an interrupt is initiated. The Host
has the option to control the Loop-Back function manually.
Setting the NLCDE1=”1” and NLCDE0=”1” enables the Auto-
matic Loop-Code detection and Remote-Loop-Back activation
mode. As this mode is initiated, the state of the NLCD interface
bit is reset to “0” and the chip is programmed to monitor the
receive data for the Loop-Up Code. If the “00001” pattern is
detected for longer than 5 seconds, the NLCD bit is set to “1”,
Remote Loop-Back is activated and the chip is automatically pro-
gramed to monitor the receive data for the Loop-Down code. The
NLCD bit stays set even after the chip stops receiving the Loop-
Up code. The remote Loop-Back condition is removed when the
chip receives the Loop-Down code for more than 5 seconds or if
the Automatic Loop-Code detection mode is terminated.
R/W
0
D6
NLCDE0
Network Loop Code Detection Enable bit 0:
See description
of bit D7 for the function of this bit.
R/W
0
D5
CODES
ENCODING and DECODING SELECT:
Writing a “0” to this bit selects HDB3 or B8ZS encoding and
decoding. Writing a “1” selects an AMI coding scheme.This bit is
only active when single-rail mode is selected.
R/W
0
NLCDE1
NLCDE0
Function
0
Disable Loop-Code
Detection
0
1
Detect Loop-Up Code in
Receive Data
1
Automatic Loop-Code
Detection
1
0
Detect Loop-Down Code in
Receive Data
相关PDF资料 |
PDF描述 |
|---|---|
| XRT83SL314IB-L | IC LIU SH T1/E1/J1 14CH 304TBGA |
| XRT83SL34IV-F | IC LIU T1/E1/J1 QUAD 128TQFP |
| XRT83SL38IB-F | IC LIU SH T1/E1/J1 OCTAL 225BGA |
| XRT83VL38IB-F | IC LIU SH T1/E1/J1 OCTAL 225BGA |
| XRT83VSH28IB | IC LIU SH E1 OCTAL 225BGA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XRT83SL30IVTR-F | 功能描述:外围驱动器与原件 - PCI RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
| XRT83SL314 | 制造商:EXAR 制造商全称:EXAR 功能描述:14-CHANNEL T1/E1/J1 SHORT-HAUL LINE INTERFACE UNIT |
| XRT83SL314_05 | 制造商:EXAR 制造商全称:EXAR 功能描述:14-CHANNEL T1/E1/J1 SHORT-HAUL LINE INTERFACE UNIT |
| XRT83SL314ES | 功能描述:LIN 收发器 14 CHT1/E1 LIUSH RoHS:否 制造商:NXP Semiconductors 工作电源电压: 电源电流: 最大工作温度: 封装 / 箱体:SO-8 |
| XRT83SL314IB | 功能描述:外围驱动器与原件 - PCI RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。