- 您现在的位置：买卖IC网 > Datasheet目录581 > 0639003700 (Molex Inc)TOOL CRIMPER 28-32AWG 1.25MM Datasheet资料下载
参数资料
| 型号： | 0639003700 |
| 厂商： | Molex Inc |
| 文件页数： | 11/50页 |
| 文件大小： | 0K |
| 描述： | TOOL CRIMPER 28-32AWG 1.25MM |
| RoHS指令信息： | 0639003700 Cert of Compliance |
| 标准包装： | 1 |
| 系列： | FineAdjust™, PicoBlade™ |
| 工具类型： | 台式压机，施用器 |
| 适用于相关产品： | 刀片型触点，26-32 AWG |
| 配用： | 0500588300-ND - 1.25 W/B TERMINAL(NEW) WM1775TR-ND - CONN TERM FEMALE 28-32AWG TIN WM1142CT-ND - CONN TERM FEMALE 26-28AWG TIN WM1142TR-ND - CONN TERM FEMALE 26-28AWG TIN WM1775CT-ND - CONN TERM FEMALE 28-32AWG TIN |
| 相关产品： | WM3459-ND - TM3000 220V/50HZ PRESS TO 10AWG WM6378-ND - PRESS TM4000 UP TO 4AWG 240AC WM4793-ND - CRMP PRESS TM3000 120V TO 10AWG |
| 其它名称： | 63900-3700 639003700 WM4245 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页
FineAdjust Applicator
Read the following instructions before attempting to operate the applicators.
2.1 Shut Height
The Molex FineAdjust Applicators are designed to operate in crimp
presses with standard shut height of 135.80mm (5.346").
Installation in crimp presses with other than standard shut heights
can cause severe tool breakage. It is recommended that before
installation, a check of the shut height be performed. The correct
shut height is required to prevent the punches from hitting the anvils
and the cut-off tooling from bottoming out on the base plate. It also
allows the movement of applicators from press to similar press
without adjusting the applicator or press shut height.
The shut height of the press can be checked with a shut height
gauge, which is calibrated under load to achieve the 135.80mm
(5.346") measurement. It is recommended that the shut height be
checked monthly. A shut height gauge is available from most press
manufacturers.
SHUT HEIGHT
GAUGE
PRESS QUICK
CHANGE
MOUNTING PLATE
PRESS
Figure 2-1
Measuring Press Shut Height
1. Always disconnect the power supply from the press. Remove the machine guards if necessary.
2. Remove the applicator from the press. See “Applicator Installation and Removal” (below) for additional information. Make
sure that the bottom of the press ram and quick change mounting plate are free from foreign material.
3.
4.
5.
6.
7.
8.
Place the shut height gauge into the press on the press quick change mounting plate. See Figure 2-1.
Manually cycle the press to the down stroke position. (Follow press manufacturer’s instructions on manually cycling the
press.)
Read the shut height measurement from the front of the gauge. Follow gauge manufacturers’ instruction, usually the gauge
reads “0” when set correctly.
If adjustments are necessary, refer to the press manufacturer for adjustment of the press shut height.
Repeat the above steps until the correct shut height is obtained.
Shut height gauges must be calibrated on a regular basis.
2.2 Set-Up
IMPORTANT
Power must be shut off and electrical cord disconnected. Manual press cycling is an absolutely required procedure
for safety and preventing equipment damage. Always cycle by hand when trouble shooting or changing adjustments,
tooling, applicator, or accessories.
The principal mechanical parts of the FineAdjust are illustrated in Section 4.1 Assembly Drawings.
Applicator Installation and Removal
1
2
3
4
All presses must be equipped with a common universal type quick-change mounting plate and adapter on the press.
Contact the press manufacturer for specific information.
Always turn off and disconnect the power supply to the press. Remove the press guards.
Clean the quick change mounting plate of scrap or chips that may interfere with the FineAdjust applicator installation.
For the TM-2000 and TM-3000 Presses follow the procedure below:
a. Using a 4mm hex wrench, turn the M5 SHCS clockwise until the locking clamp is fully opened.
b. Visually align the applicator base plate slots with the location clamps on the press quick-change mounting plate.
Doc. No: TM-638004900
Revision: G
Release Date: 09-04-03
Revision Date: 01-15-13
UNCONTROLLED COPY
Page 11 of 50
相关PDF资料 |
PDF描述 |
|---|---|
| 0639003770 | TOOL KIT |
| 0639003870 | TOOL KIT |
| 0639003970 | TOOL KIT |
| 0639004070 | TOOL KIT |
| 0639004270 | TOOL KIT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 0639003770 | 功能描述:TOOL KIT RoHS:是 类别:工具 >> 压接器，施用器，压力机 - 配件 系列:* 标准包装:1 系列:- 其它名称:512A512A-NDQ1137690B |
| 0639003800 | 功能描述:FINE ADJUST APPLICATOR RoHS:是 类别:工具 >> 压接器，施用器，压力机 系列:FineAdjust™, MicroBlade™ 产品培训模块:Board-to-Wire Connectors 标准包装:1 系列:DF11 工具类型:台式压机，施用器 适用于相关产品:矩形触点，24-28 AWG 特点:- 配用:H1505TR-ND - CONN SOCKET 24-28AWG CRIMP GOLDH1504TR-ND - CONN SOCKET 24-28AWG CRIMP TIN 相关产品:AP105-DF11-2428S(64)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(63)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(62)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(61)-ND - TOOL APPLICATOR DF11 ACCESSORIESCM-105 WITH TRANSFORMER-ND - TOOL AUTO CRIMPING MACHINE 其它名称:*AP105-DF11-2428SQ1139807AQ949366 |
| 0639003870 | 功能描述:TOOL KIT RoHS:是 类别:工具 >> 压接器，施用器，压力机 - 配件 系列:* 标准包装:1 系列:- 其它名称:512A512A-NDQ1137690B |
| 0639003900 | 功能描述:FINE ADJUST APPLICATOR RoHS:是 类别:工具 >> 压接器，施用器，压力机 系列:FineAdjust™, MicroBlade™ 产品培训模块:Board-to-Wire Connectors 标准包装:1 系列:DF11 工具类型:台式压机，施用器 适用于相关产品:矩形触点，24-28 AWG 特点:- 配用:H1505TR-ND - CONN SOCKET 24-28AWG CRIMP GOLDH1504TR-ND - CONN SOCKET 24-28AWG CRIMP TIN 相关产品:AP105-DF11-2428S(64)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(63)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(62)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(61)-ND - TOOL APPLICATOR DF11 ACCESSORIESCM-105 WITH TRANSFORMER-ND - TOOL AUTO CRIMPING MACHINE 其它名称:*AP105-DF11-2428SQ1139807AQ949366 |
| 0639003970 | 功能描述:TOOL KIT RoHS:是 类别:工具 >> 压接器，施用器，压力机 - 配件 系列:* 标准包装:1 系列:- 其它名称:512A512A-NDQ1137690B |
发布紧急采购，3分钟左右您将得到回复。