收藏本站
参数资料
型号： 0639003700
厂商： Molex Inc
文件页数： 15/50页
文件大小： 0K
描述： TOOL CRIMPER 28-32AWG 1.25MM
RoHS指令信息： 0639003700 Cert of Compliance
标准包装： 1
系列： FineAdjust™, PicoBlade™
工具类型： 台式压机，施用器
适用于相关产品： 刀片型触点，26-32 AWG
配用： 0500588300-ND - 1.25 W/B TERMINAL(NEW)
WM1775TR-ND - CONN TERM FEMALE 28-32AWG TIN
WM1142CT-ND - CONN TERM FEMALE 26-28AWG TIN
WM1142TR-ND - CONN TERM FEMALE 26-28AWG TIN
WM1775CT-ND - CONN TERM FEMALE 28-32AWG TIN
相关产品： WM3459-ND - TM3000 220V/50HZ PRESS TO 10AWG
WM6378-ND - PRESS TM4000 UP TO 4AWG 240AC
WM4793-ND - CRMP PRESS TM3000 120V TO 10AWG
其它名称： 63900-3700
639003700
WM4245
FineAdjust Applicator
Forward Feed Adjustments
1. The forward feed position must locate the terminal that is
being crimped exactly over the anvils.
2. Disconnect the power from the press. Remove the
M5 SHCS
FEED LOCK
machine guards if necessary.
3. Make sure there is a terminal over the anvils and the feed
finger is fully forward (closest to the anvils).
4. Loosen the M5 SHCS.
5. Turn the forward feed adjusting knob to position the
terminal. To decrease the feed position, turn the forward
feed adjusting knob clockwise. To increase the feed
position turn the forward feed adjusting knob
counterclockwise. See Figure 2-10.
6. When adjusting to decrease the feed position, it is
FORWARD
FEED
STROKE
ADJ. KNOB
Figure 2-10
BACK
STROKE
ADJ. KNOB
PIVOT CLAMP
M5 FHCS
necessary to pull the terminal strip backwards until it is against the feed finger. When increasing the feed position, the feed
finger will push the terminal farther over the anvils.
7. After properly adjusting the forward feed position of the terminal, tighten the M5 SHCS with a 4mm hex wrench.
Back Stroke Feed Adjustments
INSULATION
CAM (TOP)
1. To properly feed the terminal strip, the back feed stroke should have
enough over-travel to pick up the next terminal. Too much over
travel may, in some cases, cause a double-feed.
2. Disconnect the power from the press. Remove the machine guards if
necessary.
3. To achieve the correct backstroke location, adjust the position of the
hinge bushing. First, use a 3mm hex wrench to loosen the M5 FHCS
holding the pivot clamp. Turning the backstroke adjustment knob
(which is located above the hinge bushing) clockwise will raise the
hinge bushing and will increase the backstroke. Turning the knob
counter clockwise (CCW) will lower the hinge bushing and will
Figure 2-11
CONDUCTOR
CAM (BOTTOM)
decrease the feed backstroke. When adjustment is complete, tighten
the pivot clamp securely. See Figure 2-10.
4. Since back feed stroke adjustment may not be visibly obvious, the terminal feed should be cycled (by hand, if possible) to
observe the changes.
5. Back feed stroke adjustments may affect the entire feed linkage; re-adjustment of the forward feed stroke could be
necessary. See Forward Feed Adjustments.
Conductor Crimp Punch Adjustments
1. With the guards intact, place a stripped length of suitable wire into the terminal and terminate the wire under power.
2. Inspect the quality of conductor crimp and measure the crimp height. See Appendix A.3 Conductor Crimp Height
Measurement.
3.
4.
5.
6.
If adjustments are necessary, turn off and disconnect the power supply from the press. Remove the machine guards.
The desired crimp height can be achieved by rotating the conductor-adjusting cam. See Figure 2-11. Each increment
represents approximately 0.015mm (.0006") for a total adjustment of 1.80mm (.071"). The "A" setting is the loosest crimp
height and the "N" setting is the tightest. If you find that the crimp height is not acceptable, you can rotate the adjusting cam
until the desired crimp height is obtained. See Section 2.1, Shut Height. No shimming of the applicator is required.
Replace the machine guards and repeat the previous steps until the desired crimp height is obtained. See Appendix A.3,
Conductor Crimp Height Measurement.
Perform a pull test on conductor crimp to verify the mechanical integrity of the crimp. See Appendix A.5, Pull Force Test.
Doc. No: TM-638004900
Revision: G
Release Date: 09-04-03
Revision Date: 01-15-13
UNCONTROLLED COPY
Page 15 of 50
相关PDF资料
PDF描述
0639003770 TOOL KIT
0639003870 TOOL KIT
0639003970 TOOL KIT
0639004070 TOOL KIT
0639004270 TOOL KIT
相关代理商/技术参数
参数描述
0639003770 功能描述:TOOL KIT RoHS:是 类别:工具 >> 压接器，施用器，压力机 - 配件 系列:* 标准包装:1 系列:- 其它名称:512A512A-NDQ1137690B
0639003800 功能描述:FINE ADJUST APPLICATOR RoHS:是 类别:工具 >> 压接器，施用器，压力机 系列:FineAdjust™, MicroBlade™ 产品培训模块:Board-to-Wire Connectors 标准包装:1 系列:DF11 工具类型:台式压机，施用器 适用于相关产品:矩形触点，24-28 AWG 特点:- 配用:H1505TR-ND - CONN SOCKET 24-28AWG CRIMP GOLDH1504TR-ND - CONN SOCKET 24-28AWG CRIMP TIN 相关产品:AP105-DF11-2428S(64)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(63)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(62)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(61)-ND - TOOL APPLICATOR DF11 ACCESSORIESCM-105 WITH TRANSFORMER-ND - TOOL AUTO CRIMPING MACHINE 其它名称:*AP105-DF11-2428SQ1139807AQ949366
0639003870 功能描述:TOOL KIT RoHS:是 类别:工具 >> 压接器，施用器，压力机 - 配件 系列:* 标准包装:1 系列:- 其它名称:512A512A-NDQ1137690B
0639003900 功能描述:FINE ADJUST APPLICATOR RoHS:是 类别:工具 >> 压接器，施用器，压力机 系列:FineAdjust™, MicroBlade™ 产品培训模块:Board-to-Wire Connectors 标准包装:1 系列:DF11 工具类型:台式压机，施用器 适用于相关产品:矩形触点，24-28 AWG 特点:- 配用:H1505TR-ND - CONN SOCKET 24-28AWG CRIMP GOLDH1504TR-ND - CONN SOCKET 24-28AWG CRIMP TIN 相关产品:AP105-DF11-2428S(64)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(63)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(62)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(61)-ND - TOOL APPLICATOR DF11 ACCESSORIESCM-105 WITH TRANSFORMER-ND - TOOL AUTO CRIMPING MACHINE 其它名称:*AP105-DF11-2428SQ1139807AQ949366
0639003970 功能描述:TOOL KIT RoHS:是 类别:工具 >> 压接器，施用器，压力机 - 配件 系列:* 标准包装:1 系列:- 其它名称:512A512A-NDQ1137690B
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*