- 您现在的位置：买卖IC网 > Datasheet目录581 > 0639003700 (Molex Inc)TOOL CRIMPER 28-32AWG 1.25MM Datasheet资料下载
参数资料
| 型号： | 0639003700 |
| 厂商： | Molex Inc |
| 文件页数： | 12/50页 |
| 文件大小： | 0K |
| 描述： | TOOL CRIMPER 28-32AWG 1.25MM |
| RoHS指令信息： | 0639003700 Cert of Compliance |
| 标准包装： | 1 |
| 系列： | FineAdjust™, PicoBlade™ |
| 工具类型： | 台式压机，施用器 |
| 适用于相关产品： | 刀片型触点，26-32 AWG |
| 配用： | 0500588300-ND - 1.25 W/B TERMINAL(NEW) WM1775TR-ND - CONN TERM FEMALE 28-32AWG TIN WM1142CT-ND - CONN TERM FEMALE 26-28AWG TIN WM1142TR-ND - CONN TERM FEMALE 26-28AWG TIN WM1775CT-ND - CONN TERM FEMALE 28-32AWG TIN |
| 相关产品： | WM3459-ND - TM3000 220V/50HZ PRESS TO 10AWG WM6378-ND - PRESS TM4000 UP TO 4AWG 240AC WM4793-ND - CRMP PRESS TM3000 120V TO 10AWG |
| 其它名称： | 63900-3700 639003700 WM4245 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页当前第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页
FineAdjust Applicator
c. Slide the applicator onto the quick-change mounting plate
until the two notches on the left side engage against the
stops, and at the same time, guide the lug bolt into the
adapter on the press. See Figure 2-2.
LOCKING CLAMP
5
6
d. To lock applicator, turn the M5 SHCS counter clockwise until
tight.
Some presses have locking latches on the quick change
mounting plate, which have to be flipped up to secure the
applicator. Others have knurled finger screws or "T" type latches.
Most of these are located on the right side of the quick change
mounting plate to secure the position of the applicator. These
must be in place and secured before operating the press.
Replace the press guards.
ENGAGE PRESS
YOKE
APPLICATOR
Remove the applicator by reversing the previous steps. When storing
an applicator, always leave a strip of terminals in the applicator to
prevent damage to the tooling. See Section 3.5 Storage.
LOCATOR
CLAMPS
Fitting Terminal Strip
QUICK
CHANGE
M5 SHCS
1. The specified terminals are printed on the setup sheet for the
applicator. Only use the Molex terminals on the setup sheet
MOUNTING
PLATE
Figure 2-2
BASE PLATE
which is supplied with the applicator.
2. Always disconnect the power supply from the press. Remove the machine guards if necessary.
3. Rotate the drag release until the drag frame is in the upright position. This will allow the terminal to slide with ease through
the applicator track. See Figure 2-3.
4. Push the terminal strip until the first terminal comes to rest centered above the anvil.
5. Rotate the drag release to engage the terminal drag frame.
6. Cycle the press by hand so that the feed finger transfers the next terminal to a centered position over the anvil. Check that
all other parts slide and engage without any interference. It is recommended to go through this procedure several times.
TERMINAL
STRIP
Figure 2-4
DRAG RELEASE
FEED FINGER
Figure 2-3
1 ST TERMINAL
CENTERED
ABOVE ANVILS
RELEASE M4 SHCS
7. When unloading the terminal strip, make sure the power is turned off and disconnected from the press. Remove the
machine guards if necessary.
8. Rotate the drag release until the drag frame is in the upright position.
9. Raise feed finger and pull terminal strip back until disengaged from applicator track. See Figure 2-3. If preferred, cut the
terminal carrier strip and pull it through the applicator with needle nose pliers.
10. Replace the machine guards before operating the press.
Doc. No: TM-638004900
Revision: G
Release Date: 09-04-03
Revision Date: 01-15-13
UNCONTROLLED COPY
Page 12 of 50
相关PDF资料 |
PDF描述 |
|---|---|
| 0639003770 | TOOL KIT |
| 0639003870 | TOOL KIT |
| 0639003970 | TOOL KIT |
| 0639004070 | TOOL KIT |
| 0639004270 | TOOL KIT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 0639003770 | 功能描述:TOOL KIT RoHS:是 类别:工具 >> 压接器，施用器，压力机 - 配件 系列:* 标准包装:1 系列:- 其它名称:512A512A-NDQ1137690B |
| 0639003800 | 功能描述:FINE ADJUST APPLICATOR RoHS:是 类别:工具 >> 压接器，施用器，压力机 系列:FineAdjust™, MicroBlade™ 产品培训模块:Board-to-Wire Connectors 标准包装:1 系列:DF11 工具类型:台式压机，施用器 适用于相关产品:矩形触点，24-28 AWG 特点:- 配用:H1505TR-ND - CONN SOCKET 24-28AWG CRIMP GOLDH1504TR-ND - CONN SOCKET 24-28AWG CRIMP TIN 相关产品:AP105-DF11-2428S(64)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(63)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(62)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(61)-ND - TOOL APPLICATOR DF11 ACCESSORIESCM-105 WITH TRANSFORMER-ND - TOOL AUTO CRIMPING MACHINE 其它名称:*AP105-DF11-2428SQ1139807AQ949366 |
| 0639003870 | 功能描述:TOOL KIT RoHS:是 类别:工具 >> 压接器，施用器，压力机 - 配件 系列:* 标准包装:1 系列:- 其它名称:512A512A-NDQ1137690B |
| 0639003900 | 功能描述:FINE ADJUST APPLICATOR RoHS:是 类别:工具 >> 压接器，施用器，压力机 系列:FineAdjust™, MicroBlade™ 产品培训模块:Board-to-Wire Connectors 标准包装:1 系列:DF11 工具类型:台式压机，施用器 适用于相关产品:矩形触点，24-28 AWG 特点:- 配用:H1505TR-ND - CONN SOCKET 24-28AWG CRIMP GOLDH1504TR-ND - CONN SOCKET 24-28AWG CRIMP TIN 相关产品:AP105-DF11-2428S(64)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(63)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(62)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(61)-ND - TOOL APPLICATOR DF11 ACCESSORIESCM-105 WITH TRANSFORMER-ND - TOOL AUTO CRIMPING MACHINE 其它名称:*AP105-DF11-2428SQ1139807AQ949366 |
| 0639003970 | 功能描述:TOOL KIT RoHS:是 类别:工具 >> 压接器，施用器，压力机 - 配件 系列:* 标准包装:1 系列:- 其它名称:512A512A-NDQ1137690B |
发布紧急采购，3分钟左右您将得到回复。