- 您现在的位置：买卖IC网 > Datasheet目录581 > 0639003700 (Molex Inc)TOOL CRIMPER 28-32AWG 1.25MM Datasheet资料下载
参数资料
| 型号： | 0639003700 |
| 厂商： | Molex Inc |
| 文件页数： | 16/50页 |
| 文件大小： | 0K |
| 描述： | TOOL CRIMPER 28-32AWG 1.25MM |
| RoHS指令信息： | 0639003700 Cert of Compliance |
| 标准包装： | 1 |
| 系列： | FineAdjust™, PicoBlade™ |
| 工具类型： | 台式压机，施用器 |
| 适用于相关产品： | 刀片型触点，26-32 AWG |
| 配用： | 0500588300-ND - 1.25 W/B TERMINAL(NEW) WM1775TR-ND - CONN TERM FEMALE 28-32AWG TIN WM1142CT-ND - CONN TERM FEMALE 26-28AWG TIN WM1142TR-ND - CONN TERM FEMALE 26-28AWG TIN WM1775CT-ND - CONN TERM FEMALE 28-32AWG TIN |
| 相关产品： | WM3459-ND - TM3000 220V/50HZ PRESS TO 10AWG WM6378-ND - PRESS TM4000 UP TO 4AWG 240AC WM4793-ND - CRMP PRESS TM3000 120V TO 10AWG |
| 其它名称： | 63900-3700 639003700 WM4245 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页
FineAdjust Applicator
Insulation Crimp Punch Adjustment
1. Place a stripped length of the appropriate wire into the terminal and
crimp under power.
2. Observe quality of insulation crimp and measure the crimp height.
See Appendix A.4, Insulation Crimp.
3. If adjustments are necessary, always turn off and disconnect the
power supply from the press. Remove the machine guards.
4. Rotate the insulation-adjusting cam to achieve the desired insulation
height. Each increment represents approximately 0.06mm (.0025") for
a total adjustment of 3.00mm (.118"). The "1" setting is for the highest
(most loose) crimp height and the "29" setting the lowest (most tight)
crimp height.
5. Repeat the previous steps until the desired insulation height is
obtained.
Figure 2-12
WIRE STOP
M5 SHCS
Note: Due to the large variety of insulation wall thickness, materials, and diameter, Molex does not specify insulation crimp
height. For each different wire type, the insulation crimp height can be measured, recorded, and inspected as a quality indicator.
Wire Stop Adjustment
For automatic wire processing machines, the wire stop can be used to assist in the stripping of the terminal from the punches.
However, in certain circumstances the wire stop will need to be removed when running on an automated machine.
1.
2.
3.
4.
5.
6.
Check the setup documents to obtain the correct strip length.
Place the correct wire into the terminal and crimp the wire under power.
Observe quality of crimp and the wire position. See Appendix A.1 Conductor Brush and Terminal Position.
If adjustments are necessary, turn off and disconnect the power supply from the press. Remove the machine guards.
Use a 4mm hex wrench to loosen the M5 SHCS located on the side of the frame. See Figure 2-12.
Adjust the position of the wire stop by moving the wire stop, towards the operator decreases the brush length and towards
the press increases it.
7. Tighten the M5 SHCS.
8. Hand cycle the press to ensure the applicator is functioning properly. Then crimp a terminal under power and observe the
quality of the termination.
2.4 Crimp Tooling Installation and Removal
Installation and Removal of the Upper Tooling (Punches)
Caution: Always disconnect power supply before installing or
removing tooling.
RAM
PUNCH RELEASE
BUTTON
SCREWDRIVER
NOTE: Always clean mounting surfaces of crimp tooling and tooling holders
before installation.
1. Always turn off and disconnect the power supply from the press. Remove
the machine guards if necessary.
2. Remove the applicator from the press. See Section 2.2, Applicator
Installation and Removal.
PUNCHES
Figure 2-13
3. Pull back the feed arm and remove the ram from the applicator.
4. With a small screw driver, push in the punch release button located on the front of the ram. See Figure 2-13.
5. Pull the punches out the bottom of the ram.
6. Reverse the previous steps to reinstall the punches.
Doc. No: TM-638004900
Revision: G
Release Date: 09-04-03
Revision Date: 01-15-13
UNCONTROLLED COPY
Page 16 of 50
相关PDF资料 |
PDF描述 |
|---|---|
| 0639003770 | TOOL KIT |
| 0639003870 | TOOL KIT |
| 0639003970 | TOOL KIT |
| 0639004070 | TOOL KIT |
| 0639004270 | TOOL KIT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 0639003770 | 功能描述:TOOL KIT RoHS:是 类别:工具 >> 压接器，施用器，压力机 - 配件 系列:* 标准包装:1 系列:- 其它名称:512A512A-NDQ1137690B |
| 0639003800 | 功能描述:FINE ADJUST APPLICATOR RoHS:是 类别:工具 >> 压接器，施用器，压力机 系列:FineAdjust™, MicroBlade™ 产品培训模块:Board-to-Wire Connectors 标准包装:1 系列:DF11 工具类型:台式压机，施用器 适用于相关产品:矩形触点，24-28 AWG 特点:- 配用:H1505TR-ND - CONN SOCKET 24-28AWG CRIMP GOLDH1504TR-ND - CONN SOCKET 24-28AWG CRIMP TIN 相关产品:AP105-DF11-2428S(64)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(63)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(62)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(61)-ND - TOOL APPLICATOR DF11 ACCESSORIESCM-105 WITH TRANSFORMER-ND - TOOL AUTO CRIMPING MACHINE 其它名称:*AP105-DF11-2428SQ1139807AQ949366 |
| 0639003870 | 功能描述:TOOL KIT RoHS:是 类别:工具 >> 压接器，施用器，压力机 - 配件 系列:* 标准包装:1 系列:- 其它名称:512A512A-NDQ1137690B |
| 0639003900 | 功能描述:FINE ADJUST APPLICATOR RoHS:是 类别:工具 >> 压接器，施用器，压力机 系列:FineAdjust™, MicroBlade™ 产品培训模块:Board-to-Wire Connectors 标准包装:1 系列:DF11 工具类型:台式压机，施用器 适用于相关产品:矩形触点，24-28 AWG 特点:- 配用:H1505TR-ND - CONN SOCKET 24-28AWG CRIMP GOLDH1504TR-ND - CONN SOCKET 24-28AWG CRIMP TIN 相关产品:AP105-DF11-2428S(64)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(63)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(62)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(61)-ND - TOOL APPLICATOR DF11 ACCESSORIESCM-105 WITH TRANSFORMER-ND - TOOL AUTO CRIMPING MACHINE 其它名称:*AP105-DF11-2428SQ1139807AQ949366 |
| 0639003970 | 功能描述:TOOL KIT RoHS:是 类别:工具 >> 压接器，施用器，压力机 - 配件 系列:* 标准包装:1 系列:- 其它名称:512A512A-NDQ1137690B |
发布紧急采购，3分钟左右您将得到回复。