- 您现在的位置：买卖IC网 > Datasheet目录581 > 0639003700 (Molex Inc)TOOL CRIMPER 28-32AWG 1.25MM Datasheet资料下载
参数资料
| 型号： | 0639003700 |
| 厂商： | Molex Inc |
| 文件页数： | 43/50页 |
| 文件大小： | 0K |
| 描述： | TOOL CRIMPER 28-32AWG 1.25MM |
| RoHS指令信息： | 0639003700 Cert of Compliance |
| 标准包装： | 1 |
| 系列： | FineAdjust™, PicoBlade™ |
| 工具类型： | 台式压机，施用器 |
| 适用于相关产品： | 刀片型触点，26-32 AWG |
| 配用： | 0500588300-ND - 1.25 W/B TERMINAL(NEW) WM1775TR-ND - CONN TERM FEMALE 28-32AWG TIN WM1142CT-ND - CONN TERM FEMALE 26-28AWG TIN WM1142TR-ND - CONN TERM FEMALE 26-28AWG TIN WM1775CT-ND - CONN TERM FEMALE 28-32AWG TIN |
| 相关产品： | WM3459-ND - TM3000 220V/50HZ PRESS TO 10AWG WM6378-ND - PRESS TM4000 UP TO 4AWG 240AC WM4793-ND - CRMP PRESS TM3000 120V TO 10AWG |
| 其它名称： | 63900-3700 639003700 WM4245 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页当前第43页第44页第45页第46页第47页第48页第49页第50页
FineAdjust Applicator
A.5 Pull Force Testing
A.5.1 Pull Force Procedure
Wire connectors and soldering lugs for use with copper conductors. (Per UL486A November 15, 2003) UL Section 12
Pullout Test.
12.1 The connectors subjected to the static heating test or secureness test shall be subjected to a direct pull of the value
specified for one minute. Only those connectors that have been subjected to the secureness test are to be subjected
to the pullout test. The connector is acceptable if it does not become separated from the conductor or conductors after
completion of the test.
12.2 For an insulated connector in which the insulation is assembled to the connector during installation, the test should be
conducted with the insulation in place if it is always supplied with the connector by the manufacturer. Otherwise, the
test should be conducted without the insulation assembled to the connector. Breaking or tearing of the insulation of an
insulated connector is acceptable in the pullout test. The pull is to be exerted by means of a tension testing machine
or equivalent, so that there will be no sudden application of force or jerking during the test.
The following is the procedure Molex uses for the qualification of pull force:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
Cut wire length approximately 150mm (6.0”) long.
Strip one end to 13mm (.50”), or long enough so no wire insulation is under the insulation grip.
Terminate the appropriate terminal to the wire to the nominal crimp height.
Visually inspect the termination for bell mouth, wire brush, and cut strands.
Set pull tester to 25.4mm (1.0”) per minute. For most applications, a higher rate will not have a significant impact on the
data. Verify higher pull rates with data taken at 25.4mm (1.0”) per minute.
Knot the non-terminated end of the wire.
Regardless of pull tester type, both wire and terminated end must be securely clamped. (Note: When clamping the
terminated end, do not clamp the conductor crimp.)
Activate pull test.
Record a minimum of 25 readings of maximum pull force. After the application has been qualified, a minimum of 5 pull
force measurements should be done to confirm each setup.
Compare lowest reading to minimum pull force specification.
A.5.2
Pull Test Problems
A.5.2.1 Wire breaks before conductor grip. Pull force low
Material Evaluation
Cause: Wire material properties, and/or coatings.
Solution: Test non-terminated wire for breaking strength. Change wire, if
necessary.
Test Values For Pullout Test UL486A
Conductor Size Pullout Force
AWG mm 2 N LBF
30 0.05 6.7 1.5
28 0.08 8.9 2
Stripping Evaluation
Cause: Cut or nicked strands from stripping operation.
1) Wire being manually stripped.
2) Poor automatic stripping cutoff.
3) Worn strip tooling.
Solution: 1) Switch to semiautomatic or automatic wire stripping machine.
2) Correct stripping machine setup.
A.5.2.2 Wire pulls out of conductor grip, crimp height good
26
24
22
20
18
16
14
12
10
9
0.13
0.20
0.324
0.519
0.823
1.31
2.08
3.31
5.261
8.367
13.4
22.3
35.6
57.9
89.0
133.5
222.6
311.5
356.0
400.5
3
5
8
13
20
30
50
70
80
90
Material Evaluation
Cause:
1) Terminal material thickness too small.
Doc. No: TM-638004900
Revision: G
Release Date: 09-04-03
Revision Date: 01-15-13
UNCONTROLLED COPY
Page 43 of 50
相关PDF资料 |
PDF描述 |
|---|---|
| 0639003770 | TOOL KIT |
| 0639003870 | TOOL KIT |
| 0639003970 | TOOL KIT |
| 0639004070 | TOOL KIT |
| 0639004270 | TOOL KIT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 0639003770 | 功能描述:TOOL KIT RoHS:是 类别:工具 >> 压接器，施用器，压力机 - 配件 系列:* 标准包装:1 系列:- 其它名称:512A512A-NDQ1137690B |
| 0639003800 | 功能描述:FINE ADJUST APPLICATOR RoHS:是 类别:工具 >> 压接器，施用器，压力机 系列:FineAdjust™, MicroBlade™ 产品培训模块:Board-to-Wire Connectors 标准包装:1 系列:DF11 工具类型:台式压机，施用器 适用于相关产品:矩形触点，24-28 AWG 特点:- 配用:H1505TR-ND - CONN SOCKET 24-28AWG CRIMP GOLDH1504TR-ND - CONN SOCKET 24-28AWG CRIMP TIN 相关产品:AP105-DF11-2428S(64)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(63)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(62)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(61)-ND - TOOL APPLICATOR DF11 ACCESSORIESCM-105 WITH TRANSFORMER-ND - TOOL AUTO CRIMPING MACHINE 其它名称:*AP105-DF11-2428SQ1139807AQ949366 |
| 0639003870 | 功能描述:TOOL KIT RoHS:是 类别:工具 >> 压接器，施用器，压力机 - 配件 系列:* 标准包装:1 系列:- 其它名称:512A512A-NDQ1137690B |
| 0639003900 | 功能描述:FINE ADJUST APPLICATOR RoHS:是 类别:工具 >> 压接器，施用器，压力机 系列:FineAdjust™, MicroBlade™ 产品培训模块:Board-to-Wire Connectors 标准包装:1 系列:DF11 工具类型:台式压机，施用器 适用于相关产品:矩形触点，24-28 AWG 特点:- 配用:H1505TR-ND - CONN SOCKET 24-28AWG CRIMP GOLDH1504TR-ND - CONN SOCKET 24-28AWG CRIMP TIN 相关产品:AP105-DF11-2428S(64)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(63)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(62)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(61)-ND - TOOL APPLICATOR DF11 ACCESSORIESCM-105 WITH TRANSFORMER-ND - TOOL AUTO CRIMPING MACHINE 其它名称:*AP105-DF11-2428SQ1139807AQ949366 |
| 0639003970 | 功能描述:TOOL KIT RoHS:是 类别:工具 >> 压接器，施用器，压力机 - 配件 系列:* 标准包装:1 系列:- 其它名称:512A512A-NDQ1137690B |
发布紧急采购，3分钟左右您将得到回复。