收藏本站
参数资料
型号： 0639003700
厂商： Molex Inc
文件页数： 14/50页
文件大小： 0K
描述： TOOL CRIMPER 28-32AWG 1.25MM
RoHS指令信息： 0639003700 Cert of Compliance
标准包装： 1
系列： FineAdjust™, PicoBlade™
工具类型： 台式压机，施用器
适用于相关产品： 刀片型触点，26-32 AWG
配用： 0500588300-ND - 1.25 W/B TERMINAL(NEW)
WM1775TR-ND - CONN TERM FEMALE 28-32AWG TIN
WM1142CT-ND - CONN TERM FEMALE 26-28AWG TIN
WM1142TR-ND - CONN TERM FEMALE 26-28AWG TIN
WM1775CT-ND - CONN TERM FEMALE 28-32AWG TIN
相关产品： WM3459-ND - TM3000 220V/50HZ PRESS TO 10AWG
WM6378-ND - PRESS TM4000 UP TO 4AWG 240AC
WM4793-ND - CRMP PRESS TM3000 120V TO 10AWG
其它名称： 63900-3700
639003700
WM4245
FineAdjust Applicator
3.
7
8
9
Put a regular screwdriver through the hole in the lock screw and turn the adjusting screw to position the terminal in the
correct location. See Figure 2-7. Turning the screw clockwise will move the track towards the operator; to move the track
towards the applicator turn the screw counterclockwise. Depending on the amount of movement, the feed finger mount may
need to be loosened and readjusted. See Feed Finger adjustment.
To lock the track in position, tighten the M10 lock screw.
If the feed finger mount was loosened during the track positioning, remember to tighten its mounting screw.
Replace machine guards.
10 Hand cycle the press to ensure the terminal is positioned properly on the anvils and does not have an excessive cutoff tab.
Also, verify the terminal feed operation.
11 Restore power to the press, crimp a terminal under power, and observe the quality of the termination.
12 Repeat the above steps until the desired terminal position is obtained.
Feed Finger Adjustments
1. Position the feed finger to properly feed the next terminal in
position. Typically, terminals are fed by the carrier strip.
2. Depending on the feed cam installation (pre-feed or post-
feed), move the press ram until the feed is forward (this makes
the feed finger mount more accessible), and then disconnect
power from the press. Remove the machine guards if
necessary.
3. Using a 2.5mm hex wrench, loosen the M3 SHCS located on
the feed finger mount. While holding the feed finger lever
PUSH DOWN
M3 SHCS
down slightly, slide the feed finger to the desired position. See
Figure 2-8.
4. If the feed finger mount cannot be moved far enough, remove
the M3 SHCS completely and install it in another tapped hole
FEED FINGER
LEVER
Figure 2-8
TERMINAL
FEED FINGER
FEED FINGER
MOUNT
in the feed finger lever. In addition, the feed finger mount can be reversed (the feed finger must be reversed as well) to gain
additional adjustment.
5. Tighten the M3 SHCS to lock the feed finger in position.
Feed Stroke Cam Adjustments
Feed Cam
Order No.
Press Stroke
mm In.
Feed Timing
1. The terminal feed stroke is driven by a cam mounted to the applicator
ram. Two feed cams are shipped with the applicator. The standard cam
is installed in the applicator. The spare cam is for presses with short
strokes (for example, 28mm). Using the standard cam with a short-
stroke press may result in insufficient feed stroke or incorrect feed
timing.
63800-0305
41.28 1-5/8
28.58 1-1/8
Up stroke
(terminal present
over anvil)
2. Determine what feed timing is desired. Typically, when the applicator is
mounted in a wire processing machine, the feed stroke cam should be
assembled in the down stroke position. While the press is idle in the up
41.28 1-5/8
Down stroke
(terminal not present
position, a terminal will not be present over the anvil. For most bench
applications, the cam is installed in the up stroke position. This will leave
a terminal over the anvil when the press is idle in the up position. See
Figure 2-9.
3. Turn off and disconnect the power supply from the press. Remove the
63800-0305
over anvil)
Down stroke
machine guards if necessary.
4. Remove the applicator from the press. See Applicator Installation and
28.58 1-1/8
(terminal not present
over anvil)
Removal.
5. Pull back on the feed pivot lever and remove the ram from the applicator.
6. Holding on to the ram, use a 3mm hex wrench to remove the M4 SHCS
11-18-4238
Figure 2-9
holding the cam on the back of the ram.
7. Position the cam in the desired position for feeding and attach with the M4 screw. See Figure 2-9.
Doc. No: TM-638004900
Revision: G
Release Date: 09-04-03
Revision Date: 01-15-13
UNCONTROLLED COPY
Page 14 of 50
相关PDF资料
PDF描述
0639003770 TOOL KIT
0639003870 TOOL KIT
0639003970 TOOL KIT
0639004070 TOOL KIT
0639004270 TOOL KIT
相关代理商/技术参数
参数描述
0639003770 功能描述:TOOL KIT RoHS:是 类别:工具 >> 压接器，施用器，压力机 - 配件 系列:* 标准包装:1 系列:- 其它名称:512A512A-NDQ1137690B
0639003800 功能描述:FINE ADJUST APPLICATOR RoHS:是 类别:工具 >> 压接器，施用器，压力机 系列:FineAdjust™, MicroBlade™ 产品培训模块:Board-to-Wire Connectors 标准包装:1 系列:DF11 工具类型:台式压机，施用器 适用于相关产品:矩形触点，24-28 AWG 特点:- 配用:H1505TR-ND - CONN SOCKET 24-28AWG CRIMP GOLDH1504TR-ND - CONN SOCKET 24-28AWG CRIMP TIN 相关产品:AP105-DF11-2428S(64)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(63)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(62)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(61)-ND - TOOL APPLICATOR DF11 ACCESSORIESCM-105 WITH TRANSFORMER-ND - TOOL AUTO CRIMPING MACHINE 其它名称:*AP105-DF11-2428SQ1139807AQ949366
0639003870 功能描述:TOOL KIT RoHS:是 类别:工具 >> 压接器，施用器，压力机 - 配件 系列:* 标准包装:1 系列:- 其它名称:512A512A-NDQ1137690B
0639003900 功能描述:FINE ADJUST APPLICATOR RoHS:是 类别:工具 >> 压接器，施用器，压力机 系列:FineAdjust™, MicroBlade™ 产品培训模块:Board-to-Wire Connectors 标准包装:1 系列:DF11 工具类型:台式压机，施用器 适用于相关产品:矩形触点，24-28 AWG 特点:- 配用:H1505TR-ND - CONN SOCKET 24-28AWG CRIMP GOLDH1504TR-ND - CONN SOCKET 24-28AWG CRIMP TIN 相关产品:AP105-DF11-2428S(64)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(63)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(62)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(61)-ND - TOOL APPLICATOR DF11 ACCESSORIESCM-105 WITH TRANSFORMER-ND - TOOL AUTO CRIMPING MACHINE 其它名称:*AP105-DF11-2428SQ1139807AQ949366
0639003970 功能描述:TOOL KIT RoHS:是 类别:工具 >> 压接器，施用器，压力机 - 配件 系列:* 标准包装:1 系列:- 其它名称:512A512A-NDQ1137690B
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*