- 您现在的位置：买卖IC网 > PDF目录21903 > 4430-T-B1 D 950 (Silicon Laboratories Inc)KIT DEV TEST EZRADIOPRO SI4430 PDF资料下载
参数资料
| 型号： | 4430-T-B1 D 950 |
| 厂商： | Silicon Laboratories Inc |
| 文件页数： | 21/47页 |
| 文件大小： | 799K |
| 描述： | KIT DEV TEST EZRADIOPRO SI4430 |
| 标准包装： | 1 |
| 附件类型： | 测试卡，收发器，950MHz |
| 适用于相关产品： | EZRadioPRO? |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页当前第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页
Si4430/31/32-B1
Rev 1.1
21
3.2.1. SHUTDOWN State
The SHUTDOWN state is the lowest current consumption state of the device with nominally less than 15 nA of
current consumption. The shutdown state may be entered by driving the SDN pin (Pin 20) high. The SDN pin
should be held low in all states except the SHUTDOWN state. In the SHUTDOWN state, the contents of the
registers are lost and there is no SPI access.
When the chip is connected to the power supply, a POR will be initiated after the falling edge of SDN.
3.2.2. IDLE State
There are five different modes in the IDLE state which may be selected by "Register 07h. Operating Mode and
Function Control 1". All modes have a tradeoff between current consumption and response time to TX/RX mode.
This tradeoff is shown in Table 11. After the POR event, SWRESET, or exiting from the SHUTDOWN state the chip
will default to the IDLE-READY mode. After a POR event the interrupt registers must be read to properly enter the
SLEEP, SENSOR, or STANDBY mode and to control the 32 kHz clock correctly.
3.2.2.1. STANDBY Mode
STANDBY mode has the lowest current consumption of the five IDLE states with only the LPLDO enabled to
maintain the register values. In this mode the registers can be accessed in both read and write mode. The
STANDBY mode can be entered by writing 0h to "Register 07h. Operating Mode and Function Control 1". If an
interrupt has occurred (i.e., the nIRQ pin = 0) the interrupt registers must be read to achieve the minimum current
consumption. Additionally, the ADC should not be selected as an input to the GPIO in this mode as it will cause
excess current consumption.
3.2.2.2. SLEEP Mode
In SLEEP mode the LPLDO is enabled along with the Wake-Up-Timer, which can be used to accurately wake-up
the radio at specified intervals. See "8.6. Wake-Up Timer and 32 kHz Clock Source" on page 56 for more
information on the Wake-Up-Timer. SLEEP mode is entered by setting enwt = 1 (40h) in "Register 07h. Operating
Mode and Function Control 1". If an interrupt has occurred (i.e., the nIRQ pin = 0) the interrupt registers must be
read to achieve the minimum current consumption. Also, the ADC should not be selected as an input to the GPIO
in this mode as it will cause excess current consumption.
3.2.2.3. SENSOR Mode
In SENSOR mode either the Low Battery Detector, Temperature Sensor, or both may be enabled in addition to the
LPLDO and Wake-Up-Timer. The Low Battery Detector can be enabled by setting enlbd = 1 in "Register 07h.
Operating Mode and Function Control 1". See "8.4. Temperature Sensor" on page 53 and "8.5. Low Battery
Detector" on page 55 for more information on these features. If an interrupt has occurred (i.e., the nIRQ pin = 0)
the interrupt registers must be read to achieve the minimum current consumption.
3.2.2.4. READY Mode
READY Mode is designed to give a fast transition time to TX mode with reasonable current consumption. In this
mode the Crystal oscillator remains enabled reducing the time required to switch to TX or RX mode by eliminating
the crystal start-up time. READY mode is entered by setting xton = 1 in "Register 07h. Operating Mode and
Function Control 1". To achieve the lowest current consumption state the crystal oscillator buffer should be
disabled in Register 62h. Crystal Oscillator Control and Test. To exit READY mode, bufovr (bit 1) of this register
must be set back to 0.
3.2.2.5. TUNE Mode
In TUNE mode the PLL remains enabled in addition to the other blocks enabled in the IDLE modes. This will give
the fastest response to TX mode as the PLL will remain locked but it results in the highest current consumption.
This mode of operation is designed for frequency hopping spread spectrum systems (FHSS). TUNE mode is
entered by setting pllon = 1 in "Register 07h. Operating Mode and Function Control 1". It is not necessary to set
xton to 1 for this mode, the internal state machine automatically enables the crystal oscillator.
相关PDF资料 |
PDF描述 |
|---|---|
| B82432X2 | KIT INDUCTOR 1812-C SERIES |
| XPGWHT-L1-0000-00BE8 | LED WARM WHITE 2700K SMD |
| B82422X100 | KIT INDUCTOR 1210-A SERIES |
| B82422X1 | KIT INDUCTOR 1210-T SERIES |
| B82559X1 | KIT INDUCTOR POWER 82559 SERIES |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 4431 | 制造商:Thomas & Betts 功能描述:TRIPLE HEX DIE 制造商:Thomas & Betts 功能描述:Triple Hex Die |
| 4431.1001 | 功能描述:摇臂开关与扳钮开关 UV PROTECTION SWITCH Rocker, 230V 50HZ RoHS:否 制造商:C&K Components 触点形式: 开关功能: 电流额定值:50 mA 电压额定值 AC: 电压额定值 DC:30 V 功率额定值: 端接类型: 执行器:Paddle 颜色: 安装风格:Panel 端子密封: 触点电镀: 照明:Not Illuminated 照明颜色: |
| 4431.1002 | 功能描述:摇臂开关与扳钮开关 UV PROTECTION SWITCH Rocker, 115V 50HZ RoHS:否 制造商:C&K Components 触点形式: 开关功能: 电流额定值:50 mA 电压额定值 AC: 电压额定值 DC:30 V 功率额定值: 端接类型: 执行器:Paddle 颜色: 安装风格:Panel 端子密封: 触点电镀: 照明:Not Illuminated 照明颜色: |
| 4431.1003 | 功能描述:摇臂开关与扳钮开关 UV PROTECTION SWITCH Rocker, 120V 60HZ RoHS:否 制造商:C&K Components 触点形式: 开关功能: 电流额定值:50 mA 电压额定值 AC: 电压额定值 DC:30 V 功率额定值: 端接类型: 执行器:Paddle 颜色: 安装风格:Panel 端子密封: 触点电镀: 照明:Not Illuminated 照明颜色: |
| 4431.1004 | 功能描述:摇臂开关与扳钮开关 UV PROTECTION SWITCH Rocker, 230V 50HZ RoHS:否 制造商:C&K Components 触点形式: 开关功能: 电流额定值:50 mA 电压额定值 AC: 电压额定值 DC:30 V 功率额定值: 端接类型: 执行器:Paddle 颜色: 安装风格:Panel 端子密封: 触点电镀: 照明:Not Illuminated 照明颜色: |
发布紧急采购，3分钟左右您将得到回复。