- 您现在的位置：买卖IC网 > PDF目录21903 > 4430-T-B1 D 950 (Silicon Laboratories Inc)KIT DEV TEST EZRADIOPRO SI4430 PDF资料下载
参数资料
| 型号： | 4430-T-B1 D 950 |
| 厂商： | Silicon Laboratories Inc |
| 文件页数： | 40/47页 |
| 文件大小： | 799K |
| 描述： | KIT DEV TEST EZRADIOPRO SI4430 |
| 标准包装： | 1 |
| 附件类型： | 测试卡，收发器，950MHz |
| 适用于相关产品： | EZRadioPRO? |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页当前第40页第41页第42页第43页第44页第45页第46页第47页
Si4430/31/32-B1
40
Rev 1.1
5.8. Crystal Oscillator
The Si4430/31/32 includes an integrated 30 MHz crystal oscillator with a fast start-up time of less than 600 祍
when a suitable parallel resonant crystal is used. The design is differential with the required crystal load
capacitance integrated on-chip to minimize the number of external components. By default, all that is required off-
chip is the 30 MHz crystal.
The crystal load capacitance can be digitally programmed to accommodate crystals with various load capacitance
requirements and to adjust the frequency of the crystal oscillator. The tuning of the crystal load capacitance is
programmed through the xlc[6:0] field of "Register 09h. 30 MHz Crystal Oscillator Load Capacitance." The total
internal capacitance is 12.5 pF and is adjustable in approximately 127 steps (97fF/step). The xtalshift bit provides a
coarse shift in frequency but is not binary with xlc[6:0].
The crystal frequency adjustment can be used to compensate for crystal production tolerances. Utilizing the on-
chip temperature sensor and suitable control software, the temperature dependency of the crystal can be
canceled.
The typical value of the total on-chip capacitance Cint can be calculated as follows:
Cint = 1.8 pF + 0.085 pF x xlc[6:0] + 3.7 pF x xtalshift
Note that the coarse shift bit xtalshift is not binary with xlc[6:0]. The total load capacitance Cload seen by the crystal
can be calculated by adding the sum of all external parasitic PCB capacitances Cext to Cint. If the maximum value
of Cint (16.3 pF) is not sufficient, an external capacitor can be added for exact tuning. Additional information on
calculating Cext and crystal selection guidelines is provided in AN417: Si4x3x Family Crystal Oscillator.
If AFC is disabled then the synthesizer frequency may be further adjusted by programming the Frequency Offset
field fo[9:0]in "Register 73h. Frequency Offset 1" and "Register 74h. Frequency Offset 2", as discussed in "3.5.
Frequency Control" on page 25.
The crystal oscillator frequency is divided down internally and may be output to the microcontroller through one of
the GPIO pins for use as the System Clock. In this fashion, only one crystal oscillator is required for the entire
system and the BOM cost is reduced. The available clock frequencies and GPIO configuration are discussed
further in "8.2. Microcontroller Clock" on page 51.
The Si4430/31/32 may also be driven with an external 30 MHz clock signal through the XOUT pin. When driving
with an external reference or using a TCXO, the XTAL load capacitance register should be set to 0.
5.9. Regulators
There are a total of six regulators integrated onto the Si4430/31/32. With the exception of the digital regulator, all
regulators are designed to operate with only internal decoupling. The digital regulator requires an external 1 礔
decoupling capacitor. All regulators are designed to operate with an input supply voltage from +1.8 to +3.6 V. The
output stage of the of PA is not connected internally to a regulator and is connected directly to the battery voltage.
A supply voltage should only be connected to the VDD pins. No voltage should be forced on the digital regulator
output.
Add R/W Function/Description
D7
D6
D5
D4
D3
D2
D1
D0
POR Def.
09 R/W Crystal Oscillator Load
Capacitance
xtalshift
xlc[6]
xlc[5]
xlc[4]
xlc[3]
xlc[2]
xlc[1]
xlc[0]
7Fh
相关PDF资料 |
PDF描述 |
|---|---|
| B82432X2 | KIT INDUCTOR 1812-C SERIES |
| XPGWHT-L1-0000-00BE8 | LED WARM WHITE 2700K SMD |
| B82422X100 | KIT INDUCTOR 1210-A SERIES |
| B82422X1 | KIT INDUCTOR 1210-T SERIES |
| B82559X1 | KIT INDUCTOR POWER 82559 SERIES |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 4431 | 制造商:Thomas & Betts 功能描述:TRIPLE HEX DIE 制造商:Thomas & Betts 功能描述:Triple Hex Die |
| 4431.1001 | 功能描述:摇臂开关与扳钮开关 UV PROTECTION SWITCH Rocker, 230V 50HZ RoHS:否 制造商:C&K Components 触点形式: 开关功能: 电流额定值:50 mA 电压额定值 AC: 电压额定值 DC:30 V 功率额定值: 端接类型: 执行器:Paddle 颜色: 安装风格:Panel 端子密封: 触点电镀: 照明:Not Illuminated 照明颜色: |
| 4431.1002 | 功能描述:摇臂开关与扳钮开关 UV PROTECTION SWITCH Rocker, 115V 50HZ RoHS:否 制造商:C&K Components 触点形式: 开关功能: 电流额定值:50 mA 电压额定值 AC: 电压额定值 DC:30 V 功率额定值: 端接类型: 执行器:Paddle 颜色: 安装风格:Panel 端子密封: 触点电镀: 照明:Not Illuminated 照明颜色: |
| 4431.1003 | 功能描述:摇臂开关与扳钮开关 UV PROTECTION SWITCH Rocker, 120V 60HZ RoHS:否 制造商:C&K Components 触点形式: 开关功能: 电流额定值:50 mA 电压额定值 AC: 电压额定值 DC:30 V 功率额定值: 端接类型: 执行器:Paddle 颜色: 安装风格:Panel 端子密封: 触点电镀: 照明:Not Illuminated 照明颜色: |
| 4431.1004 | 功能描述:摇臂开关与扳钮开关 UV PROTECTION SWITCH Rocker, 230V 50HZ RoHS:否 制造商:C&K Components 触点形式: 开关功能: 电流额定值:50 mA 电压额定值 AC: 电压额定值 DC:30 V 功率额定值: 端接类型: 执行器:Paddle 颜色: 安装风格:Panel 端子密封: 触点电镀: 照明:Not Illuminated 照明颜色: |
发布紧急采购，3分钟左右您将得到回复。