参数资料
型号: 4430-T-B1 D 950
厂商: Silicon Laboratories Inc
文件页数: 30/47页
文件大小: 799K
描述: KIT DEV TEST EZRADIOPRO SI4430
标准包装: 1
附件类型: 测试卡,收发器,950MHz
适用于相关产品: EZRadioPRO?
Si4430/31/32-B1
30
Rev 1.1
When AFC is enabled, the preamble length needs to be long enough to settle the AFC. In general, one byte of
preamble is sufficient to settle the AFC. Disabling the AFC allows the preamble to be shortened from 40 bits to 32
bits. Note that with the AFC disabled, the preamble length must still be long enough to settle the receiver and to
detect the preamble (see "6.7. Preamble Length" on page 47). The AFC corrects the detected frequency offset by
changing the frequency of the Fractional-N PLL. When the preamble is detected, the AFC will freeze for the
remainder of the packet. In multi-packet mode the AFC is reset at the end of every packet and will re-acquire the
frequency offset for the next packet. The AFC loop includes a bandwidth limiting mechanism improving the
rejection of out of band signals. When the AFC loop is enabled, its pull-in-range is determined by the bandwidth
limiter value (AFCLimiter) which is located in register 2Ah.
AFC_pull_in_range = 盇FCLimiter[7:0] x (hbsel+1) x 625 Hz
The AFC Limiter register is an unsigned register and its value can be obtained from the EZRadioPRO Register
Calculator spreadsheet.
The amount of error correction feedback to the Fractional-N PLL before the preamble is detected is controlled from
afcgearh[2:0]. The default value 000 relates to a feedback of 100% from the measured frequency error and is
advised for most applications. Every bit added will half the feedback but will require a longer preamble to settle.
The AFC operates as follows. The frequency error of the incoming signal is measured over a period of two bit
times, after which it corrects the local oscillator via the Fractional-N PLL. After this correction, some time is allowed
to settle the Fractional-N PLL to the new frequency before the next frequency error is measured. The duration of
the AFC cycle before the preamble is detected can be programmed with shwait[2:0]. It is advised to use the default
value 001, which sets the AFC cycle to 4 bit times (2 for measurement and 2 for settling). If shwait[2:0] is
programmed to 3'b000, there is no AFC correction output. It is advised to use the default value 001, which sets the
AFC cycle to 4 bit times (2 for measurement and 2 for settling).
The AFC correction value may be read from register 2Bh. The value read can be converted to kHz with the
following formula:
AFC Correction = 156.25Hz x (hbsel +1) x afc_corr[7: 0]
Frequency Correction
RX
TX
AFC disabled
Freq Offset Register   Freq Offset Register
AFC enabled
AFC
Freq Offset Register
相关PDF资料
PDF描述
B82432X2 KIT INDUCTOR 1812-C SERIES
XPGWHT-L1-0000-00BE8 LED WARM WHITE 2700K SMD
B82422X100 KIT INDUCTOR 1210-A SERIES
B82422X1 KIT INDUCTOR 1210-T SERIES
B82559X1 KIT INDUCTOR POWER 82559 SERIES
相关代理商/技术参数
参数描述
4431 制造商:Thomas & Betts 功能描述:TRIPLE HEX DIE 制造商:Thomas & Betts 功能描述:Triple Hex Die
4431.1001 功能描述:摇臂开关与扳钮开关 UV PROTECTION SWITCH Rocker, 230V 50HZ RoHS:否 制造商:C&K Components 触点形式: 开关功能: 电流额定值:50 mA 电压额定值 AC: 电压额定值 DC:30 V 功率额定值: 端接类型: 执行器:Paddle 颜色: 安装风格:Panel 端子密封: 触点电镀: 照明:Not Illuminated 照明颜色:
4431.1002 功能描述:摇臂开关与扳钮开关 UV PROTECTION SWITCH Rocker, 115V 50HZ RoHS:否 制造商:C&K Components 触点形式: 开关功能: 电流额定值:50 mA 电压额定值 AC: 电压额定值 DC:30 V 功率额定值: 端接类型: 执行器:Paddle 颜色: 安装风格:Panel 端子密封: 触点电镀: 照明:Not Illuminated 照明颜色:
4431.1003 功能描述:摇臂开关与扳钮开关 UV PROTECTION SWITCH Rocker, 120V 60HZ RoHS:否 制造商:C&K Components 触点形式: 开关功能: 电流额定值:50 mA 电压额定值 AC: 电压额定值 DC:30 V 功率额定值: 端接类型: 执行器:Paddle 颜色: 安装风格:Panel 端子密封: 触点电镀: 照明:Not Illuminated 照明颜色:
4431.1004 功能描述:摇臂开关与扳钮开关 UV PROTECTION SWITCH Rocker, 230V 50HZ RoHS:否 制造商:C&K Components 触点形式: 开关功能: 电流额定值:50 mA 电压额定值 AC: 电压额定值 DC:30 V 功率额定值: 端接类型: 执行器:Paddle 颜色: 安装风格:Panel 端子密封: 触点电镀: 照明:Not Illuminated 照明颜色: