- 您现在的位置：买卖IC网 > PDF目录97839 > 71M6513-IGTR/F (MAXIM INTEGRATED PRODUCTS INC) SPECIALTY ANALOG CIRCUIT, PQFP100 PDF资料下载
参数资料
| 型号： | 71M6513-IGTR/F |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | 模拟信号调理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 封装： | LEAD FREE, LQFP-100 |
| 文件页数： | 42/104页 |
| 文件大小： | 1390K |
| 代理商： | 71M6513-IGTR/F |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页当前第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页
71M6513/71M6513H
3-Phase Energy Meter IC
DATA SHEET
AUGUST 2011
Page: 42 of 104
2005-2011 Teridian Semiconductor Corporation
A Maxim Integrated Products Brand
Oscillator
The oscillator drives a standard 32.768kHz watch crystal (see Figure 9). Crystals of this type are accurate and do not require a
high current oscillator circuit. The oscillator in the 71M6513 Power Meter IC has been designed specifically to handle watch
crystals and is compatible with their high impedance and limited power handling capability. The oscillator power dissipation is
very low to maximize the lifetime of any battery backup device attached to the VBAT pin.
Figure 9: Oscillator Circuit
The oscillator should be placed as close as possible to the IC, and vias should be avoided.
An external resistor across the crystal must not be added.
Real-Time Clock (RTC)
The RTC is driven directly by the crystal oscillator. In the absence of the 3.3V supply, the RTC is powered by the external
battery (VBAT pin). The RTC consists of a counter chain and output registers. The counter chain consists of seconds, minutes,
hours, day of week, day of month, month, and year. The RTC is capable of processing leap years. Each counter has its own
output register. Whenever the MPU reads the seconds register, all other output registers are automatically updated. Since the
RTC clock is not coherent to the MPU clock, the MPU must read the seconds register until two consecutive reads are the
same (requires either 2 or 3 reads). At this point, all RTC output registers will have the correct time. Regardless of the MPU
clock speed, RTC reads require one wait state.
The RTC interrupt must be enabled using the I/O RAM register EX_RTC (address 0x2002[1]). RTC time is set by writing to the
I/O RAM registers RTC_SEC, RTC_MIN, through RTC_YR. Each byte written to RTC must be delayed at least 3 CK32 cycles
from any previous byte written to RTC.
Two time correction bits, the I/O RAM registers RTC_DEC_SEC (0x201C[1]) and RTC_INC_SEC (0x201C[0]) are provided to
adjust the RTC time. A pulse on one of these bits causes the time to be decremented or incremented by an additional second
at the next update of the RTC_SEC register. Thus, if the crystal temperature coefficient is known, the MPU firmware can
integrate temperature and correct the RTC time as necessary as discussed in temperature compensation.
Comparators (V2, V3)
The 71M6513/6513H includes two programmable comparators that are connected to the V2 and V3 pins. The I/O RAM
register COMP_INT (0x2003[4:3]) allows the user to determine if comparators 2 and 3 will trigger an interrupt to the MPU. The
output of each comparator is available in the COMPSTAT register. VBIAS is used as the threshold, and built-in hysteresis
prevents each comparator from repeatedly responding to low-amplitude noise.
Comparators 2 and 3 can be used for early warning of power faults, or for monitoring of battery or other DC voltages. If they
are both selected to interrupt the MPU, their outputs will be XORed together. The voltage at V3 is also available to the ADC in
the AFE, but the comparator should not be used when V3 is used for analog measurements.
Comparator 1 is part of the power fault circuitry (see section V1 Pin) and cannot be programmed.
crystal
XOUT
XIN
71M651X
相关PDF资料 |
PDF描述 |
|---|---|
| 71M6513H-IGT/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 71M6513H-IGTR/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 71M6513-IGT/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 71M6515H-IGTW/F | SPECIALTY ANALOG CIRCUIT, PQFP64 |
| 71M6515H-IGTWR/F | SPECIALTY ANALOG CIRCUIT, PQFP64 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 71M6515H | 制造商:TERIDIAN 制造商全称:TERIDIAN 功能描述:Energy Meter IC |
| 71M6515H_11 | 制造商:TERIDIAN 制造商全称:TERIDIAN 功能描述:Up to 10ppmC precision ultra-stable voltage reference Digital temperature compensation |
| 71M6515H-DB | 功能描述:开发板和工具包 - 8051 71M6515H Demo Brd RoHS:否 制造商:Silicon Labs 产品:Development Kits 工具用于评估:C8051F960, Si7005 核心: 接口类型:USB 工作电源电压: |
| 71M6515H-IGT | 制造商:Maxim Integrated Products 功能描述:METERING FRONT END - Rail/Tube |
| 71M6515H-IGT/F | 功能描述:计量片上系统 - SoC Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。