参数资料
型号: 71M6513-IGTR/F
厂商: MAXIM INTEGRATED PRODUCTS INC
元件分类: 模拟信号调理
英文描述: SPECIALTY ANALOG CIRCUIT, PQFP100
封装: LEAD FREE, LQFP-100
文件页数: 77/104页
文件大小: 1390K
代理商: 71M6513-IGTR/F
71M6513/71M6513H
3-Phase Energy Meter IC
DATA SHEET
AUGUST 2011
Page: 74 of 104
2005-2011 Teridian Semiconductor Corporation
A Maxim Integrated Products Brand
Pulse Generation
Input variables: The combination of the PULSE_SLOW and PULSE_FAST parameters control the speed of the pulse rate. The
default values of 1 and 1 will maintain the original pulse rate given by the Kh equation.
WRATE controls the number of pulses that are generated per measured Wh and VARh quantities. The lower WRATE it is the
slower is the pulse rate for measured power quantity. The metering constant Kh is derived from WRATE as the amount of
energy measured for each pulse. That is, if Kh = 1Wh/pulse, a power applied to the meter of 120V and 30A results in one
pulse per second. If the load is 240V at 150A, ten pulses per second will be generated.
Control is transferred to the MPU for pulse generation if EXT_PULSE > 0. In this case, the pulse rate is determined by
APULSEW and APULSER. The MPU has to load the source for pulse generation in APULSEW and APULSER to generate pulses.
Irrespective of the EXT_PULSE, status the output pulse rate controlled by APULSEW and APULSER is implemented by the CE
only. By setting EXT_PULSE > 0, the MPU is providing the source for pulse generation. If EXT_PULSE is negative, W0SUM_X
and VAR0SUM_X are the default pulse generation sources. In this case, creep cannot be controlled since it is an MPU function.
The maximum pulse rate is 3*FS = 7.56kHz.
PULSE_WIDTH allows adjustment of the pulse width for compatibility with calibration and other external equipment. The
minimum pulse width possible is 66.16s.
The maximum time jitter is 1/6 of the
MUX cycle period (normally 67μs) and is independent of the number of pulses measured.
Thus, if the pulse generator is monitored for 1 second, the peak jitter is 67ppm. After 10 seconds, the peak jitter is 7ppm. The
average jitter is always zero. If it is attempted to drive either pulse generator faster than its maximum rate, it will simply output
at its maximum rate without exhibiting any roll-over characteristics. The actual pulse rate, using WSUM as an example, is:
Hz
F
WSUM
WRATE
X
RATE
S
46
2
=
Where FS = 2520.6Hz (sampling frequency), and X = pulse speed factor derived from CE variables PULSE_SLOW and
PULSE_FAST (see table below).
相关PDF资料
PDF描述
71M6513H-IGT/F SPECIALTY ANALOG CIRCUIT, PQFP100
71M6513H-IGTR/F SPECIALTY ANALOG CIRCUIT, PQFP100
71M6513-IGT/F SPECIALTY ANALOG CIRCUIT, PQFP100
71M6515H-IGTW/F SPECIALTY ANALOG CIRCUIT, PQFP64
71M6515H-IGTWR/F SPECIALTY ANALOG CIRCUIT, PQFP64
相关代理商/技术参数
参数描述
71M6515H 制造商:TERIDIAN 制造商全称:TERIDIAN 功能描述:Energy Meter IC
71M6515H_11 制造商:TERIDIAN 制造商全称:TERIDIAN 功能描述:Up to 10ppmC precision ultra-stable voltage reference Digital temperature compensation
71M6515H-DB 功能描述:开发板和工具包 - 8051 71M6515H Demo Brd RoHS:否 制造商:Silicon Labs 产品:Development Kits 工具用于评估:C8051F960, Si7005 核心: 接口类型:USB 工作电源电压:
71M6515H-IGT 制造商:Maxim Integrated Products 功能描述:METERING FRONT END - Rail/Tube
71M6515H-IGT/F 功能描述:计量片上系统 - SoC Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel