参数资料
型号: 71M6513-IGTR/F
厂商: MAXIM INTEGRATED PRODUCTS INC
元件分类: 模拟信号调理
英文描述: SPECIALTY ANALOG CIRCUIT, PQFP100
封装: LEAD FREE, LQFP-100
文件页数: 45/104页
文件大小: 1390K
代理商: 71M6513-IGTR/F
71M6513/71M6513H
3-Phase Energy Meter IC
DATA SHEET
SEPTEMBER 2011
2005-2011 Teridian Semiconductor Corporation
Page: 45 of 104
A Maxim Integrated Products Brand
Figure 11: Voltage Range for V1
Internal Clocks and Clock Dividers
All internal clocks are based on the watch crystal frequency (CK32 = 32,768Hz) applied to the XIN and XOUT pins. The PLL
multiplies this frequency by 150 to 4.9152MHz. This frequency is supplied to the ADC, the FIR filter (CKFIR), the clock test
output pin (CKTEST), the CE DRAM and the clock generator. The clock generator provides two clocks, one for the MPU
(CKMPU) and one for the CE (CKCE).
The MPU clock frequency is determined by the I/O RAM register MPU_DIV (0x2004[2:0]) and can be CE*2
-MPU_DIV Hz
where MPU_DIV varies from 0 to 7 (MPU_DIV is 0 on power-up). This makes the MPU clock scalable from 4.9152MHz down
to 38.4kHz.
The circuit also generates a 2x MPU clock for use by the emulator. This clock is not generated when the I/O RAM register
ECK_DIS (0x2005[5]) is asserted by the MPU.
I2C Interface (EEPROM)
A dedicated 2-pin serial interface implements an I2C driver that can be used to communicate with external EEPROM devices.
The interface can be multiplexed onto the DIO pins DIO4 (SCK) and DIO5 (SDA) by setting the I/O RAM register DIO_EEX
(0x2008[4]). The MPU communicates with the interface through two SFR registers: EEDATA (0x9E) and EECTRL (0x9F). If the
MPU wishes to write a byte of data to EEPROM, it places the data in EEDATA and then writes the ‘Transmit’ code to EECTRL.
The write to EECTRL initiates the transmit sequence. By observing the BUSY bit in EECTRL the MPU can determine when the
transmit operation is finished (i.e. when the BUSY bit transitions from 1 to 0). INT5 is also asserted when BUSY falls. The MPU
can then check the RX_ACK bit to see if the EEPROM acknowledged the transmission.
A byte is read by writing the ‘Receive’ command to EECTRL and waiting for BUSY to fall. Upon completion, the received data
will appear in EEDATA.
The serial transmit and receive clock is 78kHz during each transmission, and SCL is held in a high state until the next
transmission. The bits in EECTRL are shown in Table 56.
The EEPROM interface can also be operated by controlling the DIO4 and DIO5 pins directly. However, controlling DIO4 and
DIO5 directly is discouraged, because it may tie up the MPU to the point where it may become too busy to process
interrupts.
V3P3
V3P3 -
400mV
V3P3-10mV
VBIAS
0V
Battery or
reset
mode
Normal
operation,
WDT
enabled
WDT dis-
abled
V1
when
(V1 < VBIAS)
the battery is
enabled
相关PDF资料
PDF描述
71M6513H-IGT/F SPECIALTY ANALOG CIRCUIT, PQFP100
71M6513H-IGTR/F SPECIALTY ANALOG CIRCUIT, PQFP100
71M6513-IGT/F SPECIALTY ANALOG CIRCUIT, PQFP100
71M6515H-IGTW/F SPECIALTY ANALOG CIRCUIT, PQFP64
71M6515H-IGTWR/F SPECIALTY ANALOG CIRCUIT, PQFP64
相关代理商/技术参数
参数描述
71M6515H 制造商:TERIDIAN 制造商全称:TERIDIAN 功能描述:Energy Meter IC
71M6515H_11 制造商:TERIDIAN 制造商全称:TERIDIAN 功能描述:Up to 10ppmC precision ultra-stable voltage reference Digital temperature compensation
71M6515H-DB 功能描述:开发板和工具包 - 8051 71M6515H Demo Brd RoHS:否 制造商:Silicon Labs 产品:Development Kits 工具用于评估:C8051F960, Si7005 核心: 接口类型:USB 工作电源电压:
71M6515H-IGT 制造商:Maxim Integrated Products 功能描述:METERING FRONT END - Rail/Tube
71M6515H-IGT/F 功能描述:计量片上系统 - SoC Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel