参数资料
| 型号： | A4403GEUTR-T |
| 厂商： | Allegro Microsystems Inc |
| 文件页数： | 10/16页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK ADJ 3A 16QFN |
| 标准包装： | 1 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 可调至 0.8V |
| 输入电压： | 9 V ~ 46 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 450kHz ~ 2MHz |
| 电流 - 输出： | 3A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-WQFN 裸露焊盘 |
| 包装： | 标准包装 |
| 供应商设备封装： | 16-QFN（4x4） |
| 产品目录页面： | 1141 (CN2011-ZH PDF) |
| 其它名称： | 620-1273-6 |
A4403
Valley Current Mode Control Buck Converter
The amount of capacitance required for a given ripple voltage can
be found:
The sense resistor value is selected depending on the maximum
output load current. The typical sense voltage that causes a cur-
C IN =
I rms × T on
V RIPPLE
.
(15)
rent limit is 180 mV. So, for example, a 50 m Ω value would be
appropriate for a maximum load of 3 A, as it allows for margin
between maximum load and the current limit. A tolerance of up to
As mentioned in the previous section, E-field biasing effects
can reduce the actual capacitance and this should be taken into
account when making the selection.
Again, there is generally no need to consider the heating effects
of the RMS current flowing through the ESR of a ceramic
capacitor. If an electrolytic device is used, then the ripple current
rating should be considered. Note that most manufacturers only
consider the RMS current rating at 100 kHz.
Recirculation Diode This diode (D1) conducts during the
switch off-time. A Schottky diode is recommended to minimize
both the forward drop and switching losses. The worst-case
dissipation occurs at maximum V IN , when the duty cycle is at a
minimum.
The average current through the diode can be found:
I DIODE(av) = I LOAD × (1 – D (min)) . (16)
The forward voltage drop, V f , can be found from the diode
characteristics by using the actual load current (not the average
current).
The static power dissipation can be found:
±5% is acceptable.
The power rating of the resistor has to be considered. The current
flowing in the resistor is essentially the same as the current flow-
ing through the recirculation diode, although the power dissipa-
tion is worked out using the RMS current.
To a first approximation, the sense resistor dissipation can be
worked out as:
P SENSE = I LOAD2 × (1 – D (min)) × R SENSE . (18)
For a converter working with a load of 3 A, a very narrow duty
cycle, and a sense resistor of 50 m Ω , the power dissipation would
be 450 mW.
The optimal solution from a cost perspective is to use two
100 m Ω , 1206-style resistors connected in parallel. Each resistor
is generally rated at 250 mW at 70°C ambient. Check the vendor
datasheet to verify the maximum ambient at full power.
When laying out the PCB, it is essential that the sense resistor
connections, carrying the power current (see figure 3), are as
short and wide as possible to minimize the effects of leakage
inductance noise. In addition, the Kelvin sense circuit connec-
tions should be as close to the sense resistor pads as possible.
P STAT = I DIODE(av) × V f .
(17)
It is also important to take into account the thermal rating of
the package, R θ JA , and the ambient temperature, to ensure that
enough heatsinking is provided to maintain the diode junction
ISEN
Kelvin
connection
temperature within the safe operating area for the device.
To minimize the heating effects from the A4403 on the diode and
vice-versa, it is recommended that the diode be mounted on the
reverse side of the printed circuit board.
A4403
R FILTER
47 Ω
R SENSE
C FILTER
1 nF
Power
current
Sense Resistor The sense resistor should be a surface mount
package, with low inductance. On no account should a wire-
wound or through hole package be used. To prevent potential
mistriggering problems from occurring in noisy systems, it is
recommended that an R-C filter be applied across the sense resis-
tor, as shown in figure 3.
SGND
Kelvin
connection
Figure 3. R-C filter added to the current sense circuit
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
10
相关PDF资料 |
PDF描述 |
|---|---|
| A4447SLJTR-T | IC REG BUCK ADJ 2A 8SOIC |
| A4490EES-T | IC REG BUCK ADJ 1.5A TRPL 20QFN |
| A4491EESTR-T | IC REG BUCK ADJ 2.2A TRPL 20QFN |
| A4931MET-T | IC DC MOTOR PREDRIVER 3PH 28QFN |
| A4934GLPTR-T | IC BLDC DVR 3PHASE 16-ETSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| A4405 | 制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:The A4405 is an automotive power management IC that uses a high frequency constant on-time 5.45 V pre-regulator to supply two internal 5 V linear regulators and a 3.3 V linear DMOS driver. |
| A4405KLPTR-T | 制造商:Allegro MicroSystems LLC 功能描述:AUTOMOTIVE TRIPLE-OUTPUT REGULATOR |
| A4406 | 制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:The A4406 is an automotive power management IC that uses a high frequency constant on-time 5.45 V pre-regulator to supply an internal 5 V linear regulator and a 3.3 V linear DMOS driver. |
| A4406KLPTR-T | 功能描述:IC REG BUCK/LINEAR 16TSSOP 制造商:allegro microsystems, llc 系列:* 零件状态:在售 标准包装:4,000 |
| A4407 | 制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:The A4407 is an automotive power management IC that uses a 2.2 MHz constant on-time (COT) buck pre-regulator to supply a 5 V linear regulator, a 5 V tracking/protected linear regulator, |
发布紧急采购，3分钟左右您将得到回复。