参数资料
| 型号： | A4403GEUTR-T |
| 厂商： | Allegro Microsystems Inc |
| 文件页数： | 8/16页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK ADJ 3A 16QFN |
| 标准包装： | 1 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 可调至 0.8V |
| 输入电压： | 9 V ~ 46 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 450kHz ~ 2MHz |
| 电流 - 输出： | 3A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-WQFN 裸露焊盘 |
| 包装： | 标准包装 |
| 供应商设备封装： | 16-QFN（4x4） |
| 产品目录页面： | 1141 (CN2011-ZH PDF) |
| 其它名称： | 620-1273-6 |
A4403
Valley Current Mode Control Buck Converter
When the output voltage is set for 0.8 V, the typical bandwidth
is 90 kHz with a phase margin of 45° at full load. As the load is
reduced, the bandwidth remains largely constant; however, the
phase margin tends to reduce slightly because the output power
pole is shifted down in frequency, introducing the phase lag
sooner. At light loads, before pulse frequency modulation occurs,
the phase margin reduces to approximately 40°, which is reason-
able given that it is the worst-case condition. Note that when
pulse frequency modulation occurs, the system no longer operates
as a linear system, therefore, the control laws do not apply.
A good starting point in selecting the inductance for a given
application is to specify a maximum peak-to-peak ripple current
of about 25% of the maximum load. The equates to a ripple cur-
rent of approximately 750 mA for a maximum load of 3 A. This
often gives a good compromise between size, cost, and perfor-
mance.
The maximum peak to peak ripple current, I RIPP , occurs at the
maximum input voltage. Therefore the duty cycle, D, should be
found under these conditions:
When the output voltage is set for higher voltages, the DC gain
is reduced by the resistor feedback network from the output. This
D (min) =
V OUT +V f
V IN (max) +V f
,
(9)
effectively reduces the bandwidth of the control loop. An optional
speed-up capacitor (C6) can be used in parallel with the feedback
resistor (R5) to compensate for this effect. The addition of this
capacitor introduces an additional zero which increases the gain
where V f is the forward voltage drop of the recirculation diode
and the sense resistor.
The required inductance can be found:
and extends the bandwidth to maintain it in the region of 90 kHz.
The position of the zero depends on the values of R5 and C6.
The following time constants should be used for various output
L (min) =
V IN – V OUT
I RIPP
× D (min) ×
1
f SW (min)
. (10)
voltages:
Note that the manufacturers inductance tolerance should also be
taken into account. This value may be as high as ±20%.
Output Voltage
(V)
5
3.3
2.5
1.5
0.8
Time Constant
( τ)
3.6 × 10 –5
2.4 × 10 –5
1.8 × 10 –5
1.1 × 10 –5
Not required
In addition, because the control is dependant on the valley signal,
it is important to consider the minimum peak to peak valley
voltage that is developed across the sense resistor. The minimum
peak to peak ripple current occurs at minimum input voltage. The
peak to peak voltage is simply the peak to peak current multiplied
by the sense resistor value. It is recommended that the peak to
peak sense voltage should be greater than 25 mV.
For example, assume a target output voltage of 5 V, and an R5
of 3.92 k Ω to achieve that voltage. Then C6 = 9.18 × 10 –9 . The
nearest commonly available value is 10 nF.
For applications that require output voltages (V OUT ) other than
what is defined above, the following formula should be used to
calculate the time constant:
It is recommended that gapped ferrite solutions be used as
opposed to powdered iron solutions. The latter exhibit relatively
high core losses that can have a large impact on long term reli-
ability.
Inductors are typically specified at two current levels:
? RMS current. It is important to understand how the RMS cur-
τ = V OUT × 7.2 × 10 –6 ,
(8)
rent level is specified, in terms of ambient temperature. Some
manufacturers quote an ambient only, whilst others quote a tem-
Inductor The main factor in selecting the inductance value is
the ripple current. The ripple current affects the output voltage
ripple and also has an effect on the current limit. Because slope
compensation is not used, the ripple current is not constrained by
this factor.
perature that includes a self-temperature rise. For example, if an
inductor is rated for 85°C and includes a self-temperature rise of
25°C at maximum load, then the inductor cannot be safely oper-
ated beyond an ambient temperature of 60°C at full load. The
RMS current can be assumed to be simply the maximum load
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
8
相关PDF资料 |
PDF描述 |
|---|---|
| A4447SLJTR-T | IC REG BUCK ADJ 2A 8SOIC |
| A4490EES-T | IC REG BUCK ADJ 1.5A TRPL 20QFN |
| A4491EESTR-T | IC REG BUCK ADJ 2.2A TRPL 20QFN |
| A4931MET-T | IC DC MOTOR PREDRIVER 3PH 28QFN |
| A4934GLPTR-T | IC BLDC DVR 3PHASE 16-ETSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| A4405 | 制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:The A4405 is an automotive power management IC that uses a high frequency constant on-time 5.45 V pre-regulator to supply two internal 5 V linear regulators and a 3.3 V linear DMOS driver. |
| A4405KLPTR-T | 制造商:Allegro MicroSystems LLC 功能描述:AUTOMOTIVE TRIPLE-OUTPUT REGULATOR |
| A4406 | 制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:The A4406 is an automotive power management IC that uses a high frequency constant on-time 5.45 V pre-regulator to supply an internal 5 V linear regulator and a 3.3 V linear DMOS driver. |
| A4406KLPTR-T | 功能描述:IC REG BUCK/LINEAR 16TSSOP 制造商:allegro microsystems, llc 系列:* 零件状态:在售 标准包装:4,000 |
| A4407 | 制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:The A4407 is an automotive power management IC that uses a 2.2 MHz constant on-time (COT) buck pre-regulator to supply a 5 V linear regulator, a 5 V tracking/protected linear regulator, |
发布紧急采购，3分钟左右您将得到回复。