- 您现在的位置：买卖IC网 > PDF目录9287 > AD5263BRUZ50-REEL7 (Analog Devices Inc)IC POT DGTL 50K 256POS 24TSSOP PDF资料下载
参数资料
| 型号： | AD5263BRUZ50-REEL7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 14/28页 |
| 文件大小： | 0K |
| 描述： | IC POT DGTL 50K 256POS 24TSSOP |
| 标准包装： | 1,000 |
| 接片： | 256 |
| 电阻（欧姆）： | 50k |
| 电路数： | 4 |
| 温度系数： | 标准值 30 ppm/°C |
| 存储器类型： | 易失 |
| 接口： | I²C，SPI（芯片选择，设备位址） |
| 电源电压： | 2.7 V ~ 5.5 V，5 V ~ 15 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 24-TSSOP |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
Data Sheet
AD5263
Rev. F | Page 21 of 28
MULTIPLE DEVICES ON ONE BUS
Figure 49 shows four AD5263 devices on the same serial bus. Each
has a different slave address because the states of their AD0 and
AD1 pins are different. This allows each RDAC within each device
to be written to or read from independently. The master device
output bus line drivers are open-drain, pull-downs in a fully
I2C-compatible interface.
03142-
048
MASTER
AD5263
R P
+5V
SDA
SCL
AD0
5V
AD1
SDA SCL
AD5263
AD0
AD1
SDA SCL
AD5263
AD0
AD1
SDA SCL
AD5263
AD0
AD1
SDA SCL
LEVEL SHIFT FOR NEGATIVE VOLTAGE OPERATION
The digital potentiometer is popular in laser diode driver and
certain telecommunication equipment level-setting applications.
These applications are sometimes operated between ground and
some negative supply voltage so that the systems can be biased
at round to avoid large bypass capacitors that may significantly
impede the ac performance. Like most digital potentiometers, the
AD5263 can be configured with a negative supply (see Figure 50).
03142-
050
SDA
GND
VSS
VDD
SCL
LEVEL SHIFTED
–5V
AD5263
Figure 50. Biased at Negative Voltage
However, the digital inputs must also be level shifted to allow
proper operation because the ground is referenced to the negative
potential. As a result, Figure 51 shows one implementtation
with a couple of transistors and a few resistors. When VIN is
high, Q1 is turned on and its emitter is clamped at one threshold
above ground. This threshold appears at the base of Q2, which
causes Q2 to turn off. In this state, VOUT approaches 5 V. When
VIN is low, Q1 is turned off and the base of Q2 is pulled low, which
in turn causes Q2 to turn on. In this state, VOUT approaches 0 V.
Beware that proper time shifting is also needed for successful
communication with the device.
03142-
051
VIN
VOUT
–5V
Q2
2N3906
Q1
2N3906
+5V
0V
–5V
0V
R3
1k
R1
10k
R2
10k
Figure 51. Level Shift for Bipolar Potential Operation
ESD PROTECTION
All digital inputs are protected with a series input resistor and
parallel Zener ESD structures shown in Figure 52 and Figure 53.
This protection applies to digital input pins SDI/SDA, CLK/SCL,
CS/AD0, RES/AD1, and SHDN.
LOGIC
340
VSS
03142-
052
Figure 52. ESD Protection of Digital Pins
03142-
053
A,B,W
VSS
Figure 53. ESD Protection of Resistor Terminals
TERMINAL VOLTAGE OPERATING RANGE
the boundary conditions for proper 3-terminal digital
potentiometer operation. Supply signals present on the A, B,
and W terminals that exceed VDD or VSS are clamped by the
internal forward-biased diodes shown in Figure 54.
A
VDD
B
W
VSS
03142-
054
Figure 54. Maximum Terminal Voltages Set by VDD and VSS
POWER-UP SEQUENCE
Because the ESD protection diodes limit the voltage compliance
at the A, B, and W terminals (see Figure 54), it is important to
power VDD and VSS before applying any voltage to the A, B, and
W terminals; otherwise, the diodes are forward biased such that
VDD and VSS are powered unintentionally and may affect the rest
of the circuit. The ideal power-up sequence is in the following
order: GND, VDD, VSS, VL, digital inputs, and VA/B/W. The relative
order of powering VA, VB, VW, and digital inputs is not important as
long as they are powered after VDD and VSS.
相关PDF资料 |
PDF描述 |
|---|---|
| DS1100Z-50+ | IC DELAY LINE 5TAP 50NS 8-SOIC |
| VE-272-MX-B1 | CONVERTER MOD DC/DC 15V 75W |
| MS27484T16A42PA | CONN PLUG 42POS STRAIGHT W/PINS |
| VI-B6H-IU-F4 | CONVERTER MOD DC/DC 52V 200W |
| VI-B4Z-MX-F4 | CONVERTER MOD DC/DC 2V 30W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD5263EVAL | 制造商:Analog Devices 功能描述:Evaluation Board For Digital Potentiometer, Quad, 15V, 256-Position, Digital Potentiometer 制造商:Analog Devices 功能描述:AD5263 EVAL BOARD - Bulk |
| AD52651A | 制造商:ESMT 制造商全称:Elite Semiconductor Memory Technology Inc. 功能描述:2.5W/CH Stereo Filter-less Class-D Audio Amplifier with Headphone Driver |
| AD5266 | 制造商:ESMT 制造商全称:Elite Semiconductor Memory Technology Inc. 功能描述:16V STEREO CLASS-D AUDIO POWER AMPLIFIER with STEREO HEADPHONE |
| AD526A | 制造商:AD 制造商全称:Analog Devices 功能描述:Software Programmable Gain Amplifier |
| AD526AD | 功能描述:IC AMP PGA 10MA 16CDIP RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:2,500 系列:Excalibur™ 放大器类型:J-FET 电路数:1 输出类型:- 转换速率:45 V/µs 增益带宽积:10MHz -3db带宽:- 电流 - 输入偏压:20pA 电压 - 输入偏移:490µV 电流 - 电源:1.7mA 电流 - 输出 / 通道:48mA 电压 - 电源，单路/双路(±):4.5 V ~ 38 V，±2.25 V ~ 19 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SOIC 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。