参数资料
| 型号： | AD5372BSTZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 10/29页 |
| 文件大小： | 0K |
| 描述： | IC DAC 16BIT 32CH SER 64-LQFP |
| 产品培训模块： | Data Converter Fundamentals DAC Architectures |
| 标准包装： | 1 |
| 设置时间： | 20µs |
| 位数： | 16 |
| 数据接口： | 串行 |
| 转换器数目： | 32 |
| 电压电源： | 双 ± |
| 功率耗散（最大）： | 520mW |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 64-LQFP |
| 供应商设备封装： | 64-LQFP（10x10） |
| 包装： | 托盘 |
| 输出数目和类型： | 32 电压，单极；32 电压，双极 |
| 采样率（每秒）： | * |
| 产品目录页面： | 782 (CN2011-ZH PDF) |
| 配用： | EVAL-AD5372EBZ-ND - BOARD EVAL FOR AD5372 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页
AD5372/AD5373
Rev. C | Page 17 of 28
OUTPUT AMPLIFIER
Because the output amplifiers can swing to 1.4 V below the
positive supply and 1.4 V above the negative supply, this limits
how much the output can be offset for a given reference voltage.
For example, it is not possible to have a unipolar output range
of 20 V, because the maximum supply voltage is ±16.5 V.
05
81
5-
02
0
CLR
DAC
CHANNEL
OFFSET
DAC
OUTPUT
R6
10k
R2
20k
S3
S2
S1
R4
60k
R3
20k
SIGGNDx
R5
60k
R1
20k
Figure 21. Output Amplifier and Offset DAC
Figure 21 shows details of a DAC output amplifier and its
connections to the offset DAC. On power-up, S1 is open,
disconnecting the amplifier from the output. S3 is closed, so
the output is pulled to SIGGNDx (R1 and R2 are greater than
R6). S2 is also closed to prevent the output amplifier from being
open-loop. If CLR is low at power-up, the output remains in this
condition until CLR is taken high. The DAC registers can be
programmed, and the outputs assume the programmed values
when CLR is taken high. Even if CLR is high at power-up, the
output remains in the previous condition until VDD > 6 V and
VSS < 4 V and the initialization sequence has finished. The
outputs then go to their power-on default value.
TRANSFER FUNCTION
The output voltage of a DAC in the AD5372/AD5373 is depend-
ent on the value in the input register, the value of the M and C
registers, and the value in the offset DAC.
AD5372 Transfer Function
The input code is the value in the X1A or X1B register that is
applied to the DAC (X1A, X1B default code = 21,844).
DAC_CODE = INPUT_CODE × (M + 1)/216 + C 215
where:
M = code in gain register default code = 216 – 1.
C = code in offset register default code = 215.
The DAC output voltage is calculated as follows:
VOUT = 4 × VREFx × (DAC_CODE – (OFFSET_CODE ×
4))/216 + VSIGGND
where:
DAC_CODE should be within the range of 0 to 65,535.
For 12 V span, VREFx = 3.0 V.
For 20 V span, VREFx = 5.0 V.
OFFSET_CODE is the code loaded to the offset DAC. It is
multiplied by 4 in the transfer function because this DAC is
a 14-bit device. On power-up, the default code loaded to the
offset DAC is 5461 (0x1555). With a 3 V reference, this gives
a span of 4 V to +8 V.
AD5373 Transfer Function
The input code is the value in the X1A or X1B register that is
applied to the DAC (X1A, X1B default code = 5461).
DAC_CODE = INPUT_CODE × (M + 1)/214 + C 213
where:
M = code in gain register default code = 214 – 1.
C = code in offset register default code = 213.
The DAC output voltage is calculated as follows:
VOUT = 4 × VREFx × (DAC_CODE –
OFFSET_CODE)/214 + VSIGGND
where:
DAC_CODE should be within the range of 0 to 16,383.
For 12 V span, VREFx = 3.0 V.
For 20 V span, VREFx = 5.0 V.
OFFSET_CODE is the code loaded to the offset DAC.
On power-up, the default code loaded to the offset DAC
is 5461 (0x1555). With a 3 V reference, this gives a span
of 4 V to +8 V.
REFERENCE SELECTION
The AD5372/AD5373 have two reference input pins. The
voltage applied to the reference pins determines the output
voltage span on VOUT0 to VOUT31. VREF0 determines the
voltage span for VOUT0 to VOUT7 (Group 0), and VREF1
determines the voltage span for VOUT8 to VOUT31 (Group 1
to Group 3). The reference voltage applied to each VREF pin
can be different, if required, allowing the groups to have
different voltage spans. The output voltage range and span
can be adjusted further by programming the offset and gain
registers for each channel as well as programming the offset
DACs. If the offset and gain features are not used (that is, the
M and C registers are left at their default values), the required
reference levels can be calculated as follows:
VREF = (VOUTMAX – VOUTMIN)/4
If the offset and gain features of the AD5372/AD5373 are used,
the required output range is slightly different. The selected
output range should take into account the system offset and
gain errors that need to be trimmed out. Therefore, the selected
output range should be larger than the actual required range.
相关PDF资料 |
PDF描述 |
|---|---|
| LTC1595AIS8#PBF | IC D/A CONV 16BIT MULTPLYNG8SOIC |
| VE-2TJ-MY-F3 | CONVERTER MOD DC/DC 36V 50W |
| VI-B4Z-MU-F4 | CONVERTER MOD DC/DC 2V 80W |
| LTC2757BILX#PBF | IC DAC 18BIT PAR 48LQFP |
| MS3114E22-41SY | CONN RCPT 41POS JAM NUT W/SCKT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD5372BSTZ-REEL | 功能描述:IC DAC 16BIT 32CH SER 64-LQFP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1,000 系列:- 设置时间:1µs 位数:8 数据接口:串行 转换器数目:8 电压电源:双 ± 功率耗散（最大）:941mW 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC W 包装:带卷 (TR) 输出数目和类型:8 电压，单极 采样率（每秒）:* |
| AD5373BCPZ | 功能描述:数模转换器- DAC 32-CH 14-bit Serial bipolar DAC I.C. RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| AD5373BCPZ-RL7 | 功能描述:14 Bit Digital to Analog Converter 32 56-LFCSP-VQ (8x8) 制造商:analog devices inc. 系列:- 包装:带卷（TR） 零件状态:上次购买时间 位数:14 数模转换器数:32 建立时间:30μs 输出类型:Voltage - Buffered 差分输出:无 数据接口:SPI，DSP 参考类型:外部 电压 - 电源，模拟:9 V ~ 16.5 V，-4.5 V ~ 16.5 V 电压 - 电源，数字:2.5 V ~ 5.5 V INL/DNL（LSB）:±1（最大），±1（最大） 架构:电阻串 DAC 工作温度:-40°C ~ 85°C 封装/外壳:56-VFQFN 裸露焊盘，CSP 供应商器件封装:56-LFCSP-VQ（8x8） 标准包装:1 |
| AD5373BSTZ | 功能描述:IC DAC 14BIT 32CH SER 64-LQFP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1,000 系列:- 设置时间:1µs 位数:8 数据接口:串行 转换器数目:8 电压电源:双 ± 功率耗散（最大）:941mW 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC W 包装:带卷 (TR) 输出数目和类型:8 电压，单极 采样率（每秒）:* |
| AD5373BSTZ-REEL | 功能描述:IC DAC 14BIT 32CH SER 64-LQFP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1,000 系列:- 设置时间:1µs 位数:8 数据接口:串行 转换器数目:8 电压电源:双 ± 功率耗散（最大）:941mW 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC W 包装:带卷 (TR) 输出数目和类型:8 电压，单极 采样率（每秒）:* |
发布紧急采购，3分钟左右您将得到回复。