- 您现在的位置：买卖IC网 > PDF目录10791 > AD5384BBC-3 (Analog Devices Inc)IC DAC 14BIT 40CH 3V 100-CSPBGA PDF资料下载
参数资料
| 型号： | AD5384BBC-3 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 14/32页 |
| 文件大小： | 0K |
| 描述： | IC DAC 14BIT 40CH 3V 100-CSPBGA |
| 产品培训模块： | Data Converter Fundamentals DAC Architectures |
| 产品变化通告： | AD5384 Models Discontinuation 15/May/2012 |
| 标准包装： | 1 |
| 设置时间： | 8µs |
| 位数： | 14 |
| 数据接口： | 串行 |
| 转换器数目： | 40 |
| 电压电源： | 单电源 |
| 功率耗散（最大）： | 80mW |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 100-LFBGA，CSPBGA |
| 供应商设备封装： | 100-CSBGA（10x10） |
| 包装： | 托盘 |
| 输出数目和类型： | 40 电压，单极 |
| 采样率（每秒）： | 125k |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
Data Sheet
AD5384
Table 12. Control Register Contents
MSB
LSB
CR13
CR12
CR11
CR10
CR9
CR8
CR7
CR6
CR5
CR4
CR3
CR2
CR1
CR0
Control Register Write/Read
REG1 = REG0 = 0, A5 to A0 = 001100, and R/W status
determines if the operation is a write (R/W = 0) or a read (R/W
= 1). The DB13 to DB0 bits contain the control register data.
Control Register Contents
CR13: power-down status. This bit configures the output
amplifier state in power-down mode This bit is configured as
follows:
For CR13 = 1, the amplifier output is high impedance
(default at power-up).
For CR13 = 0, the amplifier output is 100 k to ground.
CR12: REF select. This bit selects the operating internal
reference for the AD5384. CR12 is programmed as follows:
For CR12 = 1, the internal reference is 2.5 V, which is the
recommended operating reference.
For CR12 = 0, the internal reference is 1.25 V.
CR11: current boost control. This bit boosts the current in the
output amplifier, thereby altering its slew rate. This bit is
configured as follows:
For CR11 = 1, boost mode is on, maximizing the bias
current in the output amplifier, and optimizing its slew
rate but increasing the power dissipation.
For CR11 = 0, boost mode is off (default at power-up),
reducing the bias current in the output amplifier and the
overall power consumption.
CR10: internal/external reference. This bit determines if the
DAC uses its internal reference or an externally applied
reference. This bit is configured as follows:
For CR10 = 1, the internal reference is enabled. The
reference output depends on data loaded to CR12.
For CR10 = 0, the external reference is selected (default
at power-up).
CR9: channel monitor enable (see Channel Monitor Function).
This bit is configured as follows:
For CR9 = 1, the monitor is enabled which enables the
channel monitor function. After a write to the monitor
channel in the SFR register, the selected channel output
routes to the MON_OUT pin. VOUT39 operates as the
MON_OUT pin.
For CR9 = 0, the monitor is disabled (default at power-
up). When the monitor is disabled, the MON_OUT pin
assumes its normal DAC output function.
CR8: thermal monitor function. This function monitors the
AD5384 internal die temperature, when enabled. The thermal
monitor powers down the output amplifiers when the
temperature exceeds 130°C. This function protects the device
when power dissipation is exceeded, if a number of output
channels are simultaneously short circuited. If the die
temperature drops below 130°C, a soft power-up reenables the
output amplifiers. This bit is configured as follows:
For CR8 = 1, the thermal monitor is enabled.
For CR8 = 0, the thermal monitor is disabled (default at
power-up).
CR7: don’t care.
CR6 to CR2: toggle function enable. This function toggles the
output between two codes loaded to the A and B register for
each DAC. Control Register Bit CR6 to Control Register Bit
CR2 enable individual groups of eight channels for operation in
toggle mode. A Logic 1, written to any bit, enables a group of
channels, and a Logic 0 disables a group. LDAC is used to toggle
between the two registers. Table 13 shows the decoding for
toggle mode operation. For example, CR6 controls group w,
which contains Channel 32 to Channel 39, CR6 = 1 enables
these channels.
CR1 and CR0: don’t care.
Table 13. Toggle Function Enable
CR Bit
Group
Channels
CR6
4
32 to 39
CR5
3
24 to 31
CR4
2
16 to 23
CR3
1
8 to 15
CR2
0
0 to 7
Channel Monitor Function
REG1 = REG0 = 0, A5 to A0 = 001010, and DB13 to DB8 =
contain data to address the monitored channel.
The AD5384 has a channel monitor function that consists of a
multiplexer address via the interface, allows any channel output
to be routed to the MON_OUT pin for monitoring, using an
external ADC. In channel monitor mode, VOUT39 becomes
the MON_OUT pin, to which all monitored pins are routed.
Enable the channel monitor function in the control register
before any channels are routed to the MON_OUT pin. On the
AD5384, DB13 to DB8 contain the channel address for the
monitored channel. Selecting Channel Address 63 three-states
the MON_OUT pin.
Rev. B | Page 21 of 32
相关PDF资料 |
PDF描述 |
|---|---|
| AD5384BBC-3REEL7 | IC DAC 14BIT 40CH 3V 100-CSPBGA |
| ADCMP572BCPZ-R2 | IC COMPARATOR CML 3.3-5V 16LFCSP |
| LTC1687IS#PBF | IC TXRX RS485 PREC DELAY 14-SOIC |
| LTC1686IS8#PBF | IC TXRX RS485 PREC DELAY 8-SOIC |
| AD96687BQ | IC COMP DUAL 2.5NS 16-CDIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD5384BBC-3REEL7 | 功能描述:IC DAC 14BIT 40CH 3V 100-CSPBGA RoHS:否 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 标准包装:2,400 系列:- 设置时间:- 位数:18 数据接口:串行 转换器数目:3 电压电源:模拟和数字 功率耗散（最大）:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:36-TFBGA 供应商设备封装:36-TFBGA 包装:带卷 (TR) 输出数目和类型:* 采样率（每秒）:* |
| AD5384BBC-5 | 功能描述:IC DAC 14BIT 40CH 5V 100-CSPBGA RoHS:否 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 标准包装:2,400 系列:- 设置时间:- 位数:18 数据接口:串行 转换器数目:3 电压电源:模拟和数字 功率耗散（最大）:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:36-TFBGA 供应商设备封装:36-TFBGA 包装:带卷 (TR) 输出数目和类型:* 采样率（每秒）:* |
| AD5384BBC-5REEL7 | 功能描述:IC DAC 14BIT 40CH 5V 100-CSPBGA RoHS:否 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 标准包装:2,400 系列:- 设置时间:- 位数:18 数据接口:串行 转换器数目:3 电压电源:模拟和数字 功率耗散（最大）:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:36-TFBGA 供应商设备封装:36-TFBGA 包装:带卷 (TR) 输出数目和类型:* 采样率（每秒）:* |
| AD5384BBCZ-3 | 功能描述:IC DAC 14BIT 40CH 5V 100-CSPBGA RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 标准包装:2,400 系列:- 设置时间:- 位数:18 数据接口:串行 转换器数目:3 电压电源:模拟和数字 功率耗散（最大）:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:36-TFBGA 供应商设备封装:36-TFBGA 包装:带卷 (TR) 输出数目和类型:* 采样率（每秒）:* |
| AD5384BBCZ-5 | 功能描述:IC DAC 14BIT 40CH 5V 100-CSPBGA RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 标准包装:2,400 系列:- 设置时间:- 位数:18 数据接口:串行 转换器数目:3 电压电源:模拟和数字 功率耗散（最大）:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:36-TFBGA 供应商设备封装:36-TFBGA 包装:带卷 (TR) 输出数目和类型:* 采样率（每秒）:* |
发布紧急采购，3分钟左右您将得到回复。