- 您现在的位置：买卖IC网 > PDF目录373897 > AD73422BB-80 (ANALOG DEVICES INC) Dual Low Power CMOS Analog Front End with DSP Microcomputer PDF资料下载
参数资料
| 型号： | AD73422BB-80 |
| 厂商： | ANALOG DEVICES INC |
| 元件分类： | 数字信号处理 |
| 英文描述： | Dual Low Power CMOS Analog Front End with DSP Microcomputer |
| 中文描述： | 24-BIT, 52 MHz, MIXED DSP, PBGA119 |
| 封装： | PLASTIC, BGA-119 |
| 文件页数： | 36/36页 |
| 文件大小： | 396K |
| 代理商： | AD73422BB-80 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页当前第36页
REV. 0
AD73422
–
36
–
Grounding and Layout
As the analog inputs to the AD73422’s AFE section are differ-
ential, most of the voltages in the analog modulator are common-
mode voltages. The excellent common-mode rejection of the
part will remove common-mode noise on these inputs. The
analog and digital supplies of the AD73422 are independent and
separately pinned out to minimize coupling between analog and
digital sections of the device. The digital filters on the encoder
section will provide rejection of broadband noise on the power
supplies, except at integer multiples of the modulator sampling
frequency. The digital filters also remove noise from the analog
inputs provided the noise source does not saturate the analog
modulator. However, because the resolution of the AD73422’s
ADC is high, and the noise levels from the AD73422 are so low,
care must be taken with regard to grounding and layout.
The printed circuit board that houses the AD73422 should be
designed so the analog and digital sections are separated and
confined to certain sections of the board. The AD73422 ball-
out configuration offers a major advantage in that its analog
interfaces are confined to the last three rows of the package.
This facilitates the use of ground planes that can be easily sepa-
rated, as shown in Figure 35. A minimum etch technique is
generally best for ground planes as it gives the best shielding.
Digital and analog ground planes should be joined in only one
place. If this connection is close to the device, it is recommended
to use a ferrite bead inductor.
Avoid running digital lines under the AFE section of the device
for they will couple noise onto the die. The analog ground plane
should be allowed to run under the AD73422’s AFE section to
avoid noise coupling (see Figure 35). The power supply lines to
the AD73422 should use as large a trace as possible to provide
low impedance paths and reduce the effects of glitches on the
power supply lines. Fast switching signals such as clocks should
be shielded with digital ground to avoid radiating noise to other
sections of the board, and clock signals should never be run near
ANALOG
GROUND PLANE
DIGITAL
GROUND PLANE
AFE ANALOG
AFE DIGITAL
DSP
A B C D E F G H J K L M N P R T U
7
6
5
4
3
2
1
Figure 35. Ground Plane Layout
the analog inputs. Traces on opposite sides of the board should
run at right angles to each other. This will reduce the effects of
feedthrough through the board. A microstrip technique is by far
the best but is not always possible with a double-sided board. In
this technique, the component side of the board is dedicated to
ground planes while signals are placed on the other side.
Good decoupling is important when using high speed devices.
On the AD73422 both the reference (REFCAP) and supplies
need to be decoupled. It is recommended that the decoupling
capacitors used on both REFCAP and the supplies, be placed as
close as possible to their respective ball connections to ensure
high performance from the device. All analog and digital sup-
plies should be decoupled to AGND and DGND respectively,
with 0.1
μ
F ceramic capacitors in parallel with 10
μ
F tantalum
capacitors. The AFE’s digital section supply (DVDD) should be
connected to the digital supply that feeds the DSP’s VDD(Ext)
connections while the AFE’s digital ground DGND should be
returned to the digital ground plane.
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
119-Ball Plastic Ball Grid Array (PBGA)
B-119
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
T
U
7 6 5 4 3 2 1
0.050
(1.27)
BSC
0.800
(20.32)
BSC
0.300 (7.62) BSC
0.050 (1.27)
BSC
0.126 (3.19)
REF
0.033
(0.84)
REF
BOTTOM
VIEW
A1
TOP VIEW
0.874 (22.20)
0.858 (21.80)
0.559 (14.20)
0.543 (13.80)
0.089 (2.27)
0.073 (1.85)
DETAIL A
SEATING
PLANE
0.037 (0.95)
0.033 (0.85)
0.028 (0.70)
0.020 (0.50)
DETAIL A
0.035 (0.90)
0.024 (0.60)
BALL DIAMETER
0.022 (0.56)
REF
P
C
–
8
–
6
相关PDF资料 |
PDF描述 |
|---|---|
| AD73422 | Dual Low Power CMOS Analog Front End with DSP Microcomputer(带DSP微计算机的双模拟前端) |
| AD73422BB-40 | Dual Low Power CMOS Analog Front End with DSP Microcomputer |
| AD73460BB-80 | Six-Input Channel Analog Front End |
| AD73460 | Six-Input Channel Analog Front End |
| AD73460BB-40 | Six-Input Channel Analog Front End |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD73422BBZ-40 | 制造商:Analog Devices 功能描述:AUD CODEC 2ADC / 2DAC 16BIT 119BGA - Bulk |
| AD7342AST-REEL | 制造商:Rochester Electronics LLC 功能描述:- Tape and Reel 制造商:Analog Devices 功能描述: |
| AD7343AST-REEL | 制造商:Analog Devices 功能描述: |
| ad7343asu-reel | 制造商:Rochester Electronics LLC 功能描述:- Tape and Reel 制造商:Analog Devices 功能描述: |
| AD7344ASTZ | 制造商:Analog Devices 功能描述: |
发布紧急采购，3分钟左右您将得到回复。