- 您现在的位置：买卖IC网 > PDF目录10541 > AD7854LARSZ (Analog Devices Inc)IC ADC 12BIT PARALLEL LP 28SSOP PDF资料下载
参数资料
| 型号： | AD7854LARSZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 9/28页 |
| 文件大小： | 0K |
| 描述： | IC ADC 12BIT PARALLEL LP 28SSOP |
| 标准包装： | 47 |
| 位数： | 12 |
| 采样率（每秒）： | 100k |
| 数据接口： | 并联 |
| 转换器数目： | 2 |
| 功率耗散（最大）： | 30mW |
| 电压电源： | 模拟和数字 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SSOP（0.209"，5.30mm 宽） |
| 供应商设备封装： | 28-SSOP |
| 包装： | 管件 |
| 输入数目和类型： | 1 个伪差分，单极；1 个伪差分，双极 |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
AD7854/AD7854L
REV. B
–17–
POWER-UP TIMES
Using an External Reference
When the AD7854/AD7854L are powered up, the parts are
powered up from one of two conditions. First, when the power
supplies are initially powered up and, secondly, when the parts
are powered up from a software power-down (see last section).
When AVDD and DVDD are powered up, the AD7854/AD7854L
enters a mode whereby the
CONVST signal initiates a timeout
followed by a self-calibration. The total time taken for this time-
out and calibration is approximately 70 ms—see Calibration on
Power-Up in the calibration section of this data sheet. The power-
up calibration mode can be disabled if the user writes to the control
register before a
CONVST signal is applied. If the timeout and
self-calibration are disabled, then the user must take into account
the time required by the AD7854/AD7854L to power up before
a self-calibration is carried out. This power-up time is the time
taken for the AD7854/AD7854L to power up when power is
first applied (300
s typ) or the time it takes the external refer-
ence to settle to the 12-bit level—whichever is the longer.
The AD7854/AD7854L powers up from a full software power-
down in 5
s typ. This limits the throughput which the part is
capable of to 100 kSPS for the AD7854 and 60 kSPS for the
AD7854L when powering down between conversions. Figure 21
shows how a full power-down between conversions is implemented
using the
CONVST pin. The user first selects the power-down
between conversions option by setting the power management
bits, PMGT1 and PMGT0, to 0 and 1 respectively in the control
register (see last section). In this mode the AD7854/AD7854L
automatically enters a full power-down at the end of a conver-
sion, i.e., when BUSY goes low. The falling edge of the next
CONVST pulse causes the part to power up. Assuming the
external reference is left powered up, the AD7854/AD7854L
should be ready for normal operation 5
s after this falling edge.
The rising edge of
CONVST initiates a conversion so the
CONVST pulse should be at least 5
s wide. The part auto-
matically powers down on completion of the conversion. Where
the software convert start is used, the part may be powered up in
software before a conversion is initiated.
tCONVERT
5 s
4.6 s
POWER-UP
TIME
NORMAL
OPERATION
FULL
POWER-DOWN
POWER-UP
TIME
POWER-UP ON FALLING EDGE
START CONVERSION ON RISING EDGE
BUSY
CONVST
Figure 21. Using the
CONVST Pin to Power Up the AD7854
for a Conversion
INPUT FREQUENCY – kHz
–78
–80
–90
0
100
20
PSRR
–
dB
40
60
–82
–84
–86
–88
80
AVDD = DVDD = 3.3V/5.0V,
100mV pk-pk SINE WAVE ON AVDD
3.3V
5.0V
Figure 20. PSRR vs. Frequency
POWER-DOWN OPTIONS
The AD7854/AD7854L provides flexible power management to
allow the user to achieve the best power performance for a given
throughput rate. The power management options are selected
by programming the power management bits, PMGT1 and
PMGT0, in the control register. Table VI summarizes the power-
down options that are available and how they can be selected by
programming the power management bits in the control register.
The AD7854/AD7854L can be fully or partially powered down.
When fully powered down, all the on-chip circuitry is powered
down and IDD is 10
A typ. If a partial power-down is selected,
then all the on-chip circuitry except the reference is powered
down and IDD is 400
A typ with the external clock running.
Additional power savings may be made if the external clock is off.
The choice of full or partial power-down does not give any
significant improvement in the throughput rate which can be
achieved with a power-down between conversions. This is dis-
cussed in the next section—Power-Up Times. But a partial
power-down does allow the on-chip reference to be used exter-
nally even though the rest of the AD7854/AD7854L circuitry is
powered down. It also allows the AD7854/AD7854L to be pow-
ered up faster after a long power-down period when using the
on-chip reference (See Power-Up Times section—Using the
Internal (On-Chip) Reference).
As can be seen from Table VI, the AD7854/AD7854L can be
programmed for normal operation, a full power-down at the end
of a conversion, a partial power-down at the end of a conversion
and finally a full power-down whether converting or not. The
full and partial power-down at the end of a conversion can be
used to achieve a superior power performance at slower through-
put rates, in the order of 50 kSPS (see Power vs. Throughput Rate
section of this data sheet).
Table VI. Power Management Options
PMGT1 PMGT0
Bit
Comment
0
Normal Operation
0
1
Full Power-Down After a Conversion
1
0
Full Power-Down
1
Partial Power-Down After a Conversion
相关PDF资料 |
PDF描述 |
|---|---|
| VI-J14-MY-F4 | CONVERTER MOD DC/DC 48V 50W |
| VI-J13-MY-F4 | CONVERTER MOD DC/DC 24V 50W |
| AD7495BRMZ | IC ADC 12BIT SRL LP W/REF 8MSOP |
| AD7495BRZ | IC ADC 12BIT SRL LP W/REF 8-SOIC |
| UTS7124S | CONN RCPT 4X1.6 FEMALE JAM NUT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7854LARSZ-REEL | 功能描述:IC ADC 12BIT PARALLEL LP 28SSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| AD7854LARZ | 功能描述:IC ADC 12BIT PARALLEL LP 28-SOIC RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 其它有关文件:TSA1204 View All Specifications 标准包装:1 系列:- 位数:12 采样率（每秒）:20M 数据接口:并联 转换器数目:2 功率耗散（最大）:155mW 电压电源:模拟和数字 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-TQFP 供应商设备封装:48-TQFP（7x7） 包装:Digi-Reel® 输入数目和类型:4 个单端，单极；2 个差分，单极 产品目录页面:1156 (CN2011-ZH PDF) 其它名称:497-5435-6 |
| AD7854LARZ-REEL | 功能描述:IC ADC 12BIT PARALLEL LP 28SOIC RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| AD7854LBR | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog-to-Digital Converter， 12-Bit |
| AD7854SQ | 制造商:Rochester Electronics LLC 功能描述:12-BIT SINGLE CH.PARALLEL ADC I.C. - Bulk |
发布紧急采购，3分钟左右您将得到回复。