- 您现在的位置：买卖IC网 > PDF目录1985 > AD7949BCPZRL7 (Analog Devices Inc)IC ADC 14BIT 250KSPS 8CH 20LFCSP PDF资料下载
参数资料
| 型号： | AD7949BCPZRL7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 19/32页 |
| 文件大小： | 0K |
| 描述： | IC ADC 14BIT 250KSPS 8CH 20LFCSP |
| 产品培训模块： | Power Line Monitoring |
| 产品变化通告： | Startup Circuitry Design Improvement Change 15/April/2009 |
| 标准包装： | 1,500 |
| 系列： | PulSAR® |
| 位数： | 14 |
| 采样率（每秒）： | 250k |
| 数据接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 15.5mW |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-VFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 20-LFCSP-VQ |
| 包装： | 带卷 (TR) |
| 输入数目和类型： | * |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
AD7949
Data Sheet
Rev. D | Page 26 of 32
GENERAL TIMING WITH A BUSY INDICATOR
Figure 37 details the timing for all three modes: read/write
during conversion (RDC), read/write after conversion (RAC),
and read/write spanning conversion (RSC). Note that the gating
item for both CFG and data readback is at the end of conversion
(EOC). As detailed previously, the data access should occur up
to safe data reading/writing time, tDATA. If the full CFG word is
not written to prior to EOC, it is discarded and the current
configuration remains.
At the EOC, if CNV is low, the busy indicator is enabled. In
addition, to generate the busy indicator properly, the host must
assert a minimum of 15 SCK falling edges to return SDO to
high impedance because the last bit on SDO remains active.
Unlike the case detailed in the General Timing Without a Busy
Indicator section, if the conversion result is not read out fully
prior to EOC, the last bit clocked out remains. If this bit is low,
the busy signal indicator cannot be generated because the busy
generation requires either a high impedance or a remaining bit
high-to-low transition. Because most SPI hosts are usually
limited to 8-bit or 16-bit bursts, this should not be an issue.
Additional clocks are not a concern because SDO remains high
impedance after the 15th falling edge.
The SCK can idle high or low depending on the CPOL and
CPHA settings if SPI is used. A simple solution is to use CPOL
= CPHA = 1 (not shown) with SCK idling high.
From power-up, in any read/write mode, the first three conver-
sion results are undefined because a valid CFG does not take
place until the 2nd EOC; thus, two dummy conversions are
required. Also, if the state machine writes the CFG during the
power-up state (RDC shown), the CFG register needs to be
rewritten again at the next phase. Note that the first valid data
occurs in Phase (n + 1) when the CFG register is written during
Phase (n 1).
ACQUISITION
(n – 1) UNDEFINED
ACQUISITION
(n)
ACQUISITION
(n + 1)
ACQUISITION
(n + 2)
PHASE
POWER
UP
EOC
START OF CONVERSION
(SOC)
EOC
CONVERSION
(n)
CONVERSION
(n + 1)
CONVERSION
(n – 2) UNDEFINED
tCONV
tCYC
tDATA
CNV
DIN
RDC
RAC
RSC
SDO
NOTES
1. CNV MUST BE LOW PRIOR TO THE END OF CONVERSION (EOC) TO GENERATE THE BUSY INDICATOR.
2. A TOTAL OF 15 SCK FALLING EDGES ARE REQUIRED TO RETURN SDO TO HIGH-Z. IF CFG READBACK IS ENABLED,
A TOTAL OF 29 SCK FALLING EDGES IS REQUIRED TO RETURN SDO TO HIGH-Z.
DATA (n)
DATA (n – 2)
XXX
DATA (n – 2)
XXX
DATA (n – 1)
XXX
DATA (n – 1)
XXX
DIN
SDO
DATA (n + 1)
DATA (n)
DATA (n + 1)
DIN
CFG (n)
CFG (n + 2)
CFG (n + 1)
CFG (n + 3)
SDO
SCK
1
SCK
1n
n + 1
15
1
n
n + 1
15
1
n
n + 1
15
SCK
1
XXX
NOTE 1
NOTE 2
CFG (n)
CFG (n + 1)
CFG (n + 2)
CFG (n)
CFG (n + 1)
CFG (n + 2)
CFG (n + 3)
CONVERSION
(n – 1) UNDEFINED
07
35
1-
03
7
DATA (n – 1)
XXX
DATA (n – 2)
XXX
DATA (n – 3)
XXX
DATA (n – 2)
XXX
DATA (n – 1)
XXX
Figure 37. General Interface Timing for the AD7949 With a Busy Indicator
相关PDF资料 |
PDF描述 |
|---|---|
| AD7951BSTZRL | IC ADC 14BIT 1MSPS 48-LQFP |
| AD7952BCPZ | IC ADC 14BIT DIFF 1MSPS 48LFCSP |
| AD7980ARMZ | ADC 16BIT 1MSPS LP 10-MSOP |
| AD7982BCPZ-RL | IC ADC 18BIT 1MSPS PULSAR 10LFCS |
| AD7983BCPZ-RL7 | IC ADC 16BIT 1.33MSPS 10LFCSP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7949SCPZ-EP-R2 | 功能描述:14 Bit Analog to Digital Converter 8 Input 1 SAR 20-LFCSP-WQ (4x4) 制造商:analog devices inc. 系列:PulSAR? 包装:剪切带（CT） 零件状态:有效 位数:14 采样率（每秒）:256k 输入数:8 输入类型:差分，单端 数据接口:SPI，DSP 配置:MUX-ADC 无线电 - S/H:ADC:- A/D 转换器数:1 架构:SAR 参考类型:外部， 内部 电压 - 电源，模拟:2.3 V ~ 5.5 V 电压 - 电源，数字:2.3 V ~ 5.5 V 特性:温度传感器 工作温度:-55°C ~ 125°C 封装/外壳:20-WFQFN 裸露焊盘，CSP 供应商器件封装:20-LFCSP-WQ（4x4） 标准包装:1 |
| AD7949SCPZ-EP-RL7 | 制造商:Analog Devices 功能描述:ADC Single SAR 250ksps 14-bit Serial 20-Pin LFCSP EP T/R 制造商:Analog Devices 功能描述:8 CH 250KSPS 14BIT ADC IC - Tape and Reel 制造商:Analog Devices 功能描述:IC ADC 14BIT 8CH 250KSPS 20LFCSP 制造商:Analog Devices 功能描述:Analog to Digital Converters - ADC 14-Bit 8CH 250 kSPS 制造商:Analog Devices 功能描述:CONVERTER - ADC |
| AD795 | 制造商:AD 制造商全称:Analog Devices 功能描述:Low Power, Low Noise Precision FET Op Amp |
| AD795_02 | 制造商:AD 制造商全称:Analog Devices 功能描述:Low Power, Low Noise Precision FET Op Amp |
| AD795_09 | 制造商:AD 制造商全称:Analog Devices 功能描述:Low Power, Low Noise Precision FET Op Amp |
发布紧急采购，3分钟左右您将得到回复。