- 您现在的位置：买卖IC网 > PDF目录17099 > AD9148-EBZ (Analog Devices Inc)BOARD EVALUATION FOR AD9148 PDF资料下载
参数资料
| 型号： | AD9148-EBZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 40/72页 |
| 文件大小： | 0K |
| 描述： | BOARD EVALUATION FOR AD9148 |
| 设计资源： | AD9148-EBZ Schematic AD9148-EBZ BOM AD9148-EBZ Gerber Files |
| 标准包装： | 1 |
| 系列： | TxDAC+® |
| DAC 的数量： | 4 |
| 位数： | 16 |
| 采样率（每秒）： | 1G |
| 数据接口： | 串行，SPI? |
| 设置时间： | 20ns |
| DAC 型： | 电流 |
| 工作温度： | -40°C ~ 85°C |
| 已供物品： | 板 |
| 已用 IC / 零件： | AD9148 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页当前第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页
Data Sheet
AD9148
Rev. B | Page 45 of 72
DEVICE SYNCHRONIZATION
SYNCHRONIZING MULTIPLE DEVICES
System demands may require that the outputs of multiple DACs
be synchronized with each other or with a system clock. Systems
that support transmit diversity or beam-forming, where multiple
antennas are used to transmit a correlated signal, require multiple
DAC outputs to be phase aligned with each other. Systems with
a time-division multiplexing transmit chain may require one or
more DACs to be synchronized with a system-level reference clock.
Multiple devices are considered synchronized to each other when
the state of the clock generation state machines is identical for all
parts and time aligned data is being read from the FIFOs of all
parts simultaneously. Devices are considered synchronized to a
system clock when there is a fixed and known relationship between
the clock generation state machine and the data being read from
the FIFO and a particular clock edge of the system clock. The
AD9148 has provisions for enabling multiple devices to be
synchronized to each other or to a system clock.
The AD9148 supports synchronization in two different modes,
data rate mode and FIFO rate mode. The two modes are
distinguished by the lowest rate clock that the synchronization
logic attempts to synchronize. In data rate mode, the input data
rate represents the lowest synchronized clock. In FIFO rate mode,
the FIFO rate, which is the data rate divided by the FIFO depth
of 8, represents the lowest rate clock. The advantage of the FIFO
rate synchronization is increased setup and hold times of DCI
relative to the CLK input. When in data rate synchronization
mode, the elasticity of the FIFO is not used to absorb timing
variations between the data source and DAC, resulting in
tighter setup and hold time requirements.
The method chosen for providing the DAC sampling clock directly
impacts the synchronization methods available. When the device
clock multiplier is used, only data rate synchronization is
available. When the DAC sampling clock is sourced directly,
both data rate mode and FIFO rate mode synchronization are
available.
SYNCHRONIZATION WITH CLOCK MULTIPLICATION
When using the clock multiplier to generate the DACCLK, the
REFCLK/SYNC input signal acts as both the reference clock for
the PLL-based clock multiplier and as the synchronization signal.
To synchronize devices, the REFCLK/SYNC signal must be
distributed with low skew to all of the devices to be synchronized.
Skew between the REFCLK/SYNC signals of different devices show
up directly as a timing mismatch at the DAC outputs.
The frequency of the REFCLK/SYNC signal is typically equal to
the input data rate. The FRAME signal and DCI signals can be
created in the FPGA along with the data. A circuit diagram of a
typical configuration is shown in Figure 53.
SYSTEM CLOCK
FPGA
LOW SKEW
CLOCK DRIVER
MATCHED
LENGTH TRACES
MATCHED
LENGTH TRACES
REFCLK/SYNC
FRAME
DCI
REFCLK/SYNC
FRAME
DCI
OUT1
OUT2
08910-
052
Figure 53. Typical Circuit Diagram for Synchronizing Devices with Clock Multiplication Enabled
相关PDF资料 |
PDF描述 |
|---|---|
| SCRH124-150 | INDUCTOR SMD 15UH 3.20A 100KHZ |
| SCRH6D28-470 | INDUCTOR SMD 47UH 0.80A 10KHZ |
| 0982660828 | CBL 13POS 0.5MM JMPR TYPE D 10" |
| HCM12DSEN-S243 | CONN EDGECARD 24POS .156 EYELET |
| RBM12DCAD | CONN EDGECARD 24POS R/A .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD9148-M5372-EBZ | 功能描述:BOARD EVAL FOR AD9149, ADL5372 RoHS:是 类别:编程器，开发系统 >> 评估板 - 数模转换器 (DAC) 系列:* 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- DAC 的数量:4 位数:12 采样率（每秒）:- 数据接口:串行，SPI? 设置时间:3µs DAC 型:电流/电压 工作温度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
| AD9148-M5375-EBZ | 功能描述:BOARD EVAL FOR AD9149, ADL5375 RoHS:是 类别:编程器，开发系统 >> 评估板 - 数模转换器 (DAC) 系列:* 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- DAC 的数量:4 位数:12 采样率（每秒）:- 数据接口:串行，SPI? 设置时间:3µs DAC 型:电流/电压 工作温度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
| AD9152BCPZ | 功能描述:16 Bit Digital to Analog Converter 2 56-LFCSP-WQ (8x8) 制造商:analog devices inc. 系列:TxDAC+? 包装:托盘 零件状态:有效 位数:16 数模转换器数:2 建立时间:- 输出类型:Current - Unbuffered 差分输出:是 数据接口:JESD204B 参考类型:内部 电压 - 电源，模拟:3.13 V ~ 3.47 V 电压 - 电源，数字:1.14 V ~ 1.26 V INL/DNL（LSB）:±10，±5 架构:电流源 工作温度:-40°C ~ 85°C 封装/外壳:56-WFQFN 裸焊盘，CSP 供应商器件封装:56-LFCSP-WQ（8x8） 标准包装:1 |
| AD9152BCPZRL | 功能描述:16 Bit Digital to Analog Converter 2 56-LFCSP-WQ (8x8) 制造商:analog devices inc. 系列:TxDAC+? 包装:带卷（TR） 零件状态:有效 位数:16 数模转换器数:2 建立时间:- 输出类型:Current - Unbuffered 差分输出:是 数据接口:JESD204B 参考类型:内部 电压 - 电源，模拟:3.13 V ~ 3.47 V 电压 - 电源，数字:1.14 V ~ 1.26 V INL/DNL（LSB）:±10，±5 架构:电流源 工作温度:-40°C ~ 85°C 封装/外壳:56-WFQFN 裸焊盘，CSP 供应商器件封装:56-LFCSP-WQ（8x8） 标准包装:2,500 |
| AD9152-EBZ | 功能描述:AD9152 TxDAC+? Series 16 Bit 2.25G Samples Per Second Digital to Analog Converter (DAC) Evaluation Board 制造商:analog devices inc. 系列:TxDAC+? 零件状态:有效 DAC 数:2 位数:16 采样率（每秒）:2.25G 数据接口:SPI 建立时间:- DAC 类型:电流 工作温度:-40°C ~ 85°C 所含物品:板，线缆 使用的 IC/零件:AD9152 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。