- 您现在的位置：买卖IC网 > PDF目录16849 > AD9512/PCBZ (Analog Devices Inc)BOARD EVAL FOR AD9512 PDF资料下载
参数资料
| 型号： | AD9512/PCBZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 38/48页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FOR AD9512 |
| 设计资源： | AD9512 Eval Brd BOM AD9511/12 All Layers AD9511/12 Schematics AD9511/12 Gerber Files |
| 标准包装： | 1 |
| 主要目的： | 计时，时钟分配 |
| 已用 IC / 零件： | AD9512 |
| 已供物品： | 板 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页当前第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页
AD9512
Rev. A | Page 43 of 48
POWER SUPPLY
The AD9512 requires a 3.3 V ± 5% power supply for VS.
The tables in the Specifications section give the performance
expected from the AD9512 with the power supply voltage
within this range. The absolute maximum range of 0.3 V to
+3.6 V, with respect to GND, must never be exceeded on
the VS pin.
Good engineering practice should be followed in the layout of
power supply traces and ground plane of the PCB. The power
supply should be bypassed on the PCB with adequate
capacitance (>10 μF). The AD9512 should be bypassed with
adequate capacitors (0.1 μF) at all power pins, as close as
possible to the part. The layout of the AD9512 evaluation board
(AD9512/PCB) is a good example.
The AD9512 is a complex part that is programmed for its
desired operating configuration by on-chip registers. These
registers are not maintained over a shutdown of external power.
This means that the registers can lose their programmed values
if VS is lost long enough for the internal voltages to collapse.
Careful bypassing should protect the part from memory loss
under normal conditions. Nonetheless, it is important that the
VS power supply not become intermittent, or the AD9512 risks
losing its programming.
The internal bias currents of the AD9512 are set by the RSET
resistors. This resistor should be as close as possible to the value
given as conditions in the Specifications section
(RSET = 4.12 kΩ). This is a standard 1% resistor value and should
be readily obtainable. The bias currents set by this resistor
determine the logic levels and operating conditions of the
internal blocks of the AD9512. The performance figures given
in the Specifications section assume that this specific resistor
value is used.
The exposed metal paddle on the AD9512 package is an
electrical connection, as well as a thermal enhancement. For
the device to function properly, the paddle must be properly
attached to ground (GND). The PCB acts as a heat sink for the
AD9512; therefore, this GND connection should provide a
good thermal path to a larger dissipation area, such as a ground
plane on the PCB. See the layout of the AD9512 evaluation
board (AD9512/PCB or AD9512-VCO/PCB) for a good
example.
POWER MANAGEMENT
The power usage of the AD9512 can be managed to use only the
power required for the functions that are being used. Unused
features and circuitry can be powered down to save power. The
following circuit blocks can be powered down, or are powered
down when not selected (see the Register Map and Description
section):
Any of the dividers are powered down when bypassed—
equivalent to divide-by-one.
The adjustable delay block on OUT4 is powered down
when not selected.
Any output can be powered down. However, LVPECL
outputs have both a safe and an off condition. When the
LVPECL output is terminated, only the safe shutdown
should be used to protect the LVPECL output devices. This
still consumes some power.
The entire distribution section can be powered down when
not needed.
Powering down a functional block does not cause the
programming information for that block (in the registers) to be
lost. This means that blocks can be powered on and off without
otherwise having to reprogram the AD9512. However,
synchronization is lost. A SYNC must be issued to
resynchronize (see the Single-Chip Synchronization section).
相关PDF资料 |
PDF描述 |
|---|---|
| IFSC1008ABER100M01 | INDUCTOR POWER 10UH 0.75A SMD |
| AD9518-1A/PCBZ | BOARD EVALUATION FOR AD9518-1A |
| V150C5C100B | CONVERTER MOD DC/DC 5V 100W |
| AD9522-4/PCBZ | BOARD EVAL FOR AD9522-4 CLK GEN |
| AD9520-0/PCBZ | BOARD EVAL AD9520-0 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD9512UCPZ-EP | 功能描述:IC CLOCK DIST 5OUT PLL 48LFCSP RoHS:是 类别:集成电路 (IC) >> 时钟/计时 - 时钟发生器，PLL，频率合成器 系列:- 标准包装:2,000 系列:- 类型:PLL 时钟发生器 PLL:带旁路 输入:LVCMOS，LVPECL 输出:LVCMOS 电路数:1 比率 - 输入:输出:2:11 差分 - 输入:输出:是/无 频率 - 最大:240MHz 除法器/乘法器:是/无 电源电压:3.135 V ~ 3.465 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:32-LQFP 供应商设备封装:32-TQFP（7x7） 包装:带卷 (TR) |
| AD9512UCPZ-EP-R7 | 功能描述:IC CLOCK DIST 5OUT PLL 48LFCSP RoHS:是 类别:集成电路 (IC) >> 时钟/计时 - 时钟发生器，PLL，频率合成器 系列:- 标准包装:2,000 系列:- 类型:PLL 时钟发生器 PLL:带旁路 输入:LVCMOS，LVPECL 输出:LVCMOS 电路数:1 比率 - 输入:输出:2:11 差分 - 输入:输出:是/无 频率 - 最大:240MHz 除法器/乘法器:是/无 电源电压:3.135 V ~ 3.465 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:32-LQFP 供应商设备封装:32-TQFP（7x7） 包装:带卷 (TR) |
| AD9513 | 制造商:AD 制造商全称:Analog Devices 功能描述:800 MHz Clock Distribution IC, Dividers, Delay Adjust, Three Outputs |
| AD9513/PCB | 制造商:Analog Devices 功能描述:EVAL BD FOR AD9513 ,800 MHZ CLOCK DISTRIBUTION IC, DIVIDERS, - Bulk |
| AD9513/PCBZ | 功能描述:BOARD EVAL FOR AD9513 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:PSoC® 主要目的:电源管理，热管理 嵌入式:- 已用 IC / 零件:- 主要属性:- 次要属性:- 已供物品:板，CD，电源 |
发布紧急采购，3分钟左右您将得到回复。