- 您现在的位置：买卖IC网 > PDF目录11768 > AD9883ABSTZ-RL110 (Analog Devices Inc)IC INTERFACE FLAT 110MHZ 80LQFP PDF资料下载
参数资料
| 型号： | AD9883ABSTZ-RL110 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 8/28页 |
| 文件大小： | 0K |
| 描述： | IC INTERFACE FLAT 110MHZ 80LQFP |
| 标准包装： | 1 |
| 应用： | 显示器，监控器，电视 |
| 接口： | 模拟 |
| 电源电压： | 3 V ~ 3.6 V |
| 封装/外壳： | 80-LQFP |
| 供应商设备封装： | 80-LQFP（14x14） |
| 包装： | 标准包装 |
| 安装类型： | 表面贴装 |
| 其它名称： | AD9883ABSTZ-RL110DKR |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
REV. B
AD9883A
–16–
Table VI. Control Register Map (continued)
Write and
Hex
Read or
Default
Register
Address
Read Only
Bits
Value
Name
Function
0FH
R/W
7:1
0
*******
Bit 7 – Clamp Function. Chooses between Hsync for Clamp
signal or another external signal to be used for clamping.
(Logic 0 = Hsync, Logic 1 = Clamp.)
*1******
Bit 6 – Clamp Polarity. Valid only with external Clamp signal.
(Logic 0 = Active High, Logic 1 Selects Active Low.)
**0*****
Bit 5 – Coast Select. Logic 0 selects the coast input pins to be
used for the PLL coast. Logic 1 selects Vsync to be used for the
PLL coast.
***0****
Bit 4 – Coast Polarity Override. (Logic 0 = Polarity determined by
chip, Logic 1 = Polarity set by Bit 3 in register 0FH.)
****1***
Bit 3 – Coast Polarity. Selects polarity of external Coast signal.
(Logic 0 = Active Low, Logic 1 = Active High.)
*****1**
Bit 2 – Seek Mode Override. (Logic 1 = Allow Low Power Mode,
Logic 0 = Disallow Low Power Mode.)
******1*
Bit 1 – PWRDN. Full Chip Power-Down, Active Low. (Logic 0 =
Full Chip Power-Down, Logic 1 = Normal.)
10H
R/W
7:3
10111
***
Sync-on-Green
Sync-on-Green Threshold. Sets the voltage level of the Sync-on-
Threshold
Green slicer’s comparator.
*****0**
Bit 2 – Red Clamp Select. Logic 0 selects clamp to ground.
Logic 1 selects clamp to midscale (voltage at Pin 37).
******0*
Bit 1 – Green Clamp Select. Logic 0 selects clamp to ground.
Logic 1 selects clamp to midscale (voltage at Pin 37).
*******0
Bit 0 – Blue Clamp Select. Logic 0 selects clamp to ground.
Logic 1 selects clamp to midscale (voltage at Pin 37).
11H
R/W
7:0
00100000
Sync Separator
Sync Separator Threshold. Sets how many internal 5 MHz clock
Threshold
periods the sync separator will count to before toggling high or low.
This should be set to some number greater than the maximum
Hsync or equalization pulsewidth.
12H
R/W
7:0
00000000
Pre-Coast
Pre-Coast. Sets the number of Hsync periods that Coast becomes
active prior to Vsync.
13H
R/W
7:0
00000000
Post-Coast
Post-Coast. Sets the number of Hsync periods that Coast stays
active following Vsync.
14H
RO
7:0
Sync Detect
Bit 7 – Hsync detect. It is set to Logic 1 if Hsync is present on the
analog interface; otherwise it is set to Logic 0.
Bit 6 – AHS: Active Hsync. This bit indicates which analog Hsync
is being used. (Logic 0 = Hsync Input Pin, Logic 1 = Hsync from
Sync-on-Green.)
Bit 5 – Input Hsync Polarity Detect. (Logic 0 = Active Low,
Logic 1 = Active High.)
Bit 4 – Vsync Detect. It is set to Logic 1 if Vsync is present on the
analog interface; otherwise it is set to Logic 0.
Bit 3 – AVS: Active Vsync. This bit indicates which analog Vsync
is being used. (Logic 0 = Vsync Input Pin, Logic 1 = Vsync from
Sync Separator.)
Bit 2 – Output Vsync Polarity Detect. (Logic 0 = Active Low,
Logic 1 = Active High.)
Bit 1 – Sync-on-Green Detect. It is set to Logic 1 if sync is present
on the Green video input; otherwise it is set to 0.
Bit 0 – Input Coast Polarity Detect. (Logic 0 = Active Low, Logic 1 =
Active High.)
15H
R/
W
7:0
1111
****
Test Register
Bits [7:4] Reserved for future use.
****1***
Bit 3 – Must be set to 1 for proper operation.
*****1**
Bit 2 – Must be set to 1 for proper operation.
******1*
Bit 1 – 4:2:2 Output Formatting Mode (Logic 0 = 4:2:2 mode, Logic 1=
4:4:4 mode)
*******1
Bit 0 – Must be set to 0 for proper operation.
相关PDF资料 |
PDF描述 |
|---|---|
| VI-B42-IW-F1 | CONVERTER MOD DC/DC 15V 100W |
| PIC12C509-04I/P | IC MCU OTP 1KX12 8DIP |
| D38999/24WC4PA | CONN RCPT 4POS JAM NUT W/PINS |
| PIC16LF1507-E/P | IC MCU 8BIT 3.5KB FLASH 20PDIP |
| VI-B41-IX-F4 | CONVERTER MOD DC/DC 12V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD9883ABSTZ-RL140 | 功能描述:IC INTERFACE FLAT 140MHZ 80LQFP RoHS:是 类别:集成电路 (IC) >> 接口 - 专用 系列:- 标准包装:3,000 系列:- 应用:PDA，便携式音频/视频，智能电话 接口:I²C，2 线串口 电源电压:1.65 V ~ 3.6 V 封装/外壳:24-WQFN 裸露焊盘 供应商设备封装:24-QFN 裸露焊盘（4x4） 包装:带卷 (TR) 安装类型:表面贴装 产品目录页面:1015 (CN2011-ZH PDF) 其它名称:296-25223-2 |
| AD9883AKST-1 | 制造商:Analog Devices 功能描述: |
| AD9883AKST-110 | 制造商:Analog Devices 功能描述:ADC Triple 110Msps 8-bit Parallel 80-Pin LQFP 制造商:Rochester Electronics LLC 功能描述:110MHZ ANALOG INTERFACE FOR SGA FPD - Bulk 制造商:Analog Devices 功能描述:IC INTERFACE GRAPHIC |
| AD9883AKST-140 | 制造商:Analog Devices 功能描述:ADC Triple 140Msps 8-bit Parallel 80-Pin LQFP 制造商:Analog Devices 功能描述:IC INTERFACE ANALOG |
| AD9883AKSTZ-110 | 功能描述:IC FLAT PANEL INTERFACE 80-LQFP RoHS:是 类别:集成电路 (IC) >> 接口 - 专用 系列:- 特色产品:NXP - I2C Interface 标准包装:1 系列:- 应用:2 通道 I²C 多路复用器 接口:I²C，SM 总线 电源电压:2.3 V ~ 5.5 V 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:剪切带 (CT) 安装类型:表面贴装 产品目录页面:825 (CN2011-ZH PDF) 其它名称:568-1854-1 |
发布紧急采购，3分钟左右您将得到回复。