- 您现在的位置：买卖IC网 > PDF目录11767 > AD9985BSTZ-110 (Analog Devices Inc)IC INTERFACE 8BIT 110MSPS 80LQFP PDF资料下载
参数资料
| 型号： | AD9985BSTZ-110 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 21/32页 |
| 文件大小： | 0K |
| 描述： | IC INTERFACE 8BIT 110MSPS 80LQFP |
| 标准包装： | 1 |
| 应用： | 视频 |
| 接口： | 串行 |
| 电源电压： | 2.2 V ~ 3.45 V |
| 封装/外壳： | 80-LQFP |
| 供应商设备封装： | 80-LQFP（14x14） |
| 包装： | 管件 |
| 安装类型： | 表面贴装 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页当前第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
AD9985
Rev. 0 | Page 28 of 32
SYNC STRIPPER
ACTIVITY
DETECT
NEGATIVE PEAK
CLAMP
COMP
SYNC
SOG
HSYNC IN
ACTIVITY
DETECT
MUX 2
HSYNC OUT
PIXEL CLOCK
MUX 1
SYNC SEPARATOR
INTEGRATOR
VSYNC
SOG OUT
HSYNC OUT
VSYNC OUT
MUX 4
VSYNC IN
1/S
PLL
HSYNC
ACTIVITY
DETECT
AD9985
CLOCK
GENERATOR
POLARITY
DETECT
POLARITY
DETECT
POLARITY
DETECT
MUX 3
COAST
04799-0-0015
Figure 14. Sync Processing Block Diagram
Table 43. Control of the Sync Block Muxes via the Serial Register
Serial Bus
Control
Mux No.
Control Bit
Bit State
Result
1 and 2
0EH: Bit 3
0
Pass Hsync
1
Pass Sync-on-Green
3
0FH: Bit 5
0
Pass Coast
1
Pass Vsync
4
0EH: Bit 0
0
Pass Vsync
1
Pass Sync Separator Signal
SYNC SLICER
The purpose of the sync slicer is to extract the sync signal from
the Green graphics channel. A sync signal is not present on all
graphics systems, only those with Sync-on-Green. The sync
signal is extracted from the Green channel in a two-step
process. First, the SOG input is clamped to its negative peak
(typically 0.3 V below the black level). Next, the signal goes to a
comparator with a variable trigger level, nominally 0.15 V above
the clamped level. The “sliced” sync is typically a composite sync
signal containing both Hsync and Vsync.
SYNC SEPARATOR
A sync separator extracts the Vsync signal from a composite
sync signal. It does this through a low-pass filter-like or
integrator-like operation. It works on the idea that the Vsync
signal stays active for a much longer time than the Hsync signal,
so it rejects any signal shorter than a threshold value, which is
somewhere between an Hsync pulsewidth and a Vsync
pulsewidth.
The sync separator on the AD9985 is simply an 8-bit digital
counter with a 5 MHz clock. It works independently of the
polarity of the composite sync signal. (Polarities are determined
elsewhere on the chip.) The basic idea is that the counter counts
up when Hsync pulses are present. But since Hsync pulses are
relatively short in width, the counter only reaches a value of N
before the pulse ends. It then starts counting down, eventually
reaching 0 before the next Hsync pulse arrives. The specific
value of N will vary for different video modes, but will always
be less than 255. For example, with a 1 s width Hsync, the
counter will only reach 5 (1 s/200 ns = 5). When Vsync is
present on the composite sync, the counter will also count up.
However, since the Vsync signal is much longer, it will count to
a higher number M. For most video modes, M will be at least
255. So, Vsync can be detected on the composite sync signal by
detecting when the counter counts to higher than N. The
specific count that triggers detection (T) can be programmed
through the serial register (11H).
Once Vsync has been detected, there is a similar process to
detect when it goes inactive. At detection, the counter first resets
to 0, then starts counting up when Vsync goes away. Similar to
the previous case, it will detect the absence of Vsync when the
counter reaches the threshold count (T). In this way, it will
reject noise and/or serration pulses. Once Vsync is detected to
be absent, the counter resets to 0 and begins the cycle again.
相关PDF资料 |
PDF描述 |
|---|---|
| AD9882AKSTZ-100 | IC INTERFACE/DVI 100MHZ 100LQFP |
| AD9882KSTZ-100 | IC INTERFACE/DVI 100MHZ 100LQFP |
| MS27473E16B55PA | CONN PLUG 55POS STRAIGHT W/PINS |
| LTC4305IGN#TR | IC BUFFER BUS 2WR ADDRESS 16SSOP |
| VI-B43-IW-F2 | CONVERTER MOD DC/DC 24V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD9985KST-110 | 制造商:Analog Devices 功能描述:110 MSPS/140 MSPS ANLG INTRFC FOR FLAT PNL DISPLAYS 80LQFP - Bulk |
| AD9985KSTZ-110 | 功能描述:IC INTERFACE 8BIT 110MSPS 80LQFP RoHS:是 类别:集成电路 (IC) >> 接口 - 专用 系列:- 特色产品:NXP - I2C Interface 标准包装:1 系列:- 应用:2 通道 I²C 多路复用器 接口:I²C，SM 总线 电源电压:2.3 V ~ 5.5 V 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:剪切带 (CT) 安装类型:表面贴装 产品目录页面:825 (CN2011-ZH PDF) 其它名称:568-1854-1 |
| AD9985KSTZ-140 | 功能描述:IC INTERFACE 8BIT 140MSPS 80LQFP RoHS:是 类别:集成电路 (IC) >> 接口 - 专用 系列:- 标准包装:3,000 系列:- 应用:PDA，便携式音频/视频，智能电话 接口:I²C，2 线串口 电源电压:1.65 V ~ 3.6 V 封装/外壳:24-WQFN 裸露焊盘 供应商设备封装:24-QFN 裸露焊盘（4x4） 包装:带卷 (TR) 安装类型:表面贴装 产品目录页面:1015 (CN2011-ZH PDF) 其它名称:296-25223-2 |
| AD9990 | 制造商:AD 制造商全称:Analog Devices 功能描述:Dual Channel, 14-Bit CCD Signal Processor with V-Driver and Precision Timing |
| AD9990BBCZ | 功能描述:IC CCD SGNL PROCESSOR 112CSPBGA RoHS:是 类别:集成电路 (IC) >> 接口 - 传感器和探测器接口 系列:- 其它有关文件:Automotive Product Guide 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:74 系列:- 类型:触控式传感器 输入类型:数字 输出类型:数字 接口:JTAG，串行 电流 - 电源:100µA 安装类型:表面贴装 封装/外壳:20-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:20-TSSOP 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。