- 您现在的位置：买卖IC网 > PDF目录20504 > ADM1041A-EVALZ (Analog Devices Inc)BOARD EVAL FOR ADM1041A PDF资料下载
参数资料
| 型号： | ADM1041A-EVALZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 14/56页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FOR ADM1041A |
| 标准包装： | 1 |
| 主要目的： | AC/DC，次级 |
| 输出及类型： | 1，非隔离 |
| 功率 - 输出： | 24W |
| 输出电压： | 12V |
| 电流 - 输出： | 2A |
| 输入电压： | 85 ~ 132VAC |
| 板类型： | 完全填充 |
| 已供物品： | 板，线缆，软件 |
| 已用 IC / 零件： | ADM1041A |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页
ADM1041A
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
ADM1041A
V DD 1
V LS /C S –/FS 2
C S + 3
C CMP 4
V CMP 5
F D 6
GND 7
ICT 8
PULSE/AC SENSE 1/MON1 9
AC SENSE 2/MON2 10
CBD/ALERT 11
PEN 12
24 SHRO
23 SHRS+
22 SCMP
21 V S +
20 V S –/SHRS–
19 F G
TOP VIEW
(Not to Scale) 18 AC_OK/OTP/MON5
17 DC_OK/MON4
16 PSON/MON3
15 ADD0
14 SDA/PS ON LINK
13 SCL/AC_OKLink
Figure 7. Pin Configuration
Table 3. Pin Function Descriptions
Pin No.
1
2
3
4
5
6
7
8
9
Mnemonic
V DD
V LS /C S –/FS
C S +
C CMP
V CMP
F D
GND
ICT
PULSE/AC SENSE 1/
MON1
Description
Positive Supply for the ADM1041A. Normal range is 4.5 V to 5.5 V. Absolute maximum rating is 6.5 V.
Inverting Differential Current Sense Input, Local Voltage Sense Pin, and OrFET Source. These three functions
are served by a common divider. The local voltage sense input is used for local overvoltage and undervoltage
sensing. This pin also provides an input to the false UV clamp that prevents shutdown during an external load
overvoltage condition. When supporting an OrFET circuit, this pin represents the FET source and is the
inverting input of a differential amplifier looking for the presence of a reverse voltage across the FET, which
might indicate a failure mode.
Noninverting Differential Current Sense Input. The differential sensitivity of C S + and C S – is normally around 10
mV to 40 mV at the input to the ADM1041A. Nulling any external divider offset is achieved by injecting a
trimmable amount of current into either the inverting or noninverting input of the second stage of the
current sense amplifier. A compensation circuit is used to ensure the amount of current for zero-offset tracks
the common-mode voltage. Nulling of any amplifier offset is done in a similar manner except that it does not
track the common-mode voltage.
Current Error Amplifier Compensation. This pin is the output of the current limit transconductance error
amplifier. A series resistor and a capacitor to ground are required for loop compensation.
Voltage Error Amplifier Compensation. This is the output of a voltage error transconductance amplifier.
Compensate with a series capacitor and resistor to ground. An external emitter-follower or buffer is typically
used to drive an optocoupler. Output voltage positioning may be obtained by placing a second resistor
directly to ground. Refer to Analog Devices applications notes on voltage positioning.
A divider from the OrFET drain is connected here. A differential amplifier is then used to detect the presence
of a reverse voltage across the FET, which indicates a fault condition and causes the OrFET gate to be pulled
low.
Ground. This pin is double bonded for extra reliability. If the ground pin goes positive with respect to the
remote sense return (V S –) for a sustained period indicating that the negative remote sense line is
disconnected, PEN is disabled.
Input for Current Transformer. The sensitivity of this pin is suitable for the typical 0.5 V to 1 V signal that is
normally available. If this function is enabled, the C S + amplifier is disabled. This pin is also used for extended
SMBus addressing, that is, pulled below ground to allow additional SMBus addresses.
Pulse Present, AC/Bulk Sense 1, or Monitor 1 Input.
PULSE: This tells the OrFET circuit that the voltage from the power transformer is normal. A peak hold allows
the OrFET circuit to pass through the pulse skipping that occurs with very light loads, but turns off the circuit
about one second after the last pulse is recognized.
AC SENSE 1: This sense function also uses the peak voltage on this pin to measure the bulk capacitor voltage. If
too low, AC_OK and DC_OK can warn of an imminent loss of power. Threshold level and hysteresis can be
trimmed. When not selected, AC SENSE 1 defaults to true.
MON1: When MON1 is selected for this pin, its input is compared against a 1.25 V comparator that could be
used for monitoring a postregulated output; includes overvoltage, undervoltage, and overtemperature
conditions.
Rev. 0 | Page 14 of 56
相关PDF资料 |
PDF描述 |
|---|---|
| VI-23V-CX-S | CONVERTER MOD DC/DC 5.8V 75W |
| T95D277M004LZSL | CAP TANT 270UF 4V 20% 2917 |
| SBRB1545CTG | DIODE SCHOTTKY 7.5A 45V D2PAK |
| RCM06DTMN | CONN EDGECARD 12POS R/A .156 SLD |
| MBR2090CTG | DIODE SCHOTTKY 90V 20A TO220AB |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADM1041ARQ | 功能描述:IC PWR SUPP MON/LOAD SHAR 24QSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
| ADM1041ARQ-2 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: |
| ADM1041ARQ-REEL | 制造商:AD 制造商全称:Analog Devices 功能描述:Secondary-Side Controller with Current Share and Housekeeping |
| ADM1041ARQ-REEL7 | 功能描述:IC PWR SUP MON/LOAD SHARE 24QSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
| ADM1041ARQZ | 功能描述:IC PWR SUPP MON/LOAD SHAR 24QSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。