- 您现在的位置：买卖IC网 > PDF目录20504 > ADM1041A-EVALZ (Analog Devices Inc)BOARD EVAL FOR ADM1041A PDF资料下载
参数资料
| 型号： | ADM1041A-EVALZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 16/56页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FOR ADM1041A |
| 标准包装： | 1 |
| 主要目的： | AC/DC，次级 |
| 输出及类型： | 1，非隔离 |
| 功率 - 输出： | 24W |
| 输出电压： | 12V |
| 电流 - 输出： | 2A |
| 输入电压： | 85 ~ 132VAC |
| 板类型： | 完全填充 |
| 已供物品： | 板，线缆，软件 |
| 已用 IC / 零件： | ADM1041A |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页
ADM1041A
Pin No.
23
24
Mnemonic
SHRS+
SHRO
Description
Current Share Sense. This is the noninverting input of a differential sense amplifier looking at the voltage on
the share bus. For testing purposes, this pin is normally connected to SHRO. Calibration always expects this
pin to be at 2.0 V with respect to SHRS–/V S –. If a higher share voltage is required, a resistor divider from SHRO
or an additional gain stage, must be used.
Current Share Output. This output is capable of driving the share bus of several power supplies between 0 V
and V DD – 0.4 V (10 kΩ bus pull-down in each supply). Where a higher share bus voltage is required, an
external amplifier is necessary. The current share output from the supply, when bused with the share output
of other power supplies working in parallel, allows each of the supplies to contribute essentially equal
currents to the load.
Table 4. Default Pin States During EEPROM Download
Pin No.
11
12
17
18
19
Mnemonic
CBD
PEN
DC_OK
AC_OK
F G
State
High impedance (Hi-Z) at power-up and until the end of the EEPROM download (approximately 20 ms).
This pin is reconfigured at the end of the EEPROM download.
High impedance (Hi-Z) at power-up and until the end of the EEPROM download (approximately 20 ms).
This pin is reconfigured at the end of the EEPROM download.
Active low (low if DC_OK true) at power-up. This pin is reconfigured during the EEPROM download.
Active low (low if DC_OK true) at power-up. This pin is reconfigured during the EEPROM download.
High impedance (Hi-Z) at power-up and until the end of the EEPROM download (approximately 20 ms).
This pin is reconfigured at the end of the EEPROM download.
TERMINOLOGY
Table 5.
Mnemonic
POR
UVL
CVMode
CCMode
UVP
OVP
OCP
OTP
UVB
Description
Power-On Reset. When VDD is initially applied to the ADM1041A, the POR function clears all latches and puts
the logic into a state that allows a clean start-up.
Undervoltage Lockout. This is used on VDD to prevent spurious modes of operation that might occur if VDD
is below a specific voltage.
Constant Voltage Mode. This is the normal mode of operation of the power supply main output. The output
voltage remains constant over the whole range of current specified.
Constant Current Mode. This mode of operation occurs when the output is overloaded until or unless a
shutdown event is triggered. The output current control level remains constant down to 0 V.
Undervoltage Protection. If the output being monitored is detected as going under voltage, the UVP function
sends a fault signal. After a delay, PEN goes false, the output is disabled, and either latch-off or an autorestart
occurs, depending on the mode selected. The DC_OK output also goes false immediately to show that the
output is out of tolerance.
Overvoltage Protection. If the output being monitored is detected as going over voltage, the OVP function
latches and sends a fault signal, PEN goes false, and CBD goes true. The DC_OK output also goes false
immediately. OVP faults are always latching and require the cycling of PSON or VDD or SMBus command to
reset the latch.
Overcurrent Protection. If the output being monitored is detected as going over current for a certain time,
the OCP function sends out a fault signal that triggers a shutdown that can be latched or allowed to
autorestart, depending on the mode selected. Prior to shutting down, the DC_OK output goes false warning
the system that output is going to be lost. The latch is the same one used for OVP. For autorestart, the OCP
timeout period is configurable.
Overtemperature Protection. If the temperature being sensed is detected as going over the selected limit, the
OTP function sends out a fault signal that triggers a shutdown that can be latched or allowed to auto-restart
depending on the mode selected. Prior to shutting down, the DC_OK output goes false warning the system
that output is going to be lost. The latch is the same one used for OVP.
Undervoltage Blanking. The UVP function is blanked (disabled) during power-up or if the ACSENSE function is
false (ac line voltage is low). When in constant current mode, UVB is disabled. The status of ACSENSE must be
known to the IC, either by virtue of the on-board ACSENSE or communicated by the SMBus with the help of
an external microprocessor or by using AC_OKLink. When in constant-current mode, due to an overload, UVB
is applied for the overcurrent ride-through period.
Rev. 0 | Page 16 of 56
相关PDF资料 |
PDF描述 |
|---|---|
| VI-23V-CX-S | CONVERTER MOD DC/DC 5.8V 75W |
| T95D277M004LZSL | CAP TANT 270UF 4V 20% 2917 |
| SBRB1545CTG | DIODE SCHOTTKY 7.5A 45V D2PAK |
| RCM06DTMN | CONN EDGECARD 12POS R/A .156 SLD |
| MBR2090CTG | DIODE SCHOTTKY 90V 20A TO220AB |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADM1041ARQ | 功能描述:IC PWR SUPP MON/LOAD SHAR 24QSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
| ADM1041ARQ-2 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: |
| ADM1041ARQ-REEL | 制造商:AD 制造商全称:Analog Devices 功能描述:Secondary-Side Controller with Current Share and Housekeeping |
| ADM1041ARQ-REEL7 | 功能描述:IC PWR SUP MON/LOAD SHARE 24QSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
| ADM1041ARQZ | 功能描述:IC PWR SUPP MON/LOAD SHAR 24QSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。