- 您现在的位置：买卖IC网 > PDF目录20504 > ADM1041A-EVALZ (Analog Devices Inc)BOARD EVAL FOR ADM1041A PDF资料下载
参数资料
| 型号： | ADM1041A-EVALZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 36/56页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FOR ADM1041A |
| 标准包装： | 1 |
| 主要目的： | AC/DC，次级 |
| 输出及类型： | 1，非隔离 |
| 功率 - 输出： | 24W |
| 输出电压： | 12V |
| 电流 - 输出： | 2A |
| 输入电压： | 85 ~ 132VAC |
| 板类型： | 完全填充 |
| 已供物品： | 板，线缆，软件 |
| 已用 IC / 零件： | ADM1041A |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页当前第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页
ADM1041A
Notes on SMBus Read Operations
The SMBus interface of the ADM1041A cannot load the
SMBUS if no power is applied to the ADM1041A. This
requirement allows a power supply to be disconnected from the
ac supply while still installed in a power subsystem.
When using the SMBus interface, a write always consists of the
ADM1041A SMBus interface address byte, followed by the
internal address register byte, and then the data byte. There are
two cases for a read.
In the first case, if the internal address register is known to be at
the desired address, read the ADM1041A with the SMBus
interface address byte, followed by the data byte read from the
ADM1041A. The internal address pointer increments if a block
mode operation is in progress; data values of 0 are returned if
the register address limit of 7Fh is exceeded or if unused
registers in the address range 00h to 7Fh are accessed. If the
address register is pointing at EEPROM memory, that is 8000h,
and the address reaches its limit of 80FFh, it does not roll over
to Address 8100h on the next access.
Additional accesses do not increment the address pointer, all
reads return 00h, and all writes complete normally but do not
change any internal register or EEPROM location. If the address
register is pointing at EEPROM memory, that is 81xxh, and the
address reaches its limit of 813Fh, it does not roll over to
Address 8140h on the next access.
Additional accesses do not increment the address pointer, all
reads return 00h, and all writes complete normally but do not
change any internal register or EEPROM location. Note that for
byte reads, the internal address does not auto-increment.
In the second case, if the internal address register value is
unknown, write to the ADM1041A with the SMBus interface
address byte, followed by the internal address register byte.
Then restart the serial communication with a read consisting of
the SMBus interface address byte, followed by the data byte read
from the ADM1041A.
SMBus ALERT RESPONSE ADDRESS (ARA)
The ADM1041A CBD/ALERT pin can be configured to
respond to a variety of fault signals and can be used as an
interrupt to a microprocessor. The pins from several
ADM1041As may be wire-OR’ed. When the SMBus master
(microprocessor) detects an alert request, it normally needs to
read the alert status of each device to identify the source of the
alert.
If more than one device asserts an alert, all alerting devices try
to respond with their slave addresses, but an arbitration process
ensures that only the lowest slave address is received by the
master. If the slave device has its alert configured as latching, it
sends a command via the SMBus to clear the latch. The master
should then check if the alert line is still asserted, and, if so,
repeat the ARA call to service the next alert. Note that an
alerting slave does not respond to an ARA call unless it is
configured in SMBus mode (not AC_OKLink/PS ON LINK) and
up_pson_m is set. The ADM1041A supports the SMBus (ARA)
function.
SUPPORT FOR SMBus 1.1
SMBus 1.1 optionally adds a CRC8 frame check sequence to
check if transmissions are received correctly. This is particularly
useful for long block read/write EEPROM operations, when the
SMBus is heavily loaded or in a noisy environment. The CRC8
frame can be used to guarantee reliability of the EEPROM.
LAYOUT CONSIDERATIONS
Noise coupling into the digital lines (greater than 150 mV),
overshoot greater than V CC, and undershoot less than GND
may prevent successful SMBus communication with the
ADM1041A. SMBus No Acknowledge is the most common
symptom, causing unnecessary traffic on the bus. Although the
SMBus maximum frequency of communication is rather low
(400 kHz max), care still needs to be taken to ensure proper
termination within a system with multiple parts on the bus and
long printed circuit board traces. A 5.1 kΩ resistor can be added
in series with the SDA and SCL lines to help filter noise and
ringing. Minimize noise coupling by keeping digital traces out
of switching power supply areas and ensure that digital lines
containing high speed data communications cross at right
angles to the SDA and SCL lines.
POWER-UP AUTO-CONFIGURATION
After power-up or reset, the ADM1041A automatically reads
the content of a 32-byte block of EEPROM memory that starts
at 8100h and transfers the contents into the appropriate trim-
level and control registers (00h to 1Bh). In this way, the
ADM1041A can be preconfigured with the desired operating
characteristics without the host system having to download the
data over the SMBus. This does not preclude the possibility of
modifying the configuration during normal operation.
power-up or power-on reset.
The SMBus ARA provides an easier method to locate the source
of a such an alert. When the master receives an alert, it can send
a general call address (0001100) over the bus. The device assert-
ing the alert responds by returning its own slave address to the
master.
EEPROM
POWER UP
RAM
CONFIGURATION
REGISTERS
DIGITAL
TRIM
POTS
DIGITAL
TIMING
CONTROL
Figure 37. EEPROM Download
Rev. 0 | Page 36 of 56
相关PDF资料 |
PDF描述 |
|---|---|
| VI-23V-CX-S | CONVERTER MOD DC/DC 5.8V 75W |
| T95D277M004LZSL | CAP TANT 270UF 4V 20% 2917 |
| SBRB1545CTG | DIODE SCHOTTKY 7.5A 45V D2PAK |
| RCM06DTMN | CONN EDGECARD 12POS R/A .156 SLD |
| MBR2090CTG | DIODE SCHOTTKY 90V 20A TO220AB |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADM1041ARQ | 功能描述:IC PWR SUPP MON/LOAD SHAR 24QSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
| ADM1041ARQ-2 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: |
| ADM1041ARQ-REEL | 制造商:AD 制造商全称:Analog Devices 功能描述:Secondary-Side Controller with Current Share and Housekeeping |
| ADM1041ARQ-REEL7 | 功能描述:IC PWR SUP MON/LOAD SHARE 24QSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
| ADM1041ARQZ | 功能描述:IC PWR SUPP MON/LOAD SHAR 24QSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。